Guide to the Secure Configuration of Red Hat Enterprise Linux 7

with profile VPP - Protection Profile for Virtualization v. 1.0 for Red Hat Virtualization
This compliance profile reflects the core set of security related configuration settings for deployment of Red Hat Enterprise Linux Hypervisor (RHELH) 7.x into U.S. Defense, Intelligence, and Civilian agencies. Development partners and sponsors include the U.S. National Institute of Standards and Technology (NIST), U.S. Department of Defense, the National Security Agency, and Red Hat. This baseline implements configuration requirements from the following sources: - Committee on National Security Systems Instruction No. 1253 (CNSSI 1253) - NIST 800-53 control selections for MODERATE impact systems (NIST 800-53) - U.S. Government Configuration Baseline (USGCB) - NIAP Protection Profile for Virtualization v1.0 (VPP v1.0) For any differing configuration requirements, e.g. password lengths, the stricter security setting was chosen. Security Requirement Traceability Guides (RTMs) and sample System Security Configuration Guides are provided via the scap-security-guide-docs package. This profile reflects U.S. Government consensus content and is developed through the ComplianceAsCode project, championed by the National Security Agency. Except for differences in formatting to accommodate publishing processes, this profile mirrors ComplianceAsCode content as minor divergences, such as bugfixes, work through the consensus and release processes.
This guide presents a catalog of security-relevant configuration settings for Red Hat Enterprise Linux 7. It is a rendering of content structured in the eXtensible Configuration Checklist Description Format (XCCDF) in order to support security automation. The SCAP content is is available in the scap-security-guide package which is developed at https://www.open-scap.org/security-policies/scap-security-guide.

Providing system administrators with such guidance informs them how to securely configure systems under their control in a variety of network roles. Policy makers and baseline creators can use this catalog of settings, with its associated references to higher-level security control catalogs, in order to assist them in security baseline creation. This guide is a catalog, not a checklist, and satisfaction of every item is not likely to be possible or sensible in many operational scenarios. However, the XCCDF format enables granular selection and adjustment of settings, and their association with OVAL and OCIL content provides an automated checking capability. Transformations of this document, and its associated automated checking content, are capable of providing baselines that meet a diverse set of policy objectives. Some example XCCDF Profiles, which are selections of items that form checklists and can be used as baselines, are available with this guide. They can be processed, in an automated fashion, with tools that support the Security Content Automation Protocol (SCAP). The DISA STIG, which provides required settings for US Department of Defense systems, is one example of a baseline created from this guidance.

This benchmark is a direct port of a SCAP Security Guide benchmark developed for Red Hat Enterprise Linux. It has been modified through an automated process to remove specific dependencies on Red Hat Enterprise Linux and to function with CentOS. The result is a generally useful SCAP Security Guide benchmark with the following caveats:

  • CentOS is not an exact copy of Red Hat Enterprise Linux. There may be configuration differences that produce false positives and/or false negatives. If this occurs please file a bug report.
  • CentOS has its own build system, compiler options, patchsets, and is a community supported, non-commercial operating system. CentOS does not inherit certifications or evaluations from Red Hat Enterprise Linux. As such, some configuration rules (such as those requiring FIPS 140-2 encryption) will continue to fail on CentOS.

Members of the CentOS community are invited to participate in OpenSCAP and SCAP Security Guide development. Bug reports and patches can be sent to GitHub: https://github.com/ComplianceAsCode/content. The mailing list is at https://fedorahosted.org/mailman/listinfo/scap-security-guide.

Do not attempt to implement any of the settings in this guide without first testing them in a non-operational environment. The creators of this guidance assume no responsibility whatsoever for its use by other parties, and makes no guarantees, expressed or implied, about its quality, reliability, or any other characteristic.

Profile Information

Profile TitleVPP - Protection Profile for Virtualization v. 1.0 for Red Hat Virtualization
Profile IDxccdf_org.ssgproject.content_profile_rhelh-vpp

CPE Platforms

  • cpe:/o:redhat:enterprise_linux:7::client
  • cpe:/o:redhat:enterprise_linux:7::computenode
  • cpe:/o:redhat:enterprise_linux:7::server
  • cpe:/o:redhat:enterprise_linux:7::workstation
  • cpe:/o:redhat:enterprise_linux:7
  • cpe:/o:centos:centos:7

Revision History

Current version: 0.1.68

  • draft (as of 2023-06-15)

Table of Contents

  1. System Settings
    1. Installing and Maintaining Software
    2. Account and Access Control
    3. System Accounting with auditd
    4. GRUB2 bootloader configuration
    5. Network Configuration and Firewalls
    6. File Permissions and Masks
    7. SELinux
  2. Services
    1. SSH Server
    2. System Security Services Daemon

Checklist

Group   Guide to the Secure Configuration of Red Hat Enterprise Linux 7   Group contains 48 groups and 142 rules
Group   System Settings   Group contains 43 groups and 121 rules
[ref]   Contains rules that check correct system settings.
Group   Installing and Maintaining Software   Group contains 6 groups and 11 rules
[ref]   The following sections contain information on security-relevant choices during the initial operating system installation process and the setup of software updates.
Group   System and Software Integrity   Group contains 4 groups and 6 rules
[ref]   System and software integrity can be gained by installing antivirus, increasing system encryption strength with FIPS, verifying installed software, enabling SELinux, installing an Intrusion Prevention System, etc. However, installing or enabling integrity checking tools cannot prevent intrusions, but they can detect that an intrusion may have occurred. Requirements for integrity checking may be highly dependent on the environment in which the system will be used. Snapshot-based approaches such as AIDE may induce considerable overhead in the presence of frequent software updates.
Group   Software Integrity Checking   Group contains 1 group and 3 rules
[ref]   Both the AIDE (Advanced Intrusion Detection Environment) software and the RPM package management system provide mechanisms for verifying the integrity of installed software. AIDE uses snapshots of file metadata (such as hashes) and compares these to current system files in order to detect changes.

The RPM package management system can conduct integrity checks by comparing information in its metadata database with files installed on the system.
Group   Verify Integrity with RPM   Group contains 3 rules
[ref]   The RPM package management system includes the ability to verify the integrity of installed packages by comparing the installed files with information about the files taken from the package metadata stored in the RPM database. Although an attacker could corrupt the RPM database (analogous to attacking the AIDE database as described above), this check can still reveal modification of important files. To list which files on the system differ from what is expected by the RPM database:
$ rpm -qVa
See the man page for rpm to see a complete explanation of each column.

Rule   Verify File Hashes with RPM   [ref]

Without cryptographic integrity protections, system executables and files can be altered by unauthorized users without detection. The RPM package management system can check the hashes of installed software packages, including many that are important to system security. To verify that the cryptographic hash of system files and commands matches vendor values, run the following command to list which files on the system have hashes that differ from what is expected by the RPM database:
$ rpm -Va --noconfig | grep '^..5'
A "c" in the second column indicates that a file is a configuration file, which may appropriately be expected to change. If the file was not expected to change, investigate the cause of the change using audit logs or other means. The package can then be reinstalled to restore the file. Run the following command to determine which package owns the file:
$ rpm -qf FILENAME
The package can be reinstalled from a yum repository using the command:
$ sudo yum reinstall PACKAGENAME
Alternatively, the package can be reinstalled from trusted media using the command:
$ sudo rpm -Uvh PACKAGENAME
Rationale:
The hashes of important files like system executables should match the information given by the RPM database. Executables with erroneous hashes could be a sign of nefarious activity on the system.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_rpm_verify_hashes
Identifiers and References

References:  11, 2, 3, 9, 5.10.4.1, APO01.06, BAI03.05, BAI06.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS06.02, 3.3.8, 3.4.1, CCI-000366, CCI-001749, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.4, SR 3.1, SR 3.3, SR 3.4, SR 3.8, SR 7.6, A.11.2.4, A.12.1.2, A.12.2.1, A.12.5.1, A.12.6.2, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, CM-6(d), CM-6(c), SI-7, SI-7(1), SI-7(6), AU-9(3), PR.DS-6, PR.DS-8, PR.IP-1, Req-11.5, 11.5.2, SRG-OS-000480-GPOS-00227, 6.1.1, SV-214799r854001_rule


Complexity:high
Disruption:medium
Strategy:restrict
- name: 'Set fact: Package manager reinstall command (dnf)'
  set_fact:
    package_manager_reinstall_cmd: dnf reinstall -y
  when: ansible_distribution == "Fedora"
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes

- name: 'Set fact: Package manager reinstall command (yum)'
  set_fact:
    package_manager_reinstall_cmd: yum reinstall -y
  when: (ansible_distribution == "RedHat" or ansible_distribution == "CentOS" or ansible_distribution
    == "OracleLinux")
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes

- name: 'Set fact: Package manager reinstall command (zypper)'
  set_fact:
    package_manager_reinstall_cmd: zypper in -f -y
  when: ansible_distribution == "SLES"
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes

- name: Read files with incorrect hash
  command: rpm -Va --nodeps --nosize --nomtime --nordev --nocaps --nolinkto --nouser
    --nogroup --nomode --noghost --noconfig
  register: files_with_incorrect_hash
  changed_when: false
  failed_when: files_with_incorrect_hash.rc > 1
  check_mode: false
  when: (package_manager_reinstall_cmd is defined)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes

- name: Create list of packages
  command: rpm -qf "{{ item }}"
  with_items: '{{ files_with_incorrect_hash.stdout_lines | map(''regex_findall'',
    ''^[.]+[5]+.* (\/.*)'', ''\1'') | map(''join'') | select(''match'', ''(\/.*)'')
    | list | unique }}'
  register: list_of_packages
  changed_when: false
  check_mode: false
  when:
  - files_with_incorrect_hash.stdout_lines is defined
  - (files_with_incorrect_hash.stdout_lines | length > 0)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes

- name: Reinstall packages of files with incorrect hash
  command: '{{ package_manager_reinstall_cmd }} ''{{ item }}'''
  with_items: '{{ list_of_packages.results | map(attribute=''stdout_lines'') | list
    | unique }}'
  when:
  - files_with_incorrect_hash.stdout_lines is defined
  - (package_manager_reinstall_cmd is defined and (files_with_incorrect_hash.stdout_lines
    | length > 0))
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010020
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_hashes


# Find which files have incorrect hash (not in /etc, because of the system related config files) and then get files names
files_with_incorrect_hash="$(rpm -Va --noconfig | grep -E '^..5' | awk '{print $NF}' )"

# From files names get package names and change newline to space, because rpm writes each package to new line
packages_to_reinstall="$(rpm -qf $files_with_incorrect_hash | tr '\n' ' ')"


yum reinstall -y $packages_to_reinstall

Rule   Verify and Correct Ownership with RPM   [ref]

The RPM package management system can check file ownership permissions of installed software packages, including many that are important to system security. After locating a file with incorrect permissions, which can be found with
rpm -Va | awk '{ if (substr($0,6,1)=="U" || substr($0,7,1)=="G") print $NF }'
run the following command to determine which package owns it:
$ rpm -qf FILENAME
Next, run the following command to reset its permissions to the correct values:
$ sudo rpm --setugids PACKAGENAME
Warning:  Profiles may require that specific files be owned by root while the default owner defined by the vendor is different. Such files will be reported as a finding and need to be evaluated according to your policy and deployment environment.
Rationale:
Ownership of binaries and configuration files that is incorrect could allow an unauthorized user to gain privileges that they should not have. The ownership set by the vendor should be maintained. Any deviations from this baseline should be investigated.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_rpm_verify_ownership
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 3, 5, 6, 9, 5.10.4.1, APO01.06, APO11.04, BAI03.05, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.04, DSS05.07, DSS06.02, MEA02.01, 3.3.8, 3.4.1, CCI-001494, CCI-001496, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.7.3, 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 5.2, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.5.1, A.12.6.2, A.12.7.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R4.2, CIP-003-8 R6, CIP-007-3 R4, CIP-007-3 R4.1, CIP-007-3 R4.2, CM-6(d), CM-6(c), SI-7, SI-7(1), SI-7(6), AU-9(3), PR.AC-4, PR.DS-5, PR.IP-1, PR.PT-1, Req-11.5, 11.5.2, SRG-OS-000256-GPOS-00097, SRG-OS-000257-GPOS-00098, SRG-OS-000278-GPOS-00108, 1.7.1.4, 1.7.1.5, 1.7.1.6, 6.1.1, 6.1.2, 6.1.3, 6.1.4, 6.1.5, 6.1.6, 6.1.7, 6.1.8, 6.1.9, SV-204392r880752_rule


Complexity:high
Disruption:medium
Strategy:restrict
- name: Read list of files with incorrect ownership
  command: rpm -Va --nodeps --nosignature --nofiledigest --nosize --nomtime --nordev
    --nocaps --nolinkto --nomode
  register: files_with_incorrect_ownership
  failed_when: files_with_incorrect_ownership.rc > 1
  changed_when: false
  check_mode: false
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_ownership

- name: Create list of packages
  command: rpm -qf "{{ item }}"
  with_items: '{{ files_with_incorrect_ownership.stdout_lines | map(''regex_findall'',
    ''^[.]+[U|G]+.* (\/.*)'', ''\1'') | map(''join'') | select(''match'', ''(\/.*)'')
    | list | unique }}'
  register: list_of_packages
  changed_when: false
  check_mode: false
  when: (files_with_incorrect_ownership.stdout_lines | length > 0)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_ownership

- name: Correct file ownership with RPM
  command: rpm --setugids '{{ item }}'
  with_items: '{{ list_of_packages.results | map(attribute=''stdout_lines'') | list
    | unique }}'
  when: (files_with_incorrect_ownership.stdout_lines | length > 0)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_ownership

Complexity:high
Disruption:medium
Strategy:restrict

# Declare array to hold set of RPM packages we need to correct permissions for
declare -A SETPERMS_RPM_DICT

# Create a list of files on the system having permissions different from what
# is expected by the RPM database
readarray -t FILES_WITH_INCORRECT_PERMS < <(rpm -Va --nofiledigest | awk '{ if (substr($0,6,1)=="U" || substr($0,7,1)=="G") print $NF }')

for FILE_PATH in "${FILES_WITH_INCORRECT_PERMS[@]}"
do
        RPM_PACKAGE=$(rpm -qf "$FILE_PATH")
	# Use an associative array to store packages as it's keys, not having to care about duplicates.
	SETPERMS_RPM_DICT["$RPM_PACKAGE"]=1
done

# For each of the RPM packages left in the list -- reset its permissions to the
# correct values
for RPM_PACKAGE in "${!SETPERMS_RPM_DICT[@]}"
do
        rpm --setugids "${RPM_PACKAGE}"
done

Rule   Verify and Correct File Permissions with RPM   [ref]

The RPM package management system can check file access permissions of installed software packages, including many that are important to system security. Verify that the file permissions of system files and commands match vendor values. Check the file permissions with the following command:
$ sudo rpm -Va | awk '{ if (substr($0,2,1)=="M") print $NF }'
Output indicates files that do not match vendor defaults. After locating a file with incorrect permissions, run the following command to determine which package owns it:
$ rpm -qf FILENAME

Next, run the following command to reset its permissions to the correct values:
$ sudo rpm --setperms PACKAGENAME
Warning:  Profiles may require that specific files have stricter file permissions than defined by the vendor. Such files will be reported as a finding and need to be evaluated according to your policy and deployment environment.
Rationale:
Permissions on system binaries and configuration files that are too generous could allow an unauthorized user to gain privileges that they should not have. The permissions set by the vendor should be maintained. Any deviations from this baseline should be investigated.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_rpm_verify_permissions
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 3, 5, 6, 9, 5.10.4.1, APO01.06, APO11.04, BAI03.05, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.04, DSS05.07, DSS06.02, MEA02.01, 3.3.8, 3.4.1, CCI-001493, CCI-001494, CCI-001495, CCI-001496, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.3.3.9, 4.3.3.5.8, 4.3.3.7.3, 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 5.2, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.5.1, A.12.6.2, A.12.7.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R4.2, CIP-003-8 R6, CIP-007-3 R4, CIP-007-3 R4.1, CIP-007-3 R4.2, CM-6(d), CM-6(c), SI-7, SI-7(1), SI-7(6), AU-9(3), CM-6(a), PR.AC-4, PR.DS-5, PR.IP-1, PR.PT-1, Req-11.5, 11.5.2, SRG-OS-000256-GPOS-00097, SRG-OS-000257-GPOS-00098, SRG-OS-000258-GPOS-00099, SRG-OS-000278-GPOS-00108, 1.7.1.4, 1.7.1.5, 1.7.1.6, 6.1.1, 6.1.2, 6.1.3, 6.1.4, 6.1.5, 6.1.6, 6.1.7, 6.1.8, 6.1.9, SV-204392r880752_rule


Complexity:high
Disruption:medium
Strategy:restrict
- name: Read list of files with incorrect permissions
  command: rpm -Va --nodeps --nosignature --nofiledigest --nosize --nomtime --nordev
    --nocaps --nolinkto --nouser --nogroup
  register: files_with_incorrect_permissions
  failed_when: files_with_incorrect_permissions.rc > 1
  changed_when: false
  check_mode: false
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_permissions

- name: Create list of packages
  command: rpm -qf "{{ item }}"
  with_items: '{{ files_with_incorrect_permissions.stdout_lines | map(''regex_findall'',
    ''^[.]+[M]+.* (\/.*)'', ''\1'') | map(''join'') | select(''match'', ''(\/.*)'')
    | list | unique }}'
  register: list_of_packages
  changed_when: false
  check_mode: false
  when: (files_with_incorrect_permissions.stdout_lines | length > 0)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_permissions

- name: Correct file permissions with RPM
  command: rpm --setperms '{{ item }}'
  with_items: '{{ list_of_packages.results | map(attribute=''stdout_lines'') | list
    | unique }}'
  when: (files_with_incorrect_permissions.stdout_lines | length > 0)
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-010010
  - NIST-800-171-3.3.8
  - NIST-800-171-3.4.1
  - NIST-800-53-AU-9(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-6(c)
  - NIST-800-53-CM-6(d)
  - NIST-800-53-SI-7
  - NIST-800-53-SI-7(1)
  - NIST-800-53-SI-7(6)
  - PCI-DSS-Req-11.5
  - PCI-DSSv4-11.5.2
  - high_complexity
  - high_severity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy
  - rpm_verify_permissions

Complexity:high
Disruption:medium
Strategy:restrict

# Declare array to hold set of RPM packages we need to correct permissions for
declare -A SETPERMS_RPM_DICT

# Create a list of files on the system having permissions different from what
# is expected by the RPM database
readarray -t FILES_WITH_INCORRECT_PERMS < <(rpm -Va --nofiledigest | awk '{ if (substr($0,2,1)=="M") print $NF }')

for FILE_PATH in "${FILES_WITH_INCORRECT_PERMS[@]}"
do
        # NOTE: some files maybe controlled by more then one package
        readarray -t RPM_PACKAGES < <(rpm -qf "${FILE_PATH}")
        for RPM_PACKAGE in "${RPM_PACKAGES[@]}"
        do
                # Use an associative array to store packages as it's keys, not having to care about duplicates.
                SETPERMS_RPM_DICT["$RPM_PACKAGE"]=1
        done
done

# For each of the RPM packages left in the list -- reset its permissions to the
# correct values
for RPM_PACKAGE in "${!SETPERMS_RPM_DICT[@]}"
do
	rpm --restore "${RPM_PACKAGE}"
done
Group   Federal Information Processing Standard (FIPS)   Group contains 1 rule
[ref]   The Federal Information Processing Standard (FIPS) is a computer security standard which is developed by the U.S. Government and industry working groups to validate the quality of cryptographic modules. The FIPS standard provides four security levels to ensure adequate coverage of different industries, implementation of cryptographic modules, and organizational sizes and requirements.

FIPS 140-2 is the current standard for validating that mechanisms used to access cryptographic modules utilize authentication that meets industry and government requirements. For government systems, this allows Security Levels 1, 2, 3, or 4 for use on Red Hat Enterprise Linux 7.

See http://csrc.nist.gov/publications/PubsFIPS.html for more information.

Rule   Enable FIPS Mode in GRUB2   [ref]

To ensure FIPS mode is enabled, install package dracut-fips, and rebuild initramfs by running the following commands:
$ sudo yum install dracut-fips
dracut -f
After the dracut command has been run, add the argument fips=1 to the default GRUB 2 command line for the Linux operating system in /etc/default/grub, in the manner below:
GRUB_CMDLINE_LINUX="crashkernel=auto rd.lvm.lv=VolGroup/LogVol06 rd.lvm.lv=VolGroup/lv_swap rhgb quiet rd.shell=0 fips=1"
Finally, rebuild the grub.cfg file by using the
grub2-mkconfig -o
command as follows:
  • On BIOS-based machines, issue the following command as root:
    ~]# grub2-mkconfig -o /boot/grub2/grub.cfg
  • On UEFI-based machines, issue the following command as root:
    ~]# grub2-mkconfig -o /boot/efi/EFI/redhat/grub.cfg
Warning:  Running
dracut -f
will overwrite the existing initramfs file.
Warning:  The system needs to be rebooted for these changes to take effect.
Warning:  System Crypto Modules must be provided by a vendor that undergoes FIPS-140 certifications. FIPS-140 is applicable to all Federal agencies that use cryptographic-based security systems to protect sensitive information in computer and telecommunication systems (including voice systems) as defined in Section 5131 of the Information Technology Management Reform Act of 1996, Public Law 104-106. This standard shall be used in designing and implementing cryptographic modules that Federal departments and agencies operate or are operated for them under contract. See https://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.140-2.pdf To meet this, the system has to have cryptographic software provided by a vendor that has undergone this certification. This means providing documentation, test results, design information, and independent third party review by an accredited lab. While open source software is capable of meeting this, it does not meet FIPS-140 unless the vendor submits to this process.
Rationale:
Use of weak or untested encryption algorithms undermines the purposes of utilizing encryption to protect data. The operating system must implement cryptographic modules adhering to the higher standards approved by the federal government since this provides assurance they have been tested and validated.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_grub2_enable_fips_mode
Identifiers and References

References:  12, 15, 8, 5.10.1.2, APO13.01, DSS01.04, DSS05.02, DSS05.03, 3.13.8, 3.13.11, CCI-000068, CCI-000803, CCI-001199, CCI-002450, CCI-002476, 4.3.3.6.6, SR 1.13, SR 2.6, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.13.1.1, A.13.2.1, A.14.1.3, A.6.2.1, A.6.2.2, CIP-003-8 R4.2, CIP-007-3 R5.1, SC-12(2), SC-12(3), IA-7, SC-13, CM-6(a), SC-12, PR.AC-3, PR.PT-4, SRG-OS-000033-GPOS-00014, SRG-OS-000185-GPOS-00079, SRG-OS-000396-GPOS-00176, SRG-OS-000405-GPOS-00184, SRG-OS-000478-GPOS-00223, SV-204497r877398_rule



package --add=dracut-fips --add=dracut-fips-aesni

Complexity:high
Disruption:medium
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Check prelink binary installed
  stat:
    path: /usr/sbin/prelink
  register: prelink_exists
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Disable prelink
  lineinfile:
    dest: /etc/sysconfig/prelink
    regexp: ^#?PRELINKING
    line: PRELINKING=no
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - prelink_exists.stat.exists
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Revert prelinking binaries
  command: /usr/sbin/prelink -ua
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - prelink_exists.stat.exists
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Check if system supports AES-NI
  command: grep -q -m1 -o aes /proc/cpuinfo
  failed_when: aesni_supported.rc > 1
  register: aesni_supported
  check_mode: false
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Ensure dracut-fips-aesni is installed
  package:
    name: dracut-fips-aesni
    state: present
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - aesni_supported.rc == 0
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Install dracut-fips
  package:
    name: dracut-fips
    state: present
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Rebuild initramfs
  command: dracut -f
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Check fips argument exists
  command: grep 'GRUB_CMDLINE_LINUX.*fips=' /etc/default/grub
  failed_when: false
  register: fipsargcheck
  check_mode: false
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Replace existing fips argument
  replace:
    path: /etc/default/grub
    regexp: fips=.
    replace: fips=1
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - fipsargcheck.rc == 0
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Add fips argument
  replace:
    path: /etc/default/grub
    regexp: (GRUB_CMDLINE_LINUX=.*)"
    replace: \1 fips=1"
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - fipsargcheck.rc != 0
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Get boot device uuid
  command: findmnt --noheadings --output uuid --target /boot
  register: bootuuid
  check_mode: false
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Check boot argument exists
  command: grep 'GRUB_CMDLINE_LINUX.*boot=' /etc/default/grub
  failed_when: false
  register: bootargcheck
  check_mode: false
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Replace existing boot argument
  replace:
    path: /etc/default/grub
    regexp: boot=\w*-\w*-\w*-\w*-\w*
    replace: boot={{ bootuuid.stdout }}
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - bootargcheck.rc == 0
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Add boot argument
  replace:
    path: /etc/default/grub
    regexp: (GRUB_CMDLINE_LINUX=.*)"
    replace: \1 boot=UUID={{ bootuuid.stdout }}"
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  - bootargcheck.rc != 0
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

- name: Update bootloader menu
  command: /sbin/grubby --update-kernel=ALL --args="fips=1 boot=UUID={{ bootuuid.stdout
    }}"
  when:
  - ( ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
    and not ( lookup("env", "container") == "bwrap-osbuild" ) )
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.10.1.2
  - DISA-STIG-RHEL-07-021350
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - grub2_enable_fips_mode
  - high_complexity
  - high_severity
  - medium_disruption
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if ( [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && ! ( [ "${container:-}" == "bwrap-osbuild" ] ) ) && { rpm --quiet -q grub2-common; }; then

# prelink not installed
if test -e /etc/sysconfig/prelink -o -e /usr/sbin/prelink; then
    if grep -q ^PRELINKING /etc/sysconfig/prelink
    then
        sed -i 's/^PRELINKING[:blank:]*=[:blank:]*[:alpha:]*/PRELINKING=no/' /etc/sysconfig/prelink
    else
        printf '\n' >> /etc/sysconfig/prelink
        printf '%s\n' '# Set PRELINKING=no per security requirements' 'PRELINKING=no' >> /etc/sysconfig/prelink
    fi

    # Undo previous prelink changes to binaries if prelink is available.
    if test -x /usr/sbin/prelink; then
        /usr/sbin/prelink -ua
    fi
fi

if grep -q -m1 -o aes /proc/cpuinfo; then
	if ! rpm -q --quiet "dracut-fips-aesni" ; then
    yum install -y "dracut-fips-aesni"
fi
fi
if ! rpm -q --quiet "dracut-fips" ; then
    yum install -y "dracut-fips"
fi

dracut -f

# Correct the form of default kernel command line in  grub
if grep -q '^GRUB_CMDLINE_LINUX=.*fips=.*"'  /etc/default/grub; then
	# modify the GRUB command-line if a fips= arg already exists
	sed -i 's/\(^GRUB_CMDLINE_LINUX=".*\)fips=[^[:space:]]*\(.*"\)/\1 fips=1 \2/'  /etc/default/grub
else
	# no existing fips=arg is present, append it
	sed -i 's/\(^GRUB_CMDLINE_LINUX=".*\)"/\1 fips=1"/'  /etc/default/grub
fi

# Get the UUID of the device mounted at root (/).
ROOT_UUID=$(findmnt --noheadings --output uuid --target /)

# Get the UUID of the device mounted at /boot.
BOOT_UUID=$(findmnt --noheadings --output uuid --target /boot)

if [ "${ROOT_UUID}" == "${BOOT_UUID}" ]; then
	# root UUID same as boot UUID, so do not modify the GRUB command-line or add boot arg to kernel command line
	# Correct the form of kernel command line for each installed kernel in the bootloader
	/sbin/grubby --update-kernel=ALL --args="fips=1"
else
	# root UUID different from boot UUID, so modify the GRUB command-line and add boot arg to kernel command line
	if grep -q '^GRUB_CMDLINE_LINUX=".*boot=.*"'  /etc/default/grub; then
		# modify the GRUB command-line if a boot= arg already exists
		sed -i 's/\(^GRUB_CMDLINE_LINUX=".*\)boot=[^[:space:]]*\(.*"\)/\1 boot=UUID='"${BOOT_UUID} \2/" /etc/default/grub
	else
		# no existing boot=arg is present, append it
		sed -i 's/\(^GRUB_CMDLINE_LINUX=".*\)"/\1 boot=UUID='${BOOT_UUID}'"/'  /etc/default/grub
	fi
	# Correct the form of kernel command line for each installed kernel in the bootloader
	/sbin/grubby --update-kernel=ALL --args="fips=1 boot=UUID=${BOOT_UUID}"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Operating System Vendor Support and Certification   Group contains 2 rules
[ref]   The assurance of a vendor to provide operating system support and maintenance for their product is an important criterion to ensure product stability and security over the life of the product. A certified product that follows the necessary standards and government certification requirements guarantees that known software vulnerabilities will be remediated, and proper guidance for protecting and securing the operating system will be given.

Rule   The Installed Operating System Is FIPS 140-2 Certified   [ref]

To enable processing of sensitive information the operating system must provide certified cryptographic modules compliant with FIPS 140-2 standard. Red Hat Enterprise Linux is supported by Red Hat, Inc. As the Red Hat Enterprise Linux vendor, Red Hat, Inc. is responsible for maintaining government certifications and standards.
Warning:  There is no remediation besides switching to a different operating system.
Warning:  System Crypto Modules must be provided by a vendor that undergoes FIPS-140 certifications. FIPS-140 is applicable to all Federal agencies that use cryptographic-based security systems to protect sensitive information in computer and telecommunication systems (including voice systems) as defined in Section 5131 of the Information Technology Management Reform Act of 1996, Public Law 104-106. This standard shall be used in designing and implementing cryptographic modules that Federal departments and agencies operate or are operated for them under contract. See https://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.140-2.pdf To meet this, the system has to have cryptographic software provided by a vendor that has undergone this certification. This means providing documentation, test results, design information, and independent third party review by an accredited lab. While open source software is capable of meeting this, it does not meet FIPS-140 unless the vendor submits to this process.
Rationale:
The Federal Information Processing Standard (FIPS) Publication 140-2, (FIPS PUB 140-2) is a computer security standard. The standard specifies security requirements for cryptographic modules used to protect sensitive unclassified information. Refer to the full FIPS 140-2 standard at http://csrc.nist.gov/publications/fips/fips140-2/fips1402.pdf for further details on the requirements. FIPS 140-2 validation is required by U.S. law when information systems use cryptography to protect sensitive government information. In order to achieve FIPS 140-2 certification, cryptographic modules are subject to extensive testing by independent laboratories, accredited by National Institute of Standards and Technology (NIST).
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_installed_OS_is_FIPS_certified
Identifiers and References

References:  CCI-000803, CCI-002450, CIP-003-8 R4.2, CIP-007-3 R5.1, SC-12(2), SC-12(3), IA-7, SC-13, CM-6(a), SC-12

Rule   The Installed Operating System Is Vendor Supported   [ref]

The installed operating system must be maintained by a vendor. Red Hat Enterprise Linux is supported by Red Hat, Inc. As the Red Hat Enterprise Linux vendor, Red Hat, Inc. is responsible for providing security patches.
Warning:  There is no remediation besides switching to a different operating system.
Rationale:
An operating system is considered "supported" if the vendor continues to provide security patches for the product. With an unsupported release, it will not be possible to resolve any security issue discovered in the system software.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_installed_OS_is_vendor_supported
Identifiers and References

References:  18, 20, 4, APO12.01, APO12.02, APO12.03, APO12.04, BAI03.10, DSS05.01, DSS05.02, CCI-000366, 4.2.3, 4.2.3.12, 4.2.3.7, 4.2.3.9, A.12.6.1, A.14.2.3, A.16.1.3, A.18.2.2, A.18.2.3, CM-6(a), MA-6, SA-13(a), ID.RA-1, PR.IP-12, SRG-OS-000480-GPOS-00227, SV-204458r744100_rule

Group   Updating Software   Group contains 5 rules
[ref]   The yum command line tool is used to install and update software packages. The system also provides a graphical software update tool in the System menu, in the Administration submenu, called Software Update.

Red Hat Enterprise Linux 7 systems contain an installed software catalog called the RPM database, which records metadata of installed packages. Consistently using yum or the graphical Software Update for all software installation allows for insight into the current inventory of installed software on the system.

Rule   Ensure yum Removes Previous Package Versions   [ref]

yum should be configured to remove previous software components after new versions have been installed. To configure yum to remove the previous software components after updating, set the clean_requirements_on_remove to 1 in /etc/yum.conf.
Rationale:
Previous versions of software components that are not removed from the information system after updates have been installed may be exploited by some adversaries.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_clean_components_post_updating
Identifiers and References

References:  18, 20, 4, APO12.01, APO12.02, APO12.03, APO12.04, BAI03.10, DSS05.01, DSS05.02, 3.4.8, CCI-002617, 4.2.3, 4.2.3.12, 4.2.3.7, 4.2.3.9, A.12.6.1, A.14.2.3, A.16.1.3, A.18.2.2, A.18.2.3, SI-2(6), CM-11(a), CM-11(b), CM-6(a), ID.RA-1, PR.IP-12, SRG-OS-000437-GPOS-00194, SV-204452r853894_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-020200
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-2(6)
  - clean_components_post_updating
  - low_complexity
  - low_disruption
  - low_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure YUM Removes Previous Package Versions
  lineinfile:
    dest: /etc/yum.conf
    regexp: ^#?clean_requirements_on_remove
    line: clean_requirements_on_remove=1
    insertafter: \[main\]
    create: true
  when: '"yum" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-020200
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-2(6)
  - clean_components_post_updating
  - low_complexity
  - low_disruption
  - low_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q yum; then

if grep --silent ^clean_requirements_on_remove /etc/yum.conf ; then
        sed -i "s/^clean_requirements_on_remove.*/clean_requirements_on_remove=1/g" /etc/yum.conf
else
        echo -e "\n# Set clean_requirements_on_remove to 1 per security requirements" >> /etc/yum.conf
        echo "clean_requirements_on_remove=1" >> /etc/yum.conf
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure gpgcheck Enabled In Main yum Configuration   [ref]

The gpgcheck option controls whether RPM packages' signatures are always checked prior to installation. To configure yum to check package signatures before installing them, ensure the following line appears in /etc/yum.conf in the [main] section:
gpgcheck=1
Rationale:
Changes to any software components can have significant effects on the overall security of the operating system. This requirement ensures the software has not been tampered with and that it has been provided by a trusted vendor.
Accordingly, patches, service packs, device drivers, or operating system components must be signed with a certificate recognized and approved by the organization.
Verifying the authenticity of the software prior to installation validates the integrity of the patch or upgrade received from a vendor. This ensures the software has not been tampered with and that it has been provided by a trusted vendor. Self-signed certificates are disallowed by this requirement. Certificates used to verify the software must be from an approved Certificate Authority (CA).
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_ensure_gpgcheck_globally_activated
Identifiers and References

References:  BP28(R15), 11, 2, 3, 9, 5.10.4.1, APO01.06, BAI03.05, BAI06.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS06.02, 3.4.8, CCI-001749, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.4, SR 3.1, SR 3.3, SR 3.4, SR 3.8, SR 7.6, A.11.2.4, A.12.1.2, A.12.2.1, A.12.5.1, A.12.6.2, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, CM-5(3), SI-7, SC-12, SC-12(3), CM-6(a), SA-12, SA-12(10), CM-11(a), CM-11(b), PR.DS-6, PR.DS-8, PR.IP-1, FPT_TUD_EXT.1, FPT_TUD_EXT.2, Req-6.2, 6.3.3, SRG-OS-000366-GPOS-00153, 1.2.3, SV-204447r877463_rule


Complexity:low
Disruption:medium
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-020050
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - PCI-DSSv4-6.3.3
  - configure_strategy
  - ensure_gpgcheck_globally_activated
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed

- name: Ensure GPG check is globally activated
  ini_file:
    dest: /etc/yum.conf
    section: main
    option: gpgcheck
    value: 1
    no_extra_spaces: true
    create: false
  when: '"yum" in ansible_facts.packages'
  tags:
  - CJIS-5.10.4.1
  - DISA-STIG-RHEL-07-020050
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - PCI-DSSv4-6.3.3
  - configure_strategy
  - ensure_gpgcheck_globally_activated
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if rpm --quiet -q yum; then

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^gpgcheck")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "1"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^gpgcheck\\>" "/etc/yum.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^gpgcheck\\>.*/$escaped_formatted_output/gi" "/etc/yum.conf"
else
    if [[ -s "/etc/yum.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/yum.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/yum.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/yum.conf" >> "/etc/yum.conf"
    printf '%s\n' "$formatted_output" >> "/etc/yum.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure gpgcheck Enabled for Local Packages   [ref]

yum should be configured to verify the signature(s) of local packages prior to installation. To configure yum to verify signatures of local packages, set the localpkg_gpgcheck to 1 in /etc/yum.conf.
Rationale:
Changes to any software components can have significant effects to the overall security of the operating system. This requirement ensures the software has not been tampered and has been provided by a trusted vendor.

Accordingly, patches, service packs, device drivers, or operating system components must be signed with a certificate recognized and approved by the organization.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_ensure_gpgcheck_local_packages
Identifiers and References

References:  BP28(R15), 11, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.4.8, CCI-001749, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, CM-11(a), CM-11(b), CM-6(a), CM-5(3), SA-12, SA-12(10), PR.IP-1, FPT_TUD_EXT.1, FPT_TUD_EXT.2, SRG-OS-000366-GPOS-00153, SV-204448r877463_rule


Complexity:low
Disruption:medium
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-020060
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - ensure_gpgcheck_local_packages
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed
  - unknown_strategy

- name: Ensure GPG check Enabled for Local Packages (yum)
  block:

  - name: Check stats of yum
    stat:
      path: /etc/yum.conf
    register: pkg

  - name: Check if config file of yum is a symlink
    ansible.builtin.set_fact:
      pkg_config_file_symlink: '{{ pkg.stat.lnk_target if pkg.stat.lnk_target is match("^/.*")
        else "/etc/yum.conf" | dirname ~ "/" ~ pkg.stat.lnk_target }}'
    when: pkg.stat.lnk_target is defined

  - name: Ensure GPG check Enabled for Local Packages (yum)
    ini_file:
      dest: '{{ pkg_config_file_symlink |  default("/etc/yum.conf") }}'
      section: main
      option: localpkg_gpgcheck
      value: 1
      no_extra_spaces: true
      create: true
  when: '"yum" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-020060
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - ensure_gpgcheck_local_packages
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed
  - unknown_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q yum; then

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^localpkg_gpgcheck")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "1"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^localpkg_gpgcheck\\>" "/etc/yum.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^localpkg_gpgcheck\\>.*/$escaped_formatted_output/gi" "/etc/yum.conf"
else
    if [[ -s "/etc/yum.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/yum.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/yum.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/yum.conf" >> "/etc/yum.conf"
    printf '%s\n' "$formatted_output" >> "/etc/yum.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure gpgcheck Enabled for All yum Package Repositories   [ref]

To ensure signature checking is not disabled for any repos, remove any lines from files in /etc/yum.repos.d of the form:
gpgcheck=0
Rationale:
Verifying the authenticity of the software prior to installation validates the integrity of the patch or upgrade received from a vendor. This ensures the software has not been tampered with and that it has been provided by a trusted vendor. Self-signed certificates are disallowed by this requirement. Certificates used to verify the software must be from an approved Certificate Authority (CA)."
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_ensure_gpgcheck_never_disabled
Identifiers and References

References:  BP28(R15), 11, 2, 3, 9, 5.10.4.1, APO01.06, BAI03.05, BAI06.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS06.02, 3.4.8, CCI-001749, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.4, SR 3.1, SR 3.3, SR 3.4, SR 3.8, SR 7.6, A.11.2.4, A.12.1.2, A.12.2.1, A.12.5.1, A.12.6.2, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, CM-5(3), SI-7, SC-12, SC-12(3), CM-6(a), SA-12, SA-12(10), CM-11(a), CM-11(b), PR.DS-6, PR.DS-8, PR.IP-1, FPT_TUD_EXT.1, FPT_TUD_EXT.2, Req-6.2, 6.3.3, SRG-OS-000366-GPOS-00153, 1.2.3


Complexity:low
Disruption:medium
Strategy:enable
- name: Grep for yum repo section names
  shell: |
    set -o pipefail
    grep -HEr '^\[.+\]' -r /etc/yum.repos.d/
  register: repo_grep_results
  failed_when: repo_grep_results.rc not in [0, 1]
  changed_when: false
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - PCI-DSSv4-6.3.3
  - enable_strategy
  - ensure_gpgcheck_never_disabled
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed

- name: Set gpgcheck=1 for each yum repo
  ini_file:
    path: '{{ item[0] }}'
    section: '{{ item[1] }}'
    option: gpgcheck
    value: '1'
    no_extra_spaces: true
  loop: '{{ repo_grep_results.stdout | regex_findall( ''(.+\.repo):\[(.+)\]\n?'' )
    }}'
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-11(a)
  - NIST-800-53-CM-11(b)
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SA-12
  - NIST-800-53-SA-12(10)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - PCI-DSSv4-6.3.3
  - enable_strategy
  - ensure_gpgcheck_never_disabled
  - high_severity
  - low_complexity
  - medium_disruption
  - no_reboot_needed


sed -i 's/gpgcheck\s*=.*/gpgcheck=1/g' /etc/yum.repos.d/*

Rule   Ensure Red Hat GPG Key Installed   [ref]

To ensure the system can cryptographically verify base software packages come from Red Hat (and to connect to the Red Hat Network to receive them), the Red Hat GPG key must properly be installed. To install the Red Hat GPG key, run:
$ sudo subscription-manager register
If the system is not connected to the Internet or an RHN Satellite, then install the Red Hat GPG key from trusted media such as the Red Hat installation CD-ROM or DVD. Assuming the disc is mounted in /media/cdrom, use the following command as the root user to import it into the keyring:
$ sudo rpm --import /media/cdrom/RPM-GPG-KEY
Alternatively, the key may be pre-loaded during the RHEL installation. In such cases, the key can be installed by running the following command:
sudo rpm --import /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release
Rationale:
Changes to software components can have significant effects on the overall security of the operating system. This requirement ensures the software has not been tampered with and that it has been provided by a trusted vendor. The Red Hat GPG key is necessary to cryptographically verify packages are from Red Hat.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_ensure_redhat_gpgkey_installed
Identifiers and References

References:  BP28(R15), 11, 2, 3, 9, 5.10.4.1, APO01.06, BAI03.05, BAI06.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS06.02, 3.4.8, CCI-001749, 164.308(a)(1)(ii)(D), 164.312(b), 164.312(c)(1), 164.312(c)(2), 164.312(e)(2)(i), 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.4, SR 3.1, SR 3.3, SR 3.4, SR 3.8, SR 7.6, A.11.2.4, A.12.1.2, A.12.2.1, A.12.5.1, A.12.6.2, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, CIP-003-8 R4.2, CIP-003-8 R6, CIP-007-3 R4, CIP-007-3 R4.1, CIP-007-3 R4.2, CIP-007-3 R5.1, CM-5(3), SI-7, SC-12, SC-12(3), CM-6(a), PR.DS-6, PR.DS-8, PR.IP-1, FPT_TUD_EXT.1, FPT_TUD_EXT.2, Req-6.2, SRG-OS-000366-GPOS-00153, 1.2.3


Complexity:medium
Disruption:medium
Strategy:restrict
- name: Read permission of GPG key directory
  stat:
    path: /etc/pki/rpm-gpg/
  register: gpg_key_directory_permission
  check_mode: false
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - ensure_redhat_gpgkey_installed
  - high_severity
  - medium_complexity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy

- name: Read signatures in GPG key
  command: gpg --with-fingerprint --with-colons "/etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release"
  changed_when: false
  register: gpg_fingerprints
  check_mode: false
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - ensure_redhat_gpgkey_installed
  - high_severity
  - medium_complexity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy

- name: Set Fact - Installed GPG Fingerprints
  set_fact:
    gpg_installed_fingerprints: |-
      {{ gpg_fingerprints.stdout | regex_findall('^pub.*
      (?:^fpr[:]*)([0-9A-Fa-f]*)', '\1') | list }}
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - ensure_redhat_gpgkey_installed
  - high_severity
  - medium_complexity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy

- name: Set Fact - Valid fingerprints
  set_fact:
    gpg_valid_fingerprints: ("567E347AD0044ADE55BA8A5F199E2F91FD431D51" "43A6E49C4A38F4BE9ABF2A5345689C882FA658E0")
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - ensure_redhat_gpgkey_installed
  - high_severity
  - medium_complexity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy

- name: Import RedHat GPG key
  rpm_key:
    state: present
    key: /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release
  when:
  - gpg_key_directory_permission.stat.mode <= '0755'
  - (gpg_installed_fingerprints | difference(gpg_valid_fingerprints)) | length ==
    0
  - gpg_installed_fingerprints | length > 0
  - ansible_distribution == "RedHat"
  tags:
  - CJIS-5.10.4.1
  - NIST-800-171-3.4.8
  - NIST-800-53-CM-5(3)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SI-7
  - PCI-DSS-Req-6.2
  - ensure_redhat_gpgkey_installed
  - high_severity
  - medium_complexity
  - medium_disruption
  - no_reboot_needed
  - restrict_strategy

# The two fingerprints below are retrieved from https://access.redhat.com/security/team/key
readonly REDHAT_RELEASE_FINGERPRINT="567E347AD0044ADE55BA8A5F199E2F91FD431D51"
readonly REDHAT_AUXILIARY_FINGERPRINT="43A6E49C4A38F4BE9ABF2A5345689C882FA658E0"

# Location of the key we would like to import (once it's integrity verified)
readonly REDHAT_RELEASE_KEY="/etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release"

RPM_GPG_DIR_PERMS=$(stat -c %a "$(dirname "$REDHAT_RELEASE_KEY")")

# Verify /etc/pki/rpm-gpg directory permissions are safe
if [ "${RPM_GPG_DIR_PERMS}" -le "755" ]
then
  # If they are safe, try to obtain fingerprints from the key file
  # (to ensure there won't be e.g. CRC error).

  readarray -t GPG_OUT < <(gpg --with-fingerprint --with-colons "$REDHAT_RELEASE_KEY" | grep "^fpr" | cut -d ":" -f 10)

  GPG_RESULT=$?
  # No CRC error, safe to proceed
  if [ "${GPG_RESULT}" -eq "0" ]
  then
    echo "${GPG_OUT[*]}" | grep -vE "${REDHAT_RELEASE_FINGERPRINT}|${REDHAT_AUXILIARY_FINGERPRINT}" || {
      # If $REDHAT_RELEASE_KEY file doesn't contain any keys with unknown fingerprint, import it
      rpm --import "${REDHAT_RELEASE_KEY}"
    }
  fi
fi
Group   Account and Access Control   Group contains 14 groups and 34 rules
[ref]   In traditional Unix security, if an attacker gains shell access to a certain login account, they can perform any action or access any file to which that account has access. Therefore, making it more difficult for unauthorized people to gain shell access to accounts, particularly to privileged accounts, is a necessary part of securing a system. This section introduces mechanisms for restricting access to accounts under Red Hat Enterprise Linux 7.
Group   Warning Banners for System Accesses   Group contains 1 rule
[ref]   Each system should expose as little information about itself as possible.

System banners, which are typically displayed just before a login prompt, give out information about the service or the host's operating system. This might include the distribution name and the system kernel version, and the particular version of a network service. This information can assist intruders in gaining access to the system as it can reveal whether the system is running vulnerable software. Most network services can be configured to limit what information is displayed.

Many organizations implement security policies that require a system banner provide notice of the system's ownership, provide warning to unauthorized users, and remind authorized users of their consent to monitoring.

Rule   Modify the System Login Banner   [ref]

To configure the system login banner edit /etc/issue. Replace the default text with a message compliant with the local site policy or a legal disclaimer. The DoD required text is either:

You are accessing a U.S. Government (USG) Information System (IS) that is provided for USG-authorized use only. By using this IS (which includes any device attached to this IS), you consent to the following conditions:
-The USG routinely intercepts and monitors communications on this IS for purposes including, but not limited to, penetration testing, COMSEC monitoring, network operations and defense, personnel misconduct (PM), law enforcement (LE), and counterintelligence (CI) investigations.
-At any time, the USG may inspect and seize data stored on this IS.
-Communications using, or data stored on, this IS are not private, are subject to routine monitoring, interception, and search, and may be disclosed or used for any USG-authorized purpose.
-This IS includes security measures (e.g., authentication and access controls) to protect USG interests -- not for your personal benefit or privacy.
-Notwithstanding the above, using this IS does not constitute consent to PM, LE or CI investigative searching or monitoring of the content of privileged communications, or work product, related to personal representation or services by attorneys, psychotherapists, or clergy, and their assistants. Such communications and work product are private and confidential. See User Agreement for details.


OR:

I've read & consent to terms in IS user agreem't.
Rationale:
Display of a standardized and approved use notification before granting access to the operating system ensures privacy and security notification verbiage used is consistent with applicable federal laws, Executive Orders, directives, policies, regulations, standards, and guidance.

System use notifications are required only for access via login interfaces with human users and are not required when such human interfaces do not exist.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_banner_etc_issue
Identifiers and References

References:  1, 12, 15, 16, DSS05.04, DSS05.10, DSS06.10, 3.1.9, CCI-000048, CCI-000050, CCI-001384, CCI-001385, CCI-001386, CCI-001387, CCI-001388, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, AC-8(a), AC-8(c), PR.AC-7, FMT_MOF_EXT.1, SRG-OS-000023-GPOS-00006, SRG-OS-000228-GPOS-00088, 1.7.2, SV-204395r603261_rule


Complexity:low
Disruption:medium
- name: XCCDF Value login_banner_text # promote to variable
  set_fact:
    login_banner_text: !!str ^Authorized[\s\n]+uses[\s\n]+only\.[\s\n]+All[\s\n]+activity[\s\n]+may[\s\n]+be[\s\n]+monitored[\s\n]+and[\s\n]+reported\.$
  tags:
    - always

- name: Modify the System Login Banner - ensure correct banner
  copy:
    dest: /etc/issue
    content: '{{ login_banner_text | regex_replace("^\^(.*)\$$", "\1") | regex_replace("^\((.*\.)\|.*\)$",
      "\1") | regex_replace("\[\\s\\n\]\+"," ") | regex_replace("\(\?:\[\\n\]\+\|\(\?:\\\\n\)\+\)",
      "\n") | regex_replace("\\", "") | wordwrap() }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-010050
  - NIST-800-171-3.1.9
  - NIST-800-53-AC-8(a)
  - NIST-800-53-AC-8(c)
  - banner_etc_issue
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - unknown_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

login_banner_text='^Authorized[\s\n]+uses[\s\n]+only\.[\s\n]+All[\s\n]+activity[\s\n]+may[\s\n]+be[\s\n]+monitored[\s\n]+and[\s\n]+reported\.$'


# Multiple regexes transform the banner regex into a usable banner
# 0 - Remove anchors around the banner text
login_banner_text=$(echo "$login_banner_text" | sed 's/^\^\(.*\)\$$/\1/g')
# 1 - Keep only the first banners if there are multiple
#    (dod_banners contains the long and short banner)
login_banner_text=$(echo "$login_banner_text" | sed 's/^(\(.*\.\)|.*)$/\1/g')
# 2 - Add spaces ' '. (Transforms regex for "space or newline" into a " ")
login_banner_text=$(echo "$login_banner_text" | sed 's/\[\\s\\n\]+/ /g')
# 3 - Adds newlines. (Transforms "(?:\[\\n\]+|(?:\\n)+)" into "\n")
login_banner_text=$(echo "$login_banner_text" | sed 's/(?:\[\\n\]+|(?:\\\\n)+)/\n/g')
# 4 - Remove any leftover backslash. (From any parethesis in the banner, for example).
login_banner_text=$(echo "$login_banner_text" | sed 's/\\//g')
formatted=$(echo "$login_banner_text" | fold -sw 80)

cat <<EOF >/etc/issue
$formatted
EOF

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Protect Accounts by Configuring PAM   Group contains 4 groups and 16 rules
[ref]   PAM, or Pluggable Authentication Modules, is a system which implements modular authentication for Linux programs. PAM provides a flexible and configurable architecture for authentication, and it should be configured to minimize exposure to unnecessary risk. This section contains guidance on how to accomplish that.

PAM is implemented as a set of shared objects which are loaded and invoked whenever an application wishes to authenticate a user. Typically, the application must be running as root in order to take advantage of PAM, because PAM's modules often need to be able to access sensitive stores of account information, such as /etc/shadow. Traditional privileged network listeners (e.g. sshd) or SUID programs (e.g. sudo) already meet this requirement. An SUID root application, userhelper, is provided so that programs which are not SUID or privileged themselves can still take advantage of PAM.

PAM looks in the directory /etc/pam.d for application-specific configuration information. For instance, if the program login attempts to authenticate a user, then PAM's libraries follow the instructions in the file /etc/pam.d/login to determine what actions should be taken.

One very important file in /etc/pam.d is /etc/pam.d/system-auth. This file, which is included by many other PAM configuration files, defines 'default' system authentication measures. Modifying this file is a good way to make far-reaching authentication changes, for instance when implementing a centralized authentication service.
Warning:  Be careful when making changes to PAM's configuration files. The syntax for these files is complex, and modifications can have unexpected consequences. The default configurations shipped with applications should be sufficient for most users.
Warning:  Running authconfig or system-config-authentication will re-write the PAM configuration files, destroying any manually made changes and replacing them with a series of system defaults. One reference to the configuration file syntax can be found at https://fossies.org/linux/Linux-PAM-docs/doc/sag/Linux-PAM_SAG.pdf.
Group   Set Lockouts for Failed Password Attempts   Group contains 5 rules
[ref]   The pam_faillock PAM module provides the capability to lock out user accounts after a number of failed login attempts. Its documentation is available in /usr/share/doc/pam-VERSION/txts/README.pam_faillock.

Warning:  Locking out user accounts presents the risk of a denial-of-service attack. The lockout policy must weigh whether the risk of such a denial-of-service attack outweighs the benefits of thwarting password guessing attacks.

Rule   Limit Password Reuse   [ref]

Do not allow users to reuse recent passwords. This can be accomplished by using the remember option for the pam_unix or pam_pwhistory PAM modules.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report.
Warning:  Newer versions of authselect contain an authselect feature to easily and properly enable pam_pwhistory.so module. If this feature is not yet available in your system, an authselect custom profile must be used to avoid integrity issues in PAM files.
Rationale:
Preventing re-use of previous passwords helps ensure that a compromised password is not re-used by a user.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_unix_remember
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, 5.6.2.1.1, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.5.8, CCI-000200, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(f), IA-5(1)(e), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.2.5, 8.3.7, SRG-OS-000077-GPOS-00045, 5.4.4


Complexity:low
Disruption:medium
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
- name: XCCDF Value var_password_pam_unix_remember # promote to variable
  set_fact:
    var_password_pam_unix_remember: !!str 5
  tags:
    - always

- name: Limit Password Reuse - Check if system relies on authselect tool
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - Collect the available authselect features
  ansible.builtin.command:
    cmd: authselect list-features minimal
  register: result_authselect_available_features
  changed_when: false
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - Enable pam_pwhistory.so using authselect feature
  block:

  - name: Limit Password Reuse - Check integrity of authselect current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Limit Password Reuse - Informative message based on the authselect integrity
      check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Limit Password Reuse - Get authselect current features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Limit Password Reuse - Ensure "with-pwhistory" feature is enabled using
      authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature with-pwhistory
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("with-pwhistory")

  - name: Limit Password Reuse - Ensure authselect changes are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  - result_authselect_available_features.stdout is search("with-pwhistory")
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - Enable pam_pwhistory.so in appropriate PAM files
  block:

  - name: Limit Password Reuse - Define the PAM file to be edited as a local fact
    ansible.builtin.set_fact:
      pam_file_path: /etc/pam.d/system-auth

  - name: Limit Password Reuse - Check if system relies on authselect tool
    ansible.builtin.stat:
      path: /usr/bin/authselect
    register: result_authselect_present

  - name: Limit Password Reuse - Ensure authselect custom profile is used if authselect
      is present
    block:

    - name: Limit Password Reuse - Check integrity of authselect current profile
      ansible.builtin.command:
        cmd: authselect check
      register: result_authselect_check_cmd
      changed_when: false
      failed_when: false

    - name: Limit Password Reuse - Informative message based on the authselect integrity
        check result
      ansible.builtin.assert:
        that:
        - result_authselect_check_cmd.rc == 0
        fail_msg:
        - authselect integrity check failed. Remediation aborted!
        - This remediation could not be applied because an authselect profile was
          not selected or the selected profile is not intact.
        - It is not recommended to manually edit the PAM files when authselect tool
          is available.
        - In cases where the default authselect profile does not cover a specific
          demand, a custom authselect profile is recommended.
        success_msg:
        - authselect integrity check passed

    - name: Limit Password Reuse - Get authselect current profile
      ansible.builtin.shell:
        cmd: authselect current -r | awk '{ print $1 }'
      register: result_authselect_profile
      changed_when: false
      when:
      - result_authselect_check_cmd is success

    - name: Limit Password Reuse - Define the current authselect profile as a local
        fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is match("custom/")

    - name: Limit Password Reuse - Define the new authselect custom profile as a local
        fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: custom/hardening
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is not match("custom/")

    - name: Limit Password Reuse - Get authselect current features to also enable
        them in the custom profile
      ansible.builtin.shell:
        cmd: authselect current | tail -n+3 | awk '{ print $2 }'
      register: result_authselect_features
      changed_when: false
      when:
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")

    - name: Limit Password Reuse - Check if any custom profile with the same name
        was already created
      ansible.builtin.stat:
        path: /etc/authselect/{{ authselect_custom_profile }}
      register: result_authselect_custom_profile_present
      changed_when: false
      when:
      - authselect_current_profile is not match("custom/")

    - name: Limit Password Reuse - Create an authselect custom profile based on the
        current profile
      ansible.builtin.command:
        cmd: authselect create-profile hardening -b {{ authselect_current_profile
          }}
      when:
      - result_authselect_check_cmd is success
      - authselect_current_profile is not match("custom/")
      - not result_authselect_custom_profile_present.stat.exists

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Limit Password Reuse - Ensure the authselect custom profile is selected
      ansible.builtin.command:
        cmd: authselect select {{ authselect_custom_profile }}
      register: result_pam_authselect_select_profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Limit Password Reuse - Restore the authselect features in the custom profile
      ansible.builtin.command:
        cmd: authselect enable-feature {{ item }}
      loop: '{{ result_authselect_features.stdout_lines }}'
      register: result_pam_authselect_restore_features
      when:
      - result_authselect_profile is not skipped
      - result_authselect_features is not skipped
      - result_pam_authselect_select_profile is not skipped

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - result_pam_authselect_restore_features is not skipped

    - name: Limit Password Reuse - Change the PAM file to be edited according to the
        custom authselect profile
      ansible.builtin.set_fact:
        pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
          | basename }}
    when:
    - result_authselect_present.stat.exists

  - name: Limit Password Reuse - Check if expected PAM module line is present in {{
      pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      regexp: ^\s*password\s+requisite\s+pam_pwhistory.so\s*.*
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_line_present

  - name: Limit Password Reuse - Include or update the PAM module line in {{ pam_file_path
      }}
    block:

    - name: Limit Password Reuse - Check if required PAM module line is present in
        {{ pam_file_path }} with different control
      ansible.builtin.lineinfile:
        path: '{{ pam_file_path }}'
        regexp: ^\s*password\s+.*\s+pam_pwhistory.so\s*
        state: absent
      check_mode: true
      changed_when: false
      register: result_pam_line_other_control_present

    - name: Limit Password Reuse - Ensure the correct control for the required PAM
        module line in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: ^(\s*password\s+).*(\bpam_pwhistory.so.*)
        replace: \1requisite \2
      register: result_pam_module_edit
      when:
      - result_pam_line_other_control_present.found == 1

    - name: Limit Password Reuse - Ensure the required PAM module line is included
        in {{ pam_file_path }}
      ansible.builtin.lineinfile:
        dest: '{{ pam_file_path }}'
        insertafter: ^password.*requisite.*pam_pwquality\.so
        line: password    requisite    pam_pwhistory.so
      register: result_pam_module_add
      when:
      - result_pam_line_other_control_present.found == 0 or result_pam_line_other_control_present.found
        > 1

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present is defined
      - result_authselect_present.stat.exists
      - |-
        (result_pam_module_add is defined and result_pam_module_add.changed)
         or (result_pam_module_edit is defined and result_pam_module_edit.changed)
    when:
    - result_pam_line_present.found is defined
    - result_pam_line_present.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - |
    (result_authselect_available_features.stdout is defined and result_authselect_available_features.stdout is not search("with-pwhistory")) or result_authselect_available_features is not defined
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - Check the presence of /etc/security/pwhistory.conf
    file
  ansible.builtin.stat:
    path: /etc/security/pwhistory.conf
  register: result_pwhistory_conf_check
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - pam_pwhistory.so parameters are configured in /etc/security/pwhistory.conf
    file
  block:

  - name: Limit Password Reuse - Ensure the pam_pwhistory.so remember parameter in
      /etc/security/pwhistory.conf
    ansible.builtin.lineinfile:
      path: /etc/security/pwhistory.conf
      regexp: ^\s*remember\s*=
      line: remember = {{ var_password_pam_unix_remember }}
      state: present

  - name: Limit Password Reuse - Ensure the pam_pwhistory.so remember parameter is
      removed from PAM files
    block:

    - name: Limit Password Reuse - Check if /etc/pam.d/system-auth file is present
      ansible.builtin.stat:
        path: /etc/pam.d/system-auth
      register: result_pam_file_present

    - name: Limit Password Reuse - Check the proper remediation for the system
      block:

      - name: Limit Password Reuse - Define the PAM file to be edited as a local fact
        ansible.builtin.set_fact:
          pam_file_path: /etc/pam.d/system-auth

      - name: Limit Password Reuse - Check if system relies on authselect tool
        ansible.builtin.stat:
          path: /usr/bin/authselect
        register: result_authselect_present

      - name: Limit Password Reuse - Ensure authselect custom profile is used if authselect
          is present
        block:

        - name: Limit Password Reuse - Check integrity of authselect current profile
          ansible.builtin.command:
            cmd: authselect check
          register: result_authselect_check_cmd
          changed_when: false
          failed_when: false

        - name: Limit Password Reuse - Informative message based on the authselect
            integrity check result
          ansible.builtin.assert:
            that:
            - result_authselect_check_cmd.rc == 0
            fail_msg:
            - authselect integrity check failed. Remediation aborted!
            - This remediation could not be applied because an authselect profile
              was not selected or the selected profile is not intact.
            - It is not recommended to manually edit the PAM files when authselect
              tool is available.
            - In cases where the default authselect profile does not cover a specific
              demand, a custom authselect profile is recommended.
            success_msg:
            - authselect integrity check passed

        - name: Limit Password Reuse - Get authselect current profile
          ansible.builtin.shell:
            cmd: authselect current -r | awk '{ print $1 }'
          register: result_authselect_profile
          changed_when: false
          when:
          - result_authselect_check_cmd is success

        - name: Limit Password Reuse - Define the current authselect profile as a
            local fact
          ansible.builtin.set_fact:
            authselect_current_profile: '{{ result_authselect_profile.stdout }}'
            authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
          when:
          - result_authselect_profile is not skipped
          - result_authselect_profile.stdout is match("custom/")

        - name: Limit Password Reuse - Define the new authselect custom profile as
            a local fact
          ansible.builtin.set_fact:
            authselect_current_profile: '{{ result_authselect_profile.stdout }}'
            authselect_custom_profile: custom/hardening
          when:
          - result_authselect_profile is not skipped
          - result_authselect_profile.stdout is not match("custom/")

        - name: Limit Password Reuse - Get authselect current features to also enable
            them in the custom profile
          ansible.builtin.shell:
            cmd: authselect current | tail -n+3 | awk '{ print $2 }'
          register: result_authselect_features
          changed_when: false
          when:
          - result_authselect_profile is not skipped
          - authselect_current_profile is not match("custom/")

        - name: Limit Password Reuse - Check if any custom profile with the same name
            was already created
          ansible.builtin.stat:
            path: /etc/authselect/{{ authselect_custom_profile }}
          register: result_authselect_custom_profile_present
          changed_when: false
          when:
          - authselect_current_profile is not match("custom/")

        - name: Limit Password Reuse - Create an authselect custom profile based on
            the current profile
          ansible.builtin.command:
            cmd: authselect create-profile hardening -b {{ authselect_current_profile
              }}
          when:
          - result_authselect_check_cmd is success
          - authselect_current_profile is not match("custom/")
          - not result_authselect_custom_profile_present.stat.exists

        - name: Limit Password Reuse - Ensure authselect changes are applied
          ansible.builtin.command:
            cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
          when:
          - result_authselect_check_cmd is success
          - result_authselect_profile is not skipped
          - authselect_current_profile is not match("custom/")
          - authselect_custom_profile is not match(authselect_current_profile)

        - name: Limit Password Reuse - Ensure the authselect custom profile is selected
          ansible.builtin.command:
            cmd: authselect select {{ authselect_custom_profile }}
          register: result_pam_authselect_select_profile
          when:
          - result_authselect_check_cmd is success
          - result_authselect_profile is not skipped
          - authselect_current_profile is not match("custom/")
          - authselect_custom_profile is not match(authselect_current_profile)

        - name: Limit Password Reuse - Restore the authselect features in the custom
            profile
          ansible.builtin.command:
            cmd: authselect enable-feature {{ item }}
          loop: '{{ result_authselect_features.stdout_lines }}'
          register: result_pam_authselect_restore_features
          when:
          - result_authselect_profile is not skipped
          - result_authselect_features is not skipped
          - result_pam_authselect_select_profile is not skipped

        - name: Limit Password Reuse - Ensure authselect changes are applied
          ansible.builtin.command:
            cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
          when:
          - result_authselect_check_cmd is success
          - result_authselect_profile is not skipped
          - result_pam_authselect_restore_features is not skipped

        - name: Limit Password Reuse - Change the PAM file to be edited according
            to the custom authselect profile
          ansible.builtin.set_fact:
            pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
              | basename }}
        when:
        - result_authselect_present.stat.exists

      - name: Limit Password Reuse - Ensure the "remember" option from "pam_pwhistory.so"
          is not present in {{ pam_file_path }}
        ansible.builtin.replace:
          dest: '{{ pam_file_path }}'
          regexp: (.*password.*pam_pwhistory.so.*)\bremember\b=?[0-9a-zA-Z]*(.*)
          replace: \1\2
        register: result_pam_option_removal

      - name: Limit Password Reuse - Ensure authselect changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b
        when:
        - result_authselect_present.stat.exists
        - result_pam_option_removal is changed
      when:
      - result_pam_file_present.stat.exists
  when:
  - '"pam" in ansible_facts.packages'
  - result_pwhistory_conf_check.stat.exists
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

- name: Limit Password Reuse - pam_pwhistory.so parameters are configured in PAM files
  block:

  - name: Limit Password Reuse - Define the PAM file to be edited as a local fact
    ansible.builtin.set_fact:
      pam_file_path: /etc/pam.d/system-auth

  - name: Limit Password Reuse - Check if system relies on authselect tool
    ansible.builtin.stat:
      path: /usr/bin/authselect
    register: result_authselect_present

  - name: Limit Password Reuse - Ensure authselect custom profile is used if authselect
      is present
    block:

    - name: Limit Password Reuse - Check integrity of authselect current profile
      ansible.builtin.command:
        cmd: authselect check
      register: result_authselect_check_cmd
      changed_when: false
      failed_when: false

    - name: Limit Password Reuse - Informative message based on the authselect integrity
        check result
      ansible.builtin.assert:
        that:
        - result_authselect_check_cmd.rc == 0
        fail_msg:
        - authselect integrity check failed. Remediation aborted!
        - This remediation could not be applied because an authselect profile was
          not selected or the selected profile is not intact.
        - It is not recommended to manually edit the PAM files when authselect tool
          is available.
        - In cases where the default authselect profile does not cover a specific
          demand, a custom authselect profile is recommended.
        success_msg:
        - authselect integrity check passed

    - name: Limit Password Reuse - Get authselect current profile
      ansible.builtin.shell:
        cmd: authselect current -r | awk '{ print $1 }'
      register: result_authselect_profile
      changed_when: false
      when:
      - result_authselect_check_cmd is success

    - name: Limit Password Reuse - Define the current authselect profile as a local
        fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is match("custom/")

    - name: Limit Password Reuse - Define the new authselect custom profile as a local
        fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: custom/hardening
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is not match("custom/")

    - name: Limit Password Reuse - Get authselect current features to also enable
        them in the custom profile
      ansible.builtin.shell:
        cmd: authselect current | tail -n+3 | awk '{ print $2 }'
      register: result_authselect_features
      changed_when: false
      when:
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")

    - name: Limit Password Reuse - Check if any custom profile with the same name
        was already created
      ansible.builtin.stat:
        path: /etc/authselect/{{ authselect_custom_profile }}
      register: result_authselect_custom_profile_present
      changed_when: false
      when:
      - authselect_current_profile is not match("custom/")

    - name: Limit Password Reuse - Create an authselect custom profile based on the
        current profile
      ansible.builtin.command:
        cmd: authselect create-profile hardening -b {{ authselect_current_profile
          }}
      when:
      - result_authselect_check_cmd is success
      - authselect_current_profile is not match("custom/")
      - not result_authselect_custom_profile_present.stat.exists

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Limit Password Reuse - Ensure the authselect custom profile is selected
      ansible.builtin.command:
        cmd: authselect select {{ authselect_custom_profile }}
      register: result_pam_authselect_select_profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Limit Password Reuse - Restore the authselect features in the custom profile
      ansible.builtin.command:
        cmd: authselect enable-feature {{ item }}
      loop: '{{ result_authselect_features.stdout_lines }}'
      register: result_pam_authselect_restore_features
      when:
      - result_authselect_profile is not skipped
      - result_authselect_features is not skipped
      - result_pam_authselect_select_profile is not skipped

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - result_pam_authselect_restore_features is not skipped

    - name: Limit Password Reuse - Change the PAM file to be edited according to the
        custom authselect profile
      ansible.builtin.set_fact:
        pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
          | basename }}
    when:
    - result_authselect_present.stat.exists

  - name: Limit Password Reuse - Check if expected PAM module line is present in {{
      pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      regexp: ^\s*password\s+requisite\s+pam_pwhistory.so\s*.*
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_line_present

  - name: Limit Password Reuse - Include or update the PAM module line in {{ pam_file_path
      }}
    block:

    - name: Limit Password Reuse - Check if required PAM module line is present in
        {{ pam_file_path }} with different control
      ansible.builtin.lineinfile:
        path: '{{ pam_file_path }}'
        regexp: ^\s*password\s+.*\s+pam_pwhistory.so\s*
        state: absent
      check_mode: true
      changed_when: false
      register: result_pam_line_other_control_present

    - name: Limit Password Reuse - Ensure the correct control for the required PAM
        module line in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: ^(\s*password\s+).*(\bpam_pwhistory.so.*)
        replace: \1requisite \2
      register: result_pam_module_edit
      when:
      - result_pam_line_other_control_present.found == 1

    - name: Limit Password Reuse - Ensure the required PAM module line is included
        in {{ pam_file_path }}
      ansible.builtin.lineinfile:
        dest: '{{ pam_file_path }}'
        line: password    requisite    pam_pwhistory.so
      register: result_pam_module_add
      when:
      - result_pam_line_other_control_present.found == 0 or result_pam_line_other_control_present.found
        > 1

    - name: Limit Password Reuse - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present is defined
      - result_authselect_present.stat.exists
      - |-
        (result_pam_module_add is defined and result_pam_module_add.changed)
         or (result_pam_module_edit is defined and result_pam_module_edit.changed)
    when:
    - result_pam_line_present.found is defined
    - result_pam_line_present.found == 0

  - name: Limit Password Reuse - Check if the required PAM module option is present
      in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      regexp: ^\s*password\s+requisite\s+pam_pwhistory.so\s*.*\sremember\b
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_module_remember_option_present

  - name: Limit Password Reuse - Ensure the "remember" PAM option for "pam_pwhistory.so"
      is included in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      backrefs: true
      regexp: ^(\s*password\s+requisite\s+pam_pwhistory.so.*)
      line: \1 remember={{ var_password_pam_unix_remember }}
      state: present
    register: result_pam_remember_add
    when:
    - result_pam_module_remember_option_present.found == 0

  - name: Limit Password Reuse - Ensure the required value for "remember" PAM option
      from "pam_pwhistory.so" in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      backrefs: true
      regexp: ^(\s*password\s+requisite\s+pam_pwhistory.so\s+.*)(remember)=[0-9a-zA-Z]+\s*(.*)
      line: \1\2={{ var_password_pam_unix_remember }} \3
    register: result_pam_remember_edit
    when:
    - result_pam_module_remember_option_present.found > 0

  - name: Limit Password Reuse - Ensure authselect changes are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_present.stat.exists
    - (result_pam_remember_add is defined and result_pam_remember_add.changed) or
      (result_pam_remember_edit is defined and result_pam_remember_edit.changed)
  when:
  - '"pam" in ansible_facts.packages'
  - not result_pwhistory_conf_check.stat.exists
  tags:
  - CJIS-5.6.2.1.1
  - NIST-800-171-3.5.8
  - NIST-800-53-IA-5(1)(e)
  - NIST-800-53-IA-5(f)
  - PCI-DSS-Req-8.2.5
  - PCI-DSSv4-8.3.7
  - accounts_password_pam_unix_remember
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_unix_remember='5'


if [ -f /usr/bin/authselect ]; then
    if authselect list-features minimal | grep -q with-pwhistory; then
        if ! authselect check; then
        echo "
        authselect integrity check failed. Remediation aborted!
        This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
        It is not recommended to manually edit the PAM files when authselect tool is available.
        In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
        exit 1
        fi
        authselect enable-feature with-pwhistory

        authselect apply-changes -b
    else
        
        if ! authselect check; then
        echo "
        authselect integrity check failed. Remediation aborted!
        This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
        It is not recommended to manually edit the PAM files when authselect tool is available.
        In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
        exit 1
        fi

        CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
        # If not already in use, a custom profile is created preserving the enabled features.
        if [[ ! $CURRENT_PROFILE == custom/* ]]; then
            ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
            authselect create-profile hardening -b $CURRENT_PROFILE
            CURRENT_PROFILE="custom/hardening"
            
            authselect apply-changes -b --backup=before-hardening-custom-profile
            authselect select $CURRENT_PROFILE
            for feature in $ENABLED_FEATURES; do
                authselect enable-feature $feature;
            done
            
            authselect apply-changes -b --backup=after-hardening-custom-profile
        fi
        PAM_FILE_NAME=$(basename "/etc/pam.d/system-auth")
        PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

        authselect apply-changes -b
        if ! grep -qP '^\s*password\s+'"requisite"'\s+pam_pwhistory.so\s*.*' "$PAM_FILE_PATH"; then
            # Line matching group + control + module was not found. Check group + module.
            if [ "$(grep -cP '^\s*password\s+.*\s+pam_pwhistory.so\s*' "$PAM_FILE_PATH")" -eq 1 ]; then
                # The control is updated only if one single line matches.
                sed -i -E --follow-symlinks 's/^(\s*password\s+).*(\bpam_pwhistory.so.*)/\1'"requisite"' \2/' "$PAM_FILE_PATH"
            else
                LAST_MATCH_LINE=$(grep -nP "^password.*requisite.*pam_pwquality\.so" "$PAM_FILE_PATH" | tail -n 1 | cut -d: -f 1)
                if [ ! -z $LAST_MATCH_LINE ]; then
                    sed -i --follow-symlinks $LAST_MATCH_LINE' a password     '"requisite"'    pam_pwhistory.so' "$PAM_FILE_PATH"
                else
                    echo 'password    '"requisite"'    pam_pwhistory.so' >> "$PAM_FILE_PATH"
                fi
            fi
        fi
    fi
else
    if ! grep -qP '^\s*password\s+'"requisite"'\s+pam_pwhistory.so\s*.*' "/etc/pam.d/system-auth"; then
        # Line matching group + control + module was not found. Check group + module.
        if [ "$(grep -cP '^\s*password\s+.*\s+pam_pwhistory.so\s*' "/etc/pam.d/system-auth")" -eq 1 ]; then
            # The control is updated only if one single line matches.
            sed -i -E --follow-symlinks 's/^(\s*password\s+).*(\bpam_pwhistory.so.*)/\1'"requisite"' \2/' "/etc/pam.d/system-auth"
        else
            LAST_MATCH_LINE=$(grep -nP "^password.*requisite.*pam_pwquality\.so" "/etc/pam.d/system-auth" | tail -n 1 | cut -d: -f 1)
            if [ ! -z $LAST_MATCH_LINE ]; then
                sed -i --follow-symlinks $LAST_MATCH_LINE' a password     '"requisite"'    pam_pwhistory.so' "/etc/pam.d/system-auth"
            else
                echo 'password    '"requisite"'    pam_pwhistory.so' >> "/etc/pam.d/system-auth"
            fi
        fi
    fi
fi

PWHISTORY_CONF="/etc/security/pwhistory.conf"
if [ -f $PWHISTORY_CONF ]; then
    regex="^\s*remember\s*="
    line="remember = $var_password_pam_unix_remember"
    if ! grep -q $regex $PWHISTORY_CONF; then
        echo $line >> $PWHISTORY_CONF
    else
        sed -i --follow-symlinks 's|^\s*\(remember\s*=\s*\)\(\S\+\)|\1'"$var_password_pam_unix_remember"'|g' $PWHISTORY_CONF
    fi
    if [ -e "/etc/pam.d/system-auth" ] ; then
        PAM_FILE_PATH="/etc/pam.d/system-auth"
        if [ -f /usr/bin/authselect ]; then
            
            if ! authselect check; then
            echo "
            authselect integrity check failed. Remediation aborted!
            This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
            It is not recommended to manually edit the PAM files when authselect tool is available.
            In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
            exit 1
            fi

            CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
            # If not already in use, a custom profile is created preserving the enabled features.
            if [[ ! $CURRENT_PROFILE == custom/* ]]; then
                ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
                authselect create-profile hardening -b $CURRENT_PROFILE
                CURRENT_PROFILE="custom/hardening"
                
                authselect apply-changes -b --backup=before-hardening-custom-profile
                authselect select $CURRENT_PROFILE
                for feature in $ENABLED_FEATURES; do
                    authselect enable-feature $feature;
                done
                
                authselect apply-changes -b --backup=after-hardening-custom-profile
            fi
            PAM_FILE_NAME=$(basename "/etc/pam.d/system-auth")
            PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

            authselect apply-changes -b
        fi
        
    if grep -qP '^\s*password\s.*\bpam_pwhistory.so\s.*\bremember\b' "$PAM_FILE_PATH"; then
        sed -i -E --follow-symlinks 's/(.*password.*pam_pwhistory.so.*)\bremember\b=?[[:alnum:]]*(.*)/\1\2/g' "$PAM_FILE_PATH"
    fi
        if [ -f /usr/bin/authselect ]; then
            
            authselect apply-changes -b
        fi
    else
        echo "/etc/pam.d/system-auth was not found" >&2
    fi
else
    PAM_FILE_PATH="/etc/pam.d/system-auth"
    if [ -f /usr/bin/authselect ]; then
        
        if ! authselect check; then
        echo "
        authselect integrity check failed. Remediation aborted!
        This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
        It is not recommended to manually edit the PAM files when authselect tool is available.
        In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
        exit 1
        fi

        CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
        # If not already in use, a custom profile is created preserving the enabled features.
        if [[ ! $CURRENT_PROFILE == custom/* ]]; then
            ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
            authselect create-profile hardening -b $CURRENT_PROFILE
            CURRENT_PROFILE="custom/hardening"
            
            authselect apply-changes -b --backup=before-hardening-custom-profile
            authselect select $CURRENT_PROFILE
            for feature in $ENABLED_FEATURES; do
                authselect enable-feature $feature;
            done
            
            authselect apply-changes -b --backup=after-hardening-custom-profile
        fi
        PAM_FILE_NAME=$(basename "/etc/pam.d/system-auth")
        PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

        authselect apply-changes -b
    fi
    if ! grep -qP '^\s*password\s+'"requisite"'\s+pam_pwhistory.so\s*.*' "$PAM_FILE_PATH"; then
        # Line matching group + control + module was not found. Check group + module.
        if [ "$(grep -cP '^\s*password\s+.*\s+pam_pwhistory.so\s*' "$PAM_FILE_PATH")" -eq 1 ]; then
            # The control is updated only if one single line matches.
            sed -i -E --follow-symlinks 's/^(\s*password\s+).*(\bpam_pwhistory.so.*)/\1'"requisite"' \2/' "$PAM_FILE_PATH"
        else
            echo 'password    '"requisite"'    pam_pwhistory.so' >> "$PAM_FILE_PATH"
        fi
    fi
    # Check the option
    if ! grep -qP '^\s*password\s+'"requisite"'\s+pam_pwhistory.so\s*.*\sremember\b' "$PAM_FILE_PATH"; then
        sed -i -E --follow-symlinks '/\s*password\s+'"requisite"'\s+pam_pwhistory.so.*/ s/$/ remember='"$var_password_pam_unix_remember"'/' "$PAM_FILE_PATH"
    else
        sed -i -E --follow-symlinks 's/(\s*password\s+'"requisite"'\s+pam_pwhistory.so\s+.*)('"remember"'=)[[:alnum:]]+\s*(.*)/\1\2'"$var_password_pam_unix_remember"' \3/' "$PAM_FILE_PATH"
    fi
    if [ -f /usr/bin/authselect ]; then
        
        authselect apply-changes -b
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Lock Accounts After Failed Password Attempts   [ref]

This rule configures the system to lock out accounts after a number of incorrect login attempts using pam_faillock.so. pam_faillock.so module requires multiple entries in pam files. These entries must be carefully defined to work as expected. In order to avoid errors when manually editing these files, it is recommended to use the appropriate tools, such as authselect or authconfig, depending on the OS version.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report. If the system supports the /etc/security/faillock.conf file, the pam_faillock parameters should be defined in faillock.conf file.
Rationale:
By limiting the number of failed logon attempts, the risk of unauthorized system access via user password guessing, also known as brute-forcing, is reduced. Limits are imposed by locking the account.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_passwords_pam_faillock_deny
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5.5.3, DSS05.04, DSS05.10, DSS06.10, 3.1.8, CCI-000044, CCI-002236, CCI-002237, CCI-002238, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, CM-6(a), AC-7(a), PR.AC-7, FIA_AFL.1, Req-8.1.6, 8.3.4, SRG-OS-000329-GPOS-00128, SRG-OS-000021-GPOS-00005, 5.3.2, SV-204427r880842_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Check if system relies on authselect
    tool
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Remediation where authselect
    tool is present
  block:

  - name: Lock Accounts After Failed Password Attempts - Check integrity of authselect
      current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Lock Accounts After Failed Password Attempts - Informative message based
      on the authselect integrity check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Lock Accounts After Failed Password Attempts - Get authselect current features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Lock Accounts After Failed Password Attempts - Ensure "with-faillock" feature
      is enabled using authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature with-faillock
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("with-faillock")

  - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
      are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Remediation where authselect
    tool is not present
  block:

  - name: Lock Accounts After Failed Password Attempts - Check if pam_faillock.so
      is already enabled
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail)
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_is_enabled

  - name: Lock Accounts After Failed Password Attempts - Enable pam_faillock.so preauth
      editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so preauth
      insertbefore: ^auth.*sufficient.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Lock Accounts After Failed Password Attempts - Enable pam_faillock.so authfail
      editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so authfail
      insertbefore: ^auth.*required.*pam_deny\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Lock Accounts After Failed Password Attempts - Enable pam_faillock.so account
      section editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: account     required      pam_faillock.so
      insertbefore: ^account.*required.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_accounts_passwords_pam_faillock_deny # promote to variable
  set_fact:
    var_accounts_passwords_pam_faillock_deny: !!str 3
  tags:
    - always

- name: Lock Accounts After Failed Password Attempts - Check the presence of /etc/security/faillock.conf
    file
  ansible.builtin.stat:
    path: /etc/security/faillock.conf
  register: result_faillock_conf_check
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Ensure the pam_faillock.so
    deny parameter in /etc/security/faillock.conf
  ansible.builtin.lineinfile:
    path: /etc/security/faillock.conf
    regexp: ^\s*deny\s*=
    line: deny = {{ var_accounts_passwords_pam_faillock_deny }}
    state: present
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Ensure the pam_faillock.so
    deny parameter not in PAM files
  block:

  - name: Lock Accounts After Failed Password Attempts - Check if /etc/pam.d/system-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/system-auth
    register: result_pam_file_present

  - name: Lock Accounts After Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Lock Accounts After Failed Password Attempts - Define the PAM file to
        be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/system-auth

    - name: Lock Accounts After Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Lock Accounts After Failed Password Attempts - Ensure authselect custom
        profile is used if authselect is present
      block:

      - name: Lock Accounts After Failed Password Attempts - Check integrity of authselect
          current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Lock Accounts After Failed Password Attempts - Informative message based
          on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Lock Accounts After Failed Password Attempts - Get authselect current
          profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Lock Accounts After Failed Password Attempts - Define the current authselect
          profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Define the new authselect
          custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Get authselect current
          features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Check if any custom profile
          with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Lock Accounts After Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Lock Accounts After Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Lock Accounts After Failed Password Attempts - Change the PAM file to
          be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Lock Accounts After Failed Password Attempts - Ensure the "deny" option
        from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bdeny\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
        are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists

  - name: Lock Accounts After Failed Password Attempts - Check if /etc/pam.d/password-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/password-auth
    register: result_pam_file_present

  - name: Lock Accounts After Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Lock Accounts After Failed Password Attempts - Define the PAM file to
        be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/password-auth

    - name: Lock Accounts After Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Lock Accounts After Failed Password Attempts - Ensure authselect custom
        profile is used if authselect is present
      block:

      - name: Lock Accounts After Failed Password Attempts - Check integrity of authselect
          current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Lock Accounts After Failed Password Attempts - Informative message based
          on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Lock Accounts After Failed Password Attempts - Get authselect current
          profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Lock Accounts After Failed Password Attempts - Define the current authselect
          profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Define the new authselect
          custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Get authselect current
          features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Check if any custom profile
          with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Lock Accounts After Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Lock Accounts After Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Lock Accounts After Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Lock Accounts After Failed Password Attempts - Change the PAM file to
          be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Lock Accounts After Failed Password Attempts - Ensure the "deny" option
        from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bdeny\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Lock Accounts After Failed Password Attempts - Ensure authselect changes
        are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Lock Accounts After Failed Password Attempts - Ensure the pam_faillock.so
    deny parameter in PAM files
  block:

  - name: Lock Accounts After Failed Password Attempts - Check if pam_faillock.so
      deny parameter is already enabled in pam files
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail).*deny
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_deny_parameter_is_present

  - name: Lock Accounts After Failed Password Attempts - Ensure the inclusion of pam_faillock.so
      preauth deny parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)
      line: \1required\3 deny={{ var_accounts_passwords_pam_faillock_deny }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_deny_parameter_is_present.found == 0

  - name: Lock Accounts After Failed Password Attempts - Ensure the inclusion of pam_faillock.so
      authfail deny parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)
      line: \1required\3 deny={{ var_accounts_passwords_pam_faillock_deny }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_deny_parameter_is_present.found == 0

  - name: Lock Accounts After Failed Password Attempts - Ensure the desired value
      for pam_faillock.so preauth deny parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)(deny)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_deny }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_deny_parameter_is_present.found > 0

  - name: Lock Accounts After Failed Password Attempts - Ensure the desired value
      for pam_faillock.so authfail deny parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)(deny)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_deny }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_deny_parameter_is_present.found > 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.6
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_deny
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_accounts_passwords_pam_faillock_deny='3'


if [ -f /usr/bin/authselect ]; then
    if ! authselect check; then
echo "
authselect integrity check failed. Remediation aborted!
This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
It is not recommended to manually edit the PAM files when authselect tool is available.
In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
exit 1
fi
authselect enable-feature with-faillock

authselect apply-changes -b
else
    
AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")
for pam_file in "${AUTH_FILES[@]}"
do
    if ! grep -qE '^\s*auth\s+required\s+pam_faillock\.so\s+(preauth silent|authfail).*$' "$pam_file" ; then
        sed -i --follow-symlinks '/^auth.*sufficient.*pam_unix\.so.*/i auth        required      pam_faillock.so preauth silent' "$pam_file"
        sed -i --follow-symlinks '/^auth.*required.*pam_deny\.so.*/i auth        required      pam_faillock.so authfail' "$pam_file"
        sed -i --follow-symlinks '/^account.*required.*pam_unix\.so.*/i account     required      pam_faillock.so' "$pam_file"
    fi
    sed -Ei 's/(auth.*)(\[default=die\])(.*pam_faillock\.so)/\1required     \3/g' "$pam_file"
done

fi

AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")

FAILLOCK_CONF="/etc/security/faillock.conf"
if [ -f $FAILLOCK_CONF ]; then
    regex="^\s*deny\s*="
    line="deny = $var_accounts_passwords_pam_faillock_deny"
    if ! grep -q $regex $FAILLOCK_CONF; then
        echo $line >> $FAILLOCK_CONF
    else
        sed -i --follow-symlinks 's|^\s*\(deny\s*=\s*\)\(\S\+\)|\1'"$var_accounts_passwords_pam_faillock_deny"'|g' $FAILLOCK_CONF
    fi
    for pam_file in "${AUTH_FILES[@]}"
    do
        if [ -e "$pam_file" ] ; then
            PAM_FILE_PATH="$pam_file"
            if [ -f /usr/bin/authselect ]; then
                
                if ! authselect check; then
                echo "
                authselect integrity check failed. Remediation aborted!
                This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
                It is not recommended to manually edit the PAM files when authselect tool is available.
                In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
                exit 1
                fi

                CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
                # If not already in use, a custom profile is created preserving the enabled features.
                if [[ ! $CURRENT_PROFILE == custom/* ]]; then
                    ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
                    authselect create-profile hardening -b $CURRENT_PROFILE
                    CURRENT_PROFILE="custom/hardening"
                    
                    authselect apply-changes -b --backup=before-hardening-custom-profile
                    authselect select $CURRENT_PROFILE
                    for feature in $ENABLED_FEATURES; do
                        authselect enable-feature $feature;
                    done
                    
                    authselect apply-changes -b --backup=after-hardening-custom-profile
                fi
                PAM_FILE_NAME=$(basename "$pam_file")
                PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

                authselect apply-changes -b
            fi
            
        if grep -qP '^\s*auth\s.*\bpam_faillock.so\s.*\bdeny\b' "$PAM_FILE_PATH"; then
            sed -i -E --follow-symlinks 's/(.*auth.*pam_faillock.so.*)\bdeny\b=?[[:alnum:]]*(.*)/\1\2/g' "$PAM_FILE_PATH"
        fi
            if [ -f /usr/bin/authselect ]; then
                
                authselect apply-changes -b
            fi
        else
            echo "$pam_file was not found" >&2
        fi
    done
else
    for pam_file in "${AUTH_FILES[@]}"
    do
        if ! grep -qE '^\s*auth.*pam_faillock\.so (preauth|authfail).*deny' "$pam_file"; then
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*preauth.*silent.*/ s/$/ deny='"$var_accounts_passwords_pam_faillock_deny"'/' "$pam_file"
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*authfail.*/ s/$/ deny='"$var_accounts_passwords_pam_faillock_deny"'/' "$pam_file"
        else
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*preauth.*silent.*\)\('"deny"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_deny"'\3/' "$pam_file"
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*authfail.*\)\('"deny"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_deny"'\3/' "$pam_file"
        fi
    done
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Configure the root Account for Failed Password Attempts   [ref]

This rule configures the system to lock out the root account after a number of incorrect login attempts using pam_faillock.so. pam_faillock.so module requires multiple entries in pam files. These entries must be carefully defined to work as expected. In order to avoid errors when manually editing these files, it is recommended to use the appropriate tools, such as authselect or authconfig, depending on the OS version.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report. If the system supports the /etc/security/faillock.conf file, the pam_faillock parameters should be defined in faillock.conf file.
Rationale:
By limiting the number of failed logon attempts, the risk of unauthorized system access via user password guessing, also known as brute-forcing, is reduced. Limits are imposed by locking the account.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_passwords_pam_faillock_deny_root
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, DSS05.04, DSS05.10, DSS06.10, CCI-002238, CCI-000044, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, CM-6(a), AC-7(b), IA-5(c), PR.AC-7, FMT_MOF_EXT.1, SRG-OS-000329-GPOS-00128, SRG-OS-000021-GPOS-00005, SV-204428r880845_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Check if system
    relies on authselect tool
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Remediation where
    authselect tool is present
  block:

  - name: Configure the root Account for Failed Password Attempts - Check integrity
      of authselect current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Configure the root Account for Failed Password Attempts - Informative message
      based on the authselect integrity check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Configure the root Account for Failed Password Attempts - Get authselect
      current features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Configure the root Account for Failed Password Attempts - Ensure "with-faillock"
      feature is enabled using authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature with-faillock
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("with-faillock")

  - name: Configure the root Account for Failed Password Attempts - Ensure authselect
      changes are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Remediation where
    authselect tool is not present
  block:

  - name: Configure the root Account for Failed Password Attempts - Check if pam_faillock.so
      is already enabled
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail)
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_is_enabled

  - name: Configure the root Account for Failed Password Attempts - Enable pam_faillock.so
      preauth editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so preauth
      insertbefore: ^auth.*sufficient.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Configure the root Account for Failed Password Attempts - Enable pam_faillock.so
      authfail editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so authfail
      insertbefore: ^auth.*required.*pam_deny\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Configure the root Account for Failed Password Attempts - Enable pam_faillock.so
      account section editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: account     required      pam_faillock.so
      insertbefore: ^account.*required.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_authselect_present.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Check the presence
    of /etc/security/faillock.conf file
  ansible.builtin.stat:
    path: /etc/security/faillock.conf
  register: result_faillock_conf_check
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Ensure the pam_faillock.so
    even_deny_root parameter in /etc/security/faillock.conf
  ansible.builtin.lineinfile:
    path: /etc/security/faillock.conf
    regexp: ^\s*even_deny_root
    line: even_deny_root
    state: present
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Ensure the pam_faillock.so
    even_deny_root parameter not in PAM files
  block:

  - name: Configure the root Account for Failed Password Attempts - Check if /etc/pam.d/system-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/system-auth
    register: result_pam_file_present

  - name: Configure the root Account for Failed Password Attempts - Check the proper
      remediation for the system
    block:

    - name: Configure the root Account for Failed Password Attempts - Define the PAM
        file to be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/system-auth

    - name: Configure the root Account for Failed Password Attempts - Check if system
        relies on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Configure the root Account for Failed Password Attempts - Ensure authselect
        custom profile is used if authselect is present
      block:

      - name: Configure the root Account for Failed Password Attempts - Check integrity
          of authselect current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Configure the root Account for Failed Password Attempts - Informative
          message based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Configure the root Account for Failed Password Attempts - Get authselect
          current profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Configure the root Account for Failed Password Attempts - Define the
          current authselect profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Define the
          new authselect custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Get authselect
          current features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Check if any
          custom profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Create an
          authselect custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Configure the root Account for Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Configure the root Account for Failed Password Attempts - Ensure the
          authselect custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Configure the root Account for Failed Password Attempts - Restore the
          authselect features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Configure the root Account for Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Configure the root Account for Failed Password Attempts - Change the
          PAM file to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Configure the root Account for Failed Password Attempts - Ensure the "even_deny_root"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\beven_deny_root\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Configure the root Account for Failed Password Attempts - Ensure authselect
        changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists

  - name: Configure the root Account for Failed Password Attempts - Check if /etc/pam.d/password-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/password-auth
    register: result_pam_file_present

  - name: Configure the root Account for Failed Password Attempts - Check the proper
      remediation for the system
    block:

    - name: Configure the root Account for Failed Password Attempts - Define the PAM
        file to be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/password-auth

    - name: Configure the root Account for Failed Password Attempts - Check if system
        relies on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Configure the root Account for Failed Password Attempts - Ensure authselect
        custom profile is used if authselect is present
      block:

      - name: Configure the root Account for Failed Password Attempts - Check integrity
          of authselect current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Configure the root Account for Failed Password Attempts - Informative
          message based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Configure the root Account for Failed Password Attempts - Get authselect
          current profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Configure the root Account for Failed Password Attempts - Define the
          current authselect profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Define the
          new authselect custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Get authselect
          current features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Check if any
          custom profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Configure the root Account for Failed Password Attempts - Create an
          authselect custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Configure the root Account for Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Configure the root Account for Failed Password Attempts - Ensure the
          authselect custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Configure the root Account for Failed Password Attempts - Restore the
          authselect features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Configure the root Account for Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Configure the root Account for Failed Password Attempts - Change the
          PAM file to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Configure the root Account for Failed Password Attempts - Ensure the "even_deny_root"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\beven_deny_root\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Configure the root Account for Failed Password Attempts - Ensure authselect
        changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Configure the root Account for Failed Password Attempts - Ensure the pam_faillock.so
    even_deny_root parameter in PAM files
  block:

  - name: Configure the root Account for Failed Password Attempts - Check if pam_faillock.so
      even_deny_root parameter is already enabled in pam files
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail).*even_deny_root
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_even_deny_root_parameter_is_present

  - name: Configure the root Account for Failed Password Attempts - Ensure the inclusion
      of pam_faillock.so preauth even_deny_root parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)
      line: \1required\3 even_deny_root
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_even_deny_root_parameter_is_present.found == 0

  - name: Configure the root Account for Failed Password Attempts - Ensure the inclusion
      of pam_faillock.so authfail even_deny_root parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)
      line: \1required\3 even_deny_root
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_even_deny_root_parameter_is_present.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010330
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(c)
  - accounts_passwords_pam_faillock_deny_root
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

if [ -f /usr/bin/authselect ]; then
    if ! authselect check; then
echo "
authselect integrity check failed. Remediation aborted!
This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
It is not recommended to manually edit the PAM files when authselect tool is available.
In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
exit 1
fi
authselect enable-feature with-faillock

authselect apply-changes -b
else
    
AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")
for pam_file in "${AUTH_FILES[@]}"
do
    if ! grep -qE '^\s*auth\s+required\s+pam_faillock\.so\s+(preauth silent|authfail).*$' "$pam_file" ; then
        sed -i --follow-symlinks '/^auth.*sufficient.*pam_unix\.so.*/i auth        required      pam_faillock.so preauth silent' "$pam_file"
        sed -i --follow-symlinks '/^auth.*required.*pam_deny\.so.*/i auth        required      pam_faillock.so authfail' "$pam_file"
        sed -i --follow-symlinks '/^account.*required.*pam_unix\.so.*/i account     required      pam_faillock.so' "$pam_file"
    fi
    sed -Ei 's/(auth.*)(\[default=die\])(.*pam_faillock\.so)/\1required     \3/g' "$pam_file"
done

fi

AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")

FAILLOCK_CONF="/etc/security/faillock.conf"
if [ -f $FAILLOCK_CONF ]; then
    regex="^\s*even_deny_root"
    line="even_deny_root"
    if ! grep -q $regex $FAILLOCK_CONF; then
        echo $line >> $FAILLOCK_CONF
    fi
    for pam_file in "${AUTH_FILES[@]}"
    do
        if [ -e "$pam_file" ] ; then
            PAM_FILE_PATH="$pam_file"
            if [ -f /usr/bin/authselect ]; then
                
                if ! authselect check; then
                echo "
                authselect integrity check failed. Remediation aborted!
                This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
                It is not recommended to manually edit the PAM files when authselect tool is available.
                In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
                exit 1
                fi

                CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
                # If not already in use, a custom profile is created preserving the enabled features.
                if [[ ! $CURRENT_PROFILE == custom/* ]]; then
                    ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
                    authselect create-profile hardening -b $CURRENT_PROFILE
                    CURRENT_PROFILE="custom/hardening"
                    
                    authselect apply-changes -b --backup=before-hardening-custom-profile
                    authselect select $CURRENT_PROFILE
                    for feature in $ENABLED_FEATURES; do
                        authselect enable-feature $feature;
                    done
                    
                    authselect apply-changes -b --backup=after-hardening-custom-profile
                fi
                PAM_FILE_NAME=$(basename "$pam_file")
                PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

                authselect apply-changes -b
            fi
            
        if grep -qP '^\s*auth\s.*\bpam_faillock.so\s.*\beven_deny_root\b' "$PAM_FILE_PATH"; then
            sed -i -E --follow-symlinks 's/(.*auth.*pam_faillock.so.*)\beven_deny_root\b=?[[:alnum:]]*(.*)/\1\2/g' "$PAM_FILE_PATH"
        fi
            if [ -f /usr/bin/authselect ]; then
                
                authselect apply-changes -b
            fi
        else
            echo "$pam_file was not found" >&2
        fi
    done
else
    for pam_file in "${AUTH_FILES[@]}"
    do
        if ! grep -qE '^\s*auth.*pam_faillock\.so (preauth|authfail).*even_deny_root' "$pam_file"; then
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*preauth.*silent.*/ s/$/ even_deny_root/' "$pam_file"
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*authfail.*/ s/$/ even_deny_root/' "$pam_file"
        fi
    done
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set Interval For Counting Failed Password Attempts   [ref]

Utilizing pam_faillock.so, the fail_interval directive configures the system to lock out an account after a number of incorrect login attempts within a specified time period.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report. If the system supports the /etc/security/faillock.conf file, the pam_faillock parameters should be defined in faillock.conf file.
Rationale:
By limiting the number of failed logon attempts the risk of unauthorized system access via user password guessing, otherwise known as brute-forcing, is reduced. Limits are imposed by locking the account.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_passwords_pam_faillock_interval
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, DSS05.04, DSS05.10, DSS06.10, CCI-000044, CCI-002236, CCI-002237, CCI-002238, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, CM-6(a), AC-7(a), PR.AC-7, FIA_AFL.1, SRG-OS-000329-GPOS-00128, SRG-OS-000021-GPOS-00005, SV-204427r880842_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Check if system relies
    on authselect tool
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Remediation where authselect
    tool is present
  block:

  - name: Set Interval For Counting Failed Password Attempts - Check integrity of
      authselect current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Set Interval For Counting Failed Password Attempts - Informative message
      based on the authselect integrity check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Set Interval For Counting Failed Password Attempts - Get authselect current
      features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Set Interval For Counting Failed Password Attempts - Ensure "with-faillock"
      feature is enabled using authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature with-faillock
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("with-faillock")

  - name: Set Interval For Counting Failed Password Attempts - Ensure authselect changes
      are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Remediation where authselect
    tool is not present
  block:

  - name: Set Interval For Counting Failed Password Attempts - Check if pam_faillock.so
      is already enabled
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail)
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_is_enabled

  - name: Set Interval For Counting Failed Password Attempts - Enable pam_faillock.so
      preauth editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so preauth
      insertbefore: ^auth.*sufficient.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Set Interval For Counting Failed Password Attempts - Enable pam_faillock.so
      authfail editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so authfail
      insertbefore: ^auth.*required.*pam_deny\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Set Interval For Counting Failed Password Attempts - Enable pam_faillock.so
      account section editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: account     required      pam_faillock.so
      insertbefore: ^account.*required.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_authselect_present.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_accounts_passwords_pam_faillock_fail_interval # promote to variable
  set_fact:
    var_accounts_passwords_pam_faillock_fail_interval: !!str 900
  tags:
    - always

- name: Set Interval For Counting Failed Password Attempts - Check the presence of
    /etc/security/faillock.conf file
  ansible.builtin.stat:
    path: /etc/security/faillock.conf
  register: result_faillock_conf_check
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Ensure the pam_faillock.so
    fail_interval parameter in /etc/security/faillock.conf
  ansible.builtin.lineinfile:
    path: /etc/security/faillock.conf
    regexp: ^\s*fail_interval\s*=
    line: fail_interval = {{ var_accounts_passwords_pam_faillock_fail_interval }}
    state: present
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Ensure the pam_faillock.so
    fail_interval parameter not in PAM files
  block:

  - name: Set Interval For Counting Failed Password Attempts - Check if /etc/pam.d/system-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/system-auth
    register: result_pam_file_present

  - name: Set Interval For Counting Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Set Interval For Counting Failed Password Attempts - Define the PAM file
        to be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/system-auth

    - name: Set Interval For Counting Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
        custom profile is used if authselect is present
      block:

      - name: Set Interval For Counting Failed Password Attempts - Check integrity
          of authselect current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Set Interval For Counting Failed Password Attempts - Informative message
          based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Set Interval For Counting Failed Password Attempts - Get authselect
          current profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Set Interval For Counting Failed Password Attempts - Define the current
          authselect profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Define the new
          authselect custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Get authselect
          current features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Check if any custom
          profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Interval For Counting Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Interval For Counting Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Set Interval For Counting Failed Password Attempts - Change the PAM
          file to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Set Interval For Counting Failed Password Attempts - Ensure the "fail_interval"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bfail_interval\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
        changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists

  - name: Set Interval For Counting Failed Password Attempts - Check if /etc/pam.d/password-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/password-auth
    register: result_pam_file_present

  - name: Set Interval For Counting Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Set Interval For Counting Failed Password Attempts - Define the PAM file
        to be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/password-auth

    - name: Set Interval For Counting Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
        custom profile is used if authselect is present
      block:

      - name: Set Interval For Counting Failed Password Attempts - Check integrity
          of authselect current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Set Interval For Counting Failed Password Attempts - Informative message
          based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Set Interval For Counting Failed Password Attempts - Get authselect
          current profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Set Interval For Counting Failed Password Attempts - Define the current
          authselect profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Define the new
          authselect custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Get authselect
          current features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Check if any custom
          profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Set Interval For Counting Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Interval For Counting Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Interval For Counting Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
          changes are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Set Interval For Counting Failed Password Attempts - Change the PAM
          file to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Set Interval For Counting Failed Password Attempts - Ensure the "fail_interval"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bfail_interval\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Set Interval For Counting Failed Password Attempts - Ensure authselect
        changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Interval For Counting Failed Password Attempts - Ensure the pam_faillock.so
    fail_interval parameter in PAM files
  block:

  - name: Set Interval For Counting Failed Password Attempts - Check if pam_faillock.so
      fail_interval parameter is already enabled in pam files
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail).*fail_interval
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_fail_interval_parameter_is_present

  - name: Set Interval For Counting Failed Password Attempts - Ensure the inclusion
      of pam_faillock.so preauth fail_interval parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)
      line: \1required\3 fail_interval={{ var_accounts_passwords_pam_faillock_fail_interval
        }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_fail_interval_parameter_is_present.found == 0

  - name: Set Interval For Counting Failed Password Attempts - Ensure the inclusion
      of pam_faillock.so authfail fail_interval parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)
      line: \1required\3 fail_interval={{ var_accounts_passwords_pam_faillock_fail_interval
        }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_fail_interval_parameter_is_present.found == 0

  - name: Set Interval For Counting Failed Password Attempts - Ensure the desired
      value for pam_faillock.so preauth fail_interval parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)(fail_interval)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_fail_interval }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_fail_interval_parameter_is_present.found > 0

  - name: Set Interval For Counting Failed Password Attempts - Ensure the desired
      value for pam_faillock.so authfail fail_interval parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)(fail_interval)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_fail_interval }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_fail_interval_parameter_is_present.found > 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_faillock_conf_check.stat.exists
  tags:
  - DISA-STIG-RHEL-07-010320
  - NIST-800-53-AC-7(a)
  - NIST-800-53-CM-6(a)
  - accounts_passwords_pam_faillock_interval
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_accounts_passwords_pam_faillock_fail_interval='900'


if [ -f /usr/bin/authselect ]; then
    if ! authselect check; then
echo "
authselect integrity check failed. Remediation aborted!
This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
It is not recommended to manually edit the PAM files when authselect tool is available.
In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
exit 1
fi
authselect enable-feature with-faillock

authselect apply-changes -b
else
    
AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")
for pam_file in "${AUTH_FILES[@]}"
do
    if ! grep -qE '^\s*auth\s+required\s+pam_faillock\.so\s+(preauth silent|authfail).*$' "$pam_file" ; then
        sed -i --follow-symlinks '/^auth.*sufficient.*pam_unix\.so.*/i auth        required      pam_faillock.so preauth silent' "$pam_file"
        sed -i --follow-symlinks '/^auth.*required.*pam_deny\.so.*/i auth        required      pam_faillock.so authfail' "$pam_file"
        sed -i --follow-symlinks '/^account.*required.*pam_unix\.so.*/i account     required      pam_faillock.so' "$pam_file"
    fi
    sed -Ei 's/(auth.*)(\[default=die\])(.*pam_faillock\.so)/\1required     \3/g' "$pam_file"
done

fi

AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")

FAILLOCK_CONF="/etc/security/faillock.conf"
if [ -f $FAILLOCK_CONF ]; then
    regex="^\s*fail_interval\s*="
    line="fail_interval = $var_accounts_passwords_pam_faillock_fail_interval"
    if ! grep -q $regex $FAILLOCK_CONF; then
        echo $line >> $FAILLOCK_CONF
    else
        sed -i --follow-symlinks 's|^\s*\(fail_interval\s*=\s*\)\(\S\+\)|\1'"$var_accounts_passwords_pam_faillock_fail_interval"'|g' $FAILLOCK_CONF
    fi
    for pam_file in "${AUTH_FILES[@]}"
    do
        if [ -e "$pam_file" ] ; then
            PAM_FILE_PATH="$pam_file"
            if [ -f /usr/bin/authselect ]; then
                
                if ! authselect check; then
                echo "
                authselect integrity check failed. Remediation aborted!
                This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
                It is not recommended to manually edit the PAM files when authselect tool is available.
                In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
                exit 1
                fi

                CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
                # If not already in use, a custom profile is created preserving the enabled features.
                if [[ ! $CURRENT_PROFILE == custom/* ]]; then
                    ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
                    authselect create-profile hardening -b $CURRENT_PROFILE
                    CURRENT_PROFILE="custom/hardening"
                    
                    authselect apply-changes -b --backup=before-hardening-custom-profile
                    authselect select $CURRENT_PROFILE
                    for feature in $ENABLED_FEATURES; do
                        authselect enable-feature $feature;
                    done
                    
                    authselect apply-changes -b --backup=after-hardening-custom-profile
                fi
                PAM_FILE_NAME=$(basename "$pam_file")
                PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

                authselect apply-changes -b
            fi
            
        if grep -qP '^\s*auth\s.*\bpam_faillock.so\s.*\bfail_interval\b' "$PAM_FILE_PATH"; then
            sed -i -E --follow-symlinks 's/(.*auth.*pam_faillock.so.*)\bfail_interval\b=?[[:alnum:]]*(.*)/\1\2/g' "$PAM_FILE_PATH"
        fi
            if [ -f /usr/bin/authselect ]; then
                
                authselect apply-changes -b
            fi
        else
            echo "$pam_file was not found" >&2
        fi
    done
else
    for pam_file in "${AUTH_FILES[@]}"
    do
        if ! grep -qE '^\s*auth.*pam_faillock\.so (preauth|authfail).*fail_interval' "$pam_file"; then
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*preauth.*silent.*/ s/$/ fail_interval='"$var_accounts_passwords_pam_faillock_fail_interval"'/' "$pam_file"
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*authfail.*/ s/$/ fail_interval='"$var_accounts_passwords_pam_faillock_fail_interval"'/' "$pam_file"
        else
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*preauth.*silent.*\)\('"fail_interval"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_fail_interval"'\3/' "$pam_file"
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*authfail.*\)\('"fail_interval"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_fail_interval"'\3/' "$pam_file"
        fi
    done
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set Lockout Time for Failed Password Attempts   [ref]

This rule configures the system to lock out accounts during a specified time period after a number of incorrect login attempts using pam_faillock.so. pam_faillock.so module requires multiple entries in pam files. These entries must be carefully defined to work as expected. In order to avoid any errors when manually editing these files, it is recommended to use the appropriate tools, such as authselect or authconfig, depending on the OS version. If unlock_time is set to 0, manual intervention by an administrator is required to unlock a user. This should be done using the faillock tool.
Warning:  If the system supports the new /etc/security/faillock.conf file but the pam_faillock.so parameters are defined directly in /etc/pam.d/system-auth and /etc/pam.d/password-auth, the remediation will migrate the unlock_time parameter to /etc/security/faillock.conf to ensure compatibility with authselect tool. The parameters deny and fail_interval, if used, also have to be migrated by their respective remediation.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report. If the system supports the /etc/security/faillock.conf file, the pam_faillock parameters should be defined in faillock.conf file.
Rationale:
By limiting the number of failed logon attempts the risk of unauthorized system access via user password guessing, otherwise known as brute-forcing, is reduced. Limits are imposed by locking the account.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_passwords_pam_faillock_unlock_time
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5.5.3, DSS05.04, DSS05.10, DSS06.10, 3.1.8, CCI-000044, CCI-002236, CCI-002237, CCI-002238, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, CM-6(a), AC-7(b), PR.AC-7, FIA_AFL.1, Req-8.1.7, 8.3.4, SRG-OS-000329-GPOS-00128, SRG-OS-000021-GPOS-00005, 5.3.2, SV-204427r880842_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Check if system relies on
    authselect tool
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Remediation where authselect
    tool is present
  block:

  - name: Set Lockout Time for Failed Password Attempts - Check integrity of authselect
      current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Set Lockout Time for Failed Password Attempts - Informative message based
      on the authselect integrity check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Set Lockout Time for Failed Password Attempts - Get authselect current features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Set Lockout Time for Failed Password Attempts - Ensure "with-faillock" feature
      is enabled using authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature with-faillock
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("with-faillock")

  - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
      are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - '"pam" in ansible_facts.packages'
  - result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Remediation where authselect
    tool is not present
  block:

  - name: Set Lockout Time for Failed Password Attempts - Check if pam_faillock.so
      is already enabled
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail)
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_is_enabled

  - name: Set Lockout Time for Failed Password Attempts - Enable pam_faillock.so preauth
      editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so preauth
      insertbefore: ^auth.*sufficient.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Set Lockout Time for Failed Password Attempts - Enable pam_faillock.so authfail
      editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: auth        required      pam_faillock.so authfail
      insertbefore: ^auth.*required.*pam_deny\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0

  - name: Set Lockout Time for Failed Password Attempts - Enable pam_faillock.so account
      section editing PAM files
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      line: account     required      pam_faillock.so
      insertbefore: ^account.*required.*pam_unix\.so.*
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_is_enabled.found == 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_accounts_passwords_pam_faillock_unlock_time # promote to variable
  set_fact:
    var_accounts_passwords_pam_faillock_unlock_time: !!str 0
  tags:
    - always

- name: Set Lockout Time for Failed Password Attempts - Check the presence of /etc/security/faillock.conf
    file
  ansible.builtin.stat:
    path: /etc/security/faillock.conf
  register: result_faillock_conf_check
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Ensure the pam_faillock.so
    unlock_time parameter in /etc/security/faillock.conf
  ansible.builtin.lineinfile:
    path: /etc/security/faillock.conf
    regexp: ^\s*unlock_time\s*=
    line: unlock_time = {{ var_accounts_passwords_pam_faillock_unlock_time }}
    state: present
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Ensure the pam_faillock.so
    unlock_time parameter not in PAM files
  block:

  - name: Set Lockout Time for Failed Password Attempts - Check if /etc/pam.d/system-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/system-auth
    register: result_pam_file_present

  - name: Set Lockout Time for Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Set Lockout Time for Failed Password Attempts - Define the PAM file to
        be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/system-auth

    - name: Set Lockout Time for Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Set Lockout Time for Failed Password Attempts - Ensure authselect custom
        profile is used if authselect is present
      block:

      - name: Set Lockout Time for Failed Password Attempts - Check integrity of authselect
          current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Set Lockout Time for Failed Password Attempts - Informative message
          based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Set Lockout Time for Failed Password Attempts - Get authselect current
          profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Set Lockout Time for Failed Password Attempts - Define the current authselect
          profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Define the new authselect
          custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Get authselect current
          features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Check if any custom
          profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Lockout Time for Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Lockout Time for Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Set Lockout Time for Failed Password Attempts - Change the PAM file
          to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Set Lockout Time for Failed Password Attempts - Ensure the "unlock_time"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bunlock_time\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
        are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists

  - name: Set Lockout Time for Failed Password Attempts - Check if /etc/pam.d/password-auth
      file is present
    ansible.builtin.stat:
      path: /etc/pam.d/password-auth
    register: result_pam_file_present

  - name: Set Lockout Time for Failed Password Attempts - Check the proper remediation
      for the system
    block:

    - name: Set Lockout Time for Failed Password Attempts - Define the PAM file to
        be edited as a local fact
      ansible.builtin.set_fact:
        pam_file_path: /etc/pam.d/password-auth

    - name: Set Lockout Time for Failed Password Attempts - Check if system relies
        on authselect tool
      ansible.builtin.stat:
        path: /usr/bin/authselect
      register: result_authselect_present

    - name: Set Lockout Time for Failed Password Attempts - Ensure authselect custom
        profile is used if authselect is present
      block:

      - name: Set Lockout Time for Failed Password Attempts - Check integrity of authselect
          current profile
        ansible.builtin.command:
          cmd: authselect check
        register: result_authselect_check_cmd
        changed_when: false
        failed_when: false

      - name: Set Lockout Time for Failed Password Attempts - Informative message
          based on the authselect integrity check result
        ansible.builtin.assert:
          that:
          - result_authselect_check_cmd.rc == 0
          fail_msg:
          - authselect integrity check failed. Remediation aborted!
          - This remediation could not be applied because an authselect profile was
            not selected or the selected profile is not intact.
          - It is not recommended to manually edit the PAM files when authselect tool
            is available.
          - In cases where the default authselect profile does not cover a specific
            demand, a custom authselect profile is recommended.
          success_msg:
          - authselect integrity check passed

      - name: Set Lockout Time for Failed Password Attempts - Get authselect current
          profile
        ansible.builtin.shell:
          cmd: authselect current -r | awk '{ print $1 }'
        register: result_authselect_profile
        changed_when: false
        when:
        - result_authselect_check_cmd is success

      - name: Set Lockout Time for Failed Password Attempts - Define the current authselect
          profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Define the new authselect
          custom profile as a local fact
        ansible.builtin.set_fact:
          authselect_current_profile: '{{ result_authselect_profile.stdout }}'
          authselect_custom_profile: custom/hardening
        when:
        - result_authselect_profile is not skipped
        - result_authselect_profile.stdout is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Get authselect current
          features to also enable them in the custom profile
        ansible.builtin.shell:
          cmd: authselect current | tail -n+3 | awk '{ print $2 }'
        register: result_authselect_features
        changed_when: false
        when:
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Check if any custom
          profile with the same name was already created
        ansible.builtin.stat:
          path: /etc/authselect/{{ authselect_custom_profile }}
        register: result_authselect_custom_profile_present
        changed_when: false
        when:
        - authselect_current_profile is not match("custom/")

      - name: Set Lockout Time for Failed Password Attempts - Create an authselect
          custom profile based on the current profile
        ansible.builtin.command:
          cmd: authselect create-profile hardening -b {{ authselect_current_profile
            }}
        when:
        - result_authselect_check_cmd is success
        - authselect_current_profile is not match("custom/")
        - not result_authselect_custom_profile_present.stat.exists

      - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Lockout Time for Failed Password Attempts - Ensure the authselect
          custom profile is selected
        ansible.builtin.command:
          cmd: authselect select {{ authselect_custom_profile }}
        register: result_pam_authselect_select_profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - authselect_current_profile is not match("custom/")
        - authselect_custom_profile is not match(authselect_current_profile)

      - name: Set Lockout Time for Failed Password Attempts - Restore the authselect
          features in the custom profile
        ansible.builtin.command:
          cmd: authselect enable-feature {{ item }}
        loop: '{{ result_authselect_features.stdout_lines }}'
        register: result_pam_authselect_restore_features
        when:
        - result_authselect_profile is not skipped
        - result_authselect_features is not skipped
        - result_pam_authselect_select_profile is not skipped

      - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
          are applied
        ansible.builtin.command:
          cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
        when:
        - result_authselect_check_cmd is success
        - result_authselect_profile is not skipped
        - result_pam_authselect_restore_features is not skipped

      - name: Set Lockout Time for Failed Password Attempts - Change the PAM file
          to be edited according to the custom authselect profile
        ansible.builtin.set_fact:
          pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
            | basename }}
      when:
      - result_authselect_present.stat.exists

    - name: Set Lockout Time for Failed Password Attempts - Ensure the "unlock_time"
        option from "pam_faillock.so" is not present in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: (.*auth.*pam_faillock.so.*)\bunlock_time\b=?[0-9a-zA-Z]*(.*)
        replace: \1\2
      register: result_pam_option_removal

    - name: Set Lockout Time for Failed Password Attempts - Ensure authselect changes
        are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present.stat.exists
      - result_pam_option_removal is changed
    when:
    - result_pam_file_present.stat.exists
  when:
  - '"pam" in ansible_facts.packages'
  - result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set Lockout Time for Failed Password Attempts - Ensure the pam_faillock.so
    unlock_time parameter in PAM files
  block:

  - name: Set Lockout Time for Failed Password Attempts - Check if pam_faillock.so
      unlock_time parameter is already enabled in pam files
    ansible.builtin.lineinfile:
      path: /etc/pam.d/system-auth
      regexp: .*auth.*pam_faillock\.so (preauth|authfail).*unlock_time
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_faillock_unlock_time_parameter_is_present

  - name: Set Lockout Time for Failed Password Attempts - Ensure the inclusion of
      pam_faillock.so preauth unlock_time parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)
      line: \1required\3 unlock_time={{ var_accounts_passwords_pam_faillock_unlock_time
        }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_unlock_time_parameter_is_present.found == 0

  - name: Set Lockout Time for Failed Password Attempts - Ensure the inclusion of
      pam_faillock.so authfail unlock_time parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)
      line: \1required\3 unlock_time={{ var_accounts_passwords_pam_faillock_unlock_time
        }}
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_unlock_time_parameter_is_present.found == 0

  - name: Set Lockout Time for Failed Password Attempts - Ensure the desired value
      for pam_faillock.so preauth unlock_time parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so preauth.*)(unlock_time)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_unlock_time }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_unlock_time_parameter_is_present.found > 0

  - name: Set Lockout Time for Failed Password Attempts - Ensure the desired value
      for pam_faillock.so authfail unlock_time parameter in auth section
    ansible.builtin.lineinfile:
      path: '{{ item }}'
      backrefs: true
      regexp: (^\s*auth\s+)([\w\[].*\b)(\s+pam_faillock.so authfail.*)(unlock_time)=[0-9]+(.*)
      line: \1required\3\4={{ var_accounts_passwords_pam_faillock_unlock_time }}\5
      state: present
    loop:
    - /etc/pam.d/system-auth
    - /etc/pam.d/password-auth
    when:
    - result_pam_faillock_unlock_time_parameter_is_present.found > 0
  when:
  - '"pam" in ansible_facts.packages'
  - not result_faillock_conf_check.stat.exists
  tags:
  - CJIS-5.5.3
  - DISA-STIG-RHEL-07-010320
  - NIST-800-171-3.1.8
  - NIST-800-53-AC-7(b)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.1.7
  - PCI-DSSv4-8.3.4
  - accounts_passwords_pam_faillock_unlock_time
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_accounts_passwords_pam_faillock_unlock_time='0'


if [ -f /usr/bin/authselect ]; then
    if ! authselect check; then
echo "
authselect integrity check failed. Remediation aborted!
This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
It is not recommended to manually edit the PAM files when authselect tool is available.
In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
exit 1
fi
authselect enable-feature with-faillock

authselect apply-changes -b
else
    
AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")
for pam_file in "${AUTH_FILES[@]}"
do
    if ! grep -qE '^\s*auth\s+required\s+pam_faillock\.so\s+(preauth silent|authfail).*$' "$pam_file" ; then
        sed -i --follow-symlinks '/^auth.*sufficient.*pam_unix\.so.*/i auth        required      pam_faillock.so preauth silent' "$pam_file"
        sed -i --follow-symlinks '/^auth.*required.*pam_deny\.so.*/i auth        required      pam_faillock.so authfail' "$pam_file"
        sed -i --follow-symlinks '/^account.*required.*pam_unix\.so.*/i account     required      pam_faillock.so' "$pam_file"
    fi
    sed -Ei 's/(auth.*)(\[default=die\])(.*pam_faillock\.so)/\1required     \3/g' "$pam_file"
done

fi

AUTH_FILES=("/etc/pam.d/system-auth" "/etc/pam.d/password-auth")

FAILLOCK_CONF="/etc/security/faillock.conf"
if [ -f $FAILLOCK_CONF ]; then
    regex="^\s*unlock_time\s*="
    line="unlock_time = $var_accounts_passwords_pam_faillock_unlock_time"
    if ! grep -q $regex $FAILLOCK_CONF; then
        echo $line >> $FAILLOCK_CONF
    else
        sed -i --follow-symlinks 's|^\s*\(unlock_time\s*=\s*\)\(\S\+\)|\1'"$var_accounts_passwords_pam_faillock_unlock_time"'|g' $FAILLOCK_CONF
    fi
    for pam_file in "${AUTH_FILES[@]}"
    do
        if [ -e "$pam_file" ] ; then
            PAM_FILE_PATH="$pam_file"
            if [ -f /usr/bin/authselect ]; then
                
                if ! authselect check; then
                echo "
                authselect integrity check failed. Remediation aborted!
                This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
                It is not recommended to manually edit the PAM files when authselect tool is available.
                In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
                exit 1
                fi

                CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
                # If not already in use, a custom profile is created preserving the enabled features.
                if [[ ! $CURRENT_PROFILE == custom/* ]]; then
                    ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
                    authselect create-profile hardening -b $CURRENT_PROFILE
                    CURRENT_PROFILE="custom/hardening"
                    
                    authselect apply-changes -b --backup=before-hardening-custom-profile
                    authselect select $CURRENT_PROFILE
                    for feature in $ENABLED_FEATURES; do
                        authselect enable-feature $feature;
                    done
                    
                    authselect apply-changes -b --backup=after-hardening-custom-profile
                fi
                PAM_FILE_NAME=$(basename "$pam_file")
                PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

                authselect apply-changes -b
            fi
            
        if grep -qP '^\s*auth\s.*\bpam_faillock.so\s.*\bunlock_time\b' "$PAM_FILE_PATH"; then
            sed -i -E --follow-symlinks 's/(.*auth.*pam_faillock.so.*)\bunlock_time\b=?[[:alnum:]]*(.*)/\1\2/g' "$PAM_FILE_PATH"
        fi
            if [ -f /usr/bin/authselect ]; then
                
                authselect apply-changes -b
            fi
        else
            echo "$pam_file was not found" >&2
        fi
    done
else
    for pam_file in "${AUTH_FILES[@]}"
    do
        if ! grep -qE '^\s*auth.*pam_faillock\.so (preauth|authfail).*unlock_time' "$pam_file"; then
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*preauth.*silent.*/ s/$/ unlock_time='"$var_accounts_passwords_pam_faillock_unlock_time"'/' "$pam_file"
            sed -i --follow-symlinks '/^auth.*required.*pam_faillock\.so.*authfail.*/ s/$/ unlock_time='"$var_accounts_passwords_pam_faillock_unlock_time"'/' "$pam_file"
        else
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*preauth.*silent.*\)\('"unlock_time"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_unlock_time"'\3/' "$pam_file"
            sed -i --follow-symlinks 's/\(^auth.*required.*pam_faillock\.so.*authfail.*\)\('"unlock_time"'=\)[0-9]\+\(.*\)/\1\2'"$var_accounts_passwords_pam_faillock_unlock_time"'\3/' "$pam_file"
        fi
    done
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Set Password Quality Requirements   Group contains 1 group and 8 rules
[ref]   The default pam_pwquality PAM module provides strength checking for passwords. It performs a number of checks, such as making sure passwords are not similar to dictionary words, are of at least a certain length, are not the previous password reversed, and are not simply a change of case from the previous password. It can also require passwords to be in certain character classes. The pam_pwquality module is the preferred way of configuring password requirements.

The man pages pam_pwquality(8) provide information on the capabilities and configuration of each.
Group   Set Password Quality Requirements with pam_pwquality   Group contains 8 rules
[ref]   The pam_pwquality PAM module can be configured to meet requirements for a variety of policies.

For example, to configure pam_pwquality to require at least one uppercase character, lowercase character, digit, and other (special) character, make sure that pam_pwquality exists in /etc/pam.d/system-auth:
password    requisite     pam_pwquality.so try_first_pass local_users_only retry=3 authtok_type=
If no such line exists, add one as the first line of the password section in /etc/pam.d/system-auth. Next, modify the settings in /etc/security/pwquality.conf to match the following:
difok = 4
minlen = 14
dcredit = -1
ucredit = -1
lcredit = -1
ocredit = -1
maxrepeat = 3
The arguments can be modified to ensure compliance with your organization's security policy. Discussion of each parameter follows.

Rule   Ensure PAM Enforces Password Requirements - Minimum Digit Characters   [ref]

The pam_pwquality module's dcredit parameter controls requirements for usage of digits in a password. When set to a negative number, any password will be required to contain that many digits. When set to a positive number, pam_pwquality will grant +1 additional length credit for each digit. Modify the dcredit setting in /etc/security/pwquality.conf to require the use of a digit in passwords.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.

Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possible combinations that need to be tested before the password is compromised. Requiring digits makes password guessing attacks more difficult by ensuring a larger search space.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_dcredit
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000194, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, FMT_SMF_EXT.1, Req-8.2.3, 8.3.6, 8.3.9, SRG-OS-000071-GPOS-00039, 5.4.1, SV-204409r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010140
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_dcredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_dcredit # promote to variable
  set_fact:
    var_password_pam_dcredit: !!str -1
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Digit Characters - Ensure
    PAM variable dcredit is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*dcredit
    line: dcredit = {{ var_password_pam_dcredit }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010140
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_dcredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_dcredit='-1'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^dcredit")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_dcredit"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^dcredit\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^dcredit\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Minimum Different Characters   [ref]

The pam_pwquality module's difok parameter sets the number of characters in a password that must not be present in and old password during a password change.

Modify the difok setting in /etc/security/pwquality.conf to equal 8 to require differing characters when changing passwords.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute–force attacks.

Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possible combinations that need to be tested before the password is compromised.

Requiring a minimum number of different characters during password changes ensures that newly changed passwords should not resemble previously compromised ones. Note that passwords which are changed on compromised systems will still be compromised, however.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_difok
Identifiers and References

References:  1, 12, 15, 16, 5, 5.6.2.1.1, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000195, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(b), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, SRG-OS-000072-GPOS-00040, SV-204411r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.1.1
  - DISA-STIG-RHEL-07-010160
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(b)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_difok
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_difok # promote to variable
  set_fact:
    var_password_pam_difok: !!str 8
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Different Characters -
    Ensure PAM variable difok is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*difok
    line: difok = {{ var_password_pam_difok }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.1.1
  - DISA-STIG-RHEL-07-010160
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(b)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_difok
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_difok='8'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^difok")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_difok"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^difok\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^difok\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Minimum Lowercase Characters   [ref]

The pam_pwquality module's lcredit parameter controls requirements for usage of lowercase letters in a password. When set to a negative number, any password will be required to contain that many lowercase characters. When set to a positive number, pam_pwquality will grant +1 additional length credit for each lowercase character. Modify the lcredit setting in /etc/security/pwquality.conf to require the use of a lowercase character in passwords.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.
Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possble combinations that need to be tested before the password is compromised. Requiring a minimum number of lowercase characters makes password guessing attacks more difficult by ensuring a larger search space.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_lcredit
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000193, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, FMT_SMF_EXT.1, Req-8.2.3, 8.3.6, 8.3.9, SRG-OS-000070-GPOS-00038, 5.4.1, SV-204408r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010130
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_lcredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_lcredit # promote to variable
  set_fact:
    var_password_pam_lcredit: !!str -1
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Lowercase Characters -
    Ensure PAM variable lcredit is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*lcredit
    line: lcredit = {{ var_password_pam_lcredit }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010130
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_lcredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_lcredit='-1'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^lcredit")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_lcredit"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^lcredit\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^lcredit\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Maximum Consecutive Repeating Characters from Same Character Class   [ref]

The pam_pwquality module's maxclassrepeat parameter controls requirements for consecutive repeating characters from the same character class. When set to a positive number, it will reject passwords which contain more than that number of consecutive characters from the same character class. Modify the maxclassrepeat setting in /etc/security/pwquality.conf to equal 4 to prevent a run of (4 + 1) or more identical characters.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.
Password complexity is one factor of several that determines how long it takes to crack a password. The more complex a password, the greater the number of possible combinations that need to be tested before the password is compromised.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_maxclassrepeat
Identifiers and References

References:  1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000195, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, SRG-OS-000072-GPOS-00040, SV-204414r809186_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010190
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_maxclassrepeat
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_maxclassrepeat # promote to variable
  set_fact:
    var_password_pam_maxclassrepeat: !!str 4
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Maximum Consecutive Repeating
    Characters from Same Character Class - Ensure PAM variable maxclassrepeat is set
    accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*maxclassrepeat
    line: maxclassrepeat = {{ var_password_pam_maxclassrepeat }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010190
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_maxclassrepeat
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_maxclassrepeat='4'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^maxclassrepeat")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_maxclassrepeat"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^maxclassrepeat\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^maxclassrepeat\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set Password Maximum Consecutive Repeating Characters   [ref]

The pam_pwquality module's maxrepeat parameter controls requirements for consecutive repeating characters. When set to a positive number, it will reject passwords which contain more than that number of consecutive characters. Modify the maxrepeat setting in /etc/security/pwquality.conf to equal 3 to prevent a run of (3 + 1) or more identical characters.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.

Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possible combinations that need to be tested before the password is compromised.

Passwords with excessive repeating characters may be more vulnerable to password-guessing attacks.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_maxrepeat
Identifiers and References

References:  1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000195, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, SRG-OS-000072-GPOS-00040, SV-204413r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010180
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_maxrepeat
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_maxrepeat # promote to variable
  set_fact:
    var_password_pam_maxrepeat: !!str 3
  tags:
    - always

- name: Set Password Maximum Consecutive Repeating Characters - Ensure PAM variable
    maxrepeat is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*maxrepeat
    line: maxrepeat = {{ var_password_pam_maxrepeat }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010180
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_maxrepeat
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_maxrepeat='3'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^maxrepeat")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_maxrepeat"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^maxrepeat\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^maxrepeat\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Minimum Length   [ref]

The pam_pwquality module's minlen parameter controls requirements for minimum characters required in a password. Add minlen=15 after pam_pwquality to set minimum password length requirements.
Rationale:
The shorter the password, the lower the number of possible combinations that need to be tested before the password is compromised.
Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks. Password length is one factor of several that helps to determine strength and how long it takes to crack a password. Use of more characters in a password helps to exponentially increase the time and/or resources required to compromise the password.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_minlen
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, 5.6.2.1.1, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000205, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, FMT_SMF_EXT.1, Req-8.2.3, 8.3.6, 8.3.9, SRG-OS-000078-GPOS-00046, 5.4.1, SV-204423r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.1.1
  - DISA-STIG-RHEL-07-010280
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_minlen
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_minlen # promote to variable
  set_fact:
    var_password_pam_minlen: !!str 15
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Length - Ensure PAM variable
    minlen is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*minlen
    line: minlen = {{ var_password_pam_minlen }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.1.1
  - DISA-STIG-RHEL-07-010280
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_minlen
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_minlen='15'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^minlen")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_minlen"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^minlen\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^minlen\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Minimum Special Characters   [ref]

The pam_pwquality module's ocredit= parameter controls requirements for usage of special (or "other") characters in a password. When set to a negative number, any password will be required to contain that many special characters. When set to a positive number, pam_pwquality will grant +1 additional length credit for each special character. Modify the ocredit setting in /etc/security/pwquality.conf to equal -1 to require use of a special character in passwords.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.

Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possible combinations that need to be tested before the password is compromised. Requiring a minimum number of special characters makes password guessing attacks more difficult by ensuring a larger search space.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_ocredit
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-001619, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, FMT_SMF_EXT.1, SRG-OS-000266-GPOS-00101, 5.4.1, SV-204410r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010150
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_ocredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_ocredit # promote to variable
  set_fact:
    var_password_pam_ocredit: !!str -1
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Special Characters - Ensure
    PAM variable ocredit is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*ocredit
    line: ocredit = {{ var_password_pam_ocredit }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010150
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - accounts_password_pam_ocredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_ocredit='-1'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^ocredit")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_ocredit"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^ocredit\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^ocredit\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure PAM Enforces Password Requirements - Minimum Uppercase Characters   [ref]

The pam_pwquality module's ucredit= parameter controls requirements for usage of uppercase letters in a password. When set to a negative number, any password will be required to contain that many uppercase characters. When set to a positive number, pam_pwquality will grant +1 additional length credit for each uppercase character. Modify the ucredit setting in /etc/security/pwquality.conf to require the use of an uppercase character in passwords.
Rationale:
Use of a complex password helps to increase the time and resources required to compromise the password. Password complexity, or strength, is a measure of the effectiveness of a password in resisting attempts at guessing and brute-force attacks.

Password complexity is one factor of several that determines how long it takes to crack a password. The more complex the password, the greater the number of possible combinations that need to be tested before the password is compromised.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_password_pam_ucredit
Identifiers and References

References:  BP28(R18), 1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000192, CCI-000193, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(a), CM-6(a), IA-5(4), PR.AC-1, PR.AC-6, PR.AC-7, FMT_SMF_EXT.1, Req-8.2.3, 8.3.6, 8.3.9, SRG-OS-000069-GPOS-00037, SRG-OS-000070-GPOS-00038, 5.4.1, SV-204407r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-010120
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_ucredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
- name: XCCDF Value var_password_pam_ucredit # promote to variable
  set_fact:
    var_password_pam_ucredit: !!str -1
  tags:
    - always

- name: Ensure PAM Enforces Password Requirements - Minimum Uppercase Characters -
    Ensure PAM variable ucredit is set accordingly
  ansible.builtin.lineinfile:
    create: true
    dest: /etc/security/pwquality.conf
    regexp: ^#?\s*ucredit
    line: ucredit = {{ var_password_pam_ucredit }}
  when: '"pam" in ansible_facts.packages'
  tags:
  - DISA-STIG-RHEL-07-010120
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(4)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - accounts_password_pam_ucredit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

var_password_pam_ucredit='-1'






# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^ucredit")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$var_password_pam_ucredit"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^ucredit\\>" "/etc/security/pwquality.conf"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^ucredit\\>.*/$escaped_formatted_output/gi" "/etc/security/pwquality.conf"
else
    if [[ -s "/etc/security/pwquality.conf" ]] && [[ -n "$(tail -c 1 -- "/etc/security/pwquality.conf" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/security/pwquality.conf"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/security/pwquality.conf" >> "/etc/security/pwquality.conf"
    printf '%s\n' "$formatted_output" >> "/etc/security/pwquality.conf"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Set Password Hashing Algorithm   Group contains 3 rules
[ref]   The system's default algorithm for storing password hashes in /etc/shadow is SHA-512. This can be configured in several locations.

Rule   Set Password Hashing Algorithm in /etc/libuser.conf   [ref]

In /etc/libuser.conf, add or correct the following line in its [defaults] section to ensure the system will use the SHA-512 algorithm for password hashing:
crypt_style = sha512
Rationale:
Passwords need to be protected at all times, and encryption is the standard method for protecting passwords. If passwords are not encrypted, they can be plainly read (i.e., clear text) and easily compromised. Passwords that are encrypted with a weak algorithm are no more protected than if they are kepy in plain text.

This setting ensures user and group account administration utilities are configured to store only encrypted representations of passwords. Additionally, the crypt_style configuration option ensures the use of a strong hashing algorithm that makes password cracking attacks more difficult.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_set_password_hashing_algorithm_libuserconf
Identifiers and References

References:  1, 12, 15, 16, 5, 5.6.2.2, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.13.11, CCI-000196, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0418, 1055, 1402, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(c), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.2.1, 8.3.2, SRG-OS-000073-GPOS-00041, SV-204417r877397_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010220
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - set_password_hashing_algorithm_libuserconf

- name: Set Password Hashing Algorithm in /etc/libuser.conf
  lineinfile:
    dest: /etc/libuser.conf
    insertafter: ^\s*\[defaults]
    regexp: ^#?crypt_style
    line: crypt_style = sha512
    state: present
    create: true
  when: '"libuser" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010220
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - set_password_hashing_algorithm_libuserconf

# Remediation is applicable only in certain platforms
if rpm --quiet -q libuser; then

LIBUSER_CONF="/etc/libuser.conf"
CRYPT_STYLE_REGEX='[[:space:]]*\[defaults](.*(\n)+)+?[[:space:]]*crypt_style[[:space:]]*'

# Try find crypt_style in [defaults] section. If it is here, then change algorithm to sha512.
# If it isn't here, then add it to [defaults] section.
if grep -qzosP $CRYPT_STYLE_REGEX $LIBUSER_CONF ; then
        sed -i "s/\(crypt_style[[:space:]]*=[[:space:]]*\).*/\1sha512/g" $LIBUSER_CONF
elif grep -qs "\[defaults]" $LIBUSER_CONF ; then
        sed -i "/[[:space:]]*\[defaults]/a crypt_style = sha512" $LIBUSER_CONF
else
        echo -e "[defaults]\ncrypt_style = sha512" >> $LIBUSER_CONF
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set Password Hashing Algorithm in /etc/login.defs   [ref]

In /etc/login.defs, add or correct the following line to ensure the system will use SHA512 as the hashing algorithm:
ENCRYPT_METHOD SHA512
Rationale:
Passwords need to be protected at all times, and encryption is the standard method for protecting passwords. If passwords are not encrypted, they can be plainly read (i.e., clear text) and easily compromised. Passwords that are encrypted with a weak algorithm are no more protected than if they are kept in plain text.

Using a stronger hashing algorithm makes password cracking attacks more difficult.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_set_password_hashing_algorithm_logindefs
Identifiers and References

References:  BP28(R32), 1, 12, 15, 16, 5, 5.6.2.2, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.13.11, CCI-000196, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0418, 1055, 1402, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(c), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.2.1, 8.3.2, SRG-OS-000073-GPOS-00041, 5.4.3, SV-204416r877397_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010210
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - set_password_hashing_algorithm_logindefs
- name: XCCDF Value var_password_hashing_algorithm # promote to variable
  set_fact:
    var_password_hashing_algorithm: !!str SHA512
  tags:
    - always

- name: Set Password Hashing Algorithm in /etc/login.defs
  lineinfile:
    dest: /etc/login.defs
    regexp: ^#?ENCRYPT_METHOD
    line: ENCRYPT_METHOD {{ var_password_hashing_algorithm }}
    state: present
    create: true
  when: '"shadow-utils" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010210
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - set_password_hashing_algorithm_logindefs

# Remediation is applicable only in certain platforms
if rpm --quiet -q shadow-utils; then

var_password_hashing_algorithm='SHA512'


if grep --silent ^ENCRYPT_METHOD /etc/login.defs ; then
	sed -i "s/^ENCRYPT_METHOD .*/ENCRYPT_METHOD $var_password_hashing_algorithm/g" /etc/login.defs
else
	echo "" >> /etc/login.defs
	echo "ENCRYPT_METHOD $var_password_hashing_algorithm" >> /etc/login.defs
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set PAM''s Password Hashing Algorithm   [ref]

The PAM system service can be configured to only store encrypted representations of passwords. In "/etc/pam.d/system-auth", the password section of the file controls which PAM modules execute during a password change. Set the pam_unix.so module in the password section to include the argument sha512, as shown below:
password    sufficient    pam_unix.so sha512 other arguments...

This will help ensure when local users change their passwords, hashes for the new passwords will be generated using the SHA-512 algorithm. This is the default.
Rationale:
Passwords need to be protected at all times, and encryption is the standard method for protecting passwords. If passwords are not encrypted, they can be plainly read (i.e., clear text) and easily compromised. Passwords that are encrypted with a weak algorithm are no more protected than if they are kepy in plain text.

This setting ensures user and group account administration utilities are configured to store only encrypted representations of passwords. Additionally, the crypt_style configuration option ensures the use of a strong hashing algorithm that makes password cracking attacks more difficult.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_set_password_hashing_algorithm_systemauth
Identifiers and References

References:  BP28(R32), 1, 12, 15, 16, 5, 5.6.2.2, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.13.11, CCI-000196, CCI-000803, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 0418, 1055, 1402, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-5(c), IA-5(1)(c), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.2.1, 8.3.2, SRG-OS-000073-GPOS-00041, SRG-OS-000120-GPOS-00061, 5.4.3, SV-204415r880833_rule


Complexity:low
Disruption:medium
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010200
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - set_password_hashing_algorithm_systemauth

- name: Set PAM's Password Hashing Algorithm - Check if /etc/pam.d/system-auth file
    is present
  ansible.builtin.stat:
    path: /etc/pam.d/system-auth
  register: result_pam_file_present
  when: '"pam" in ansible_facts.packages'
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010200
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - set_password_hashing_algorithm_systemauth

- name: Set PAM's Password Hashing Algorithm - Check the proper remediation for the
    system
  block:

  - name: Set PAM's Password Hashing Algorithm - Define the PAM file to be edited
      as a local fact
    ansible.builtin.set_fact:
      pam_file_path: /etc/pam.d/system-auth

  - name: Set PAM's Password Hashing Algorithm - Check if system relies on authselect
      tool
    ansible.builtin.stat:
      path: /usr/bin/authselect
    register: result_authselect_present

  - name: Set PAM's Password Hashing Algorithm - Ensure authselect custom profile
      is used if authselect is present
    block:

    - name: Set PAM's Password Hashing Algorithm - Check integrity of authselect current
        profile
      ansible.builtin.command:
        cmd: authselect check
      register: result_authselect_check_cmd
      changed_when: false
      failed_when: false

    - name: Set PAM's Password Hashing Algorithm - Informative message based on the
        authselect integrity check result
      ansible.builtin.assert:
        that:
        - result_authselect_check_cmd.rc == 0
        fail_msg:
        - authselect integrity check failed. Remediation aborted!
        - This remediation could not be applied because an authselect profile was
          not selected or the selected profile is not intact.
        - It is not recommended to manually edit the PAM files when authselect tool
          is available.
        - In cases where the default authselect profile does not cover a specific
          demand, a custom authselect profile is recommended.
        success_msg:
        - authselect integrity check passed

    - name: Set PAM's Password Hashing Algorithm - Get authselect current profile
      ansible.builtin.shell:
        cmd: authselect current -r | awk '{ print $1 }'
      register: result_authselect_profile
      changed_when: false
      when:
      - result_authselect_check_cmd is success

    - name: Set PAM's Password Hashing Algorithm - Define the current authselect profile
        as a local fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: '{{ result_authselect_profile.stdout }}'
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is match("custom/")

    - name: Set PAM's Password Hashing Algorithm - Define the new authselect custom
        profile as a local fact
      ansible.builtin.set_fact:
        authselect_current_profile: '{{ result_authselect_profile.stdout }}'
        authselect_custom_profile: custom/hardening
      when:
      - result_authselect_profile is not skipped
      - result_authselect_profile.stdout is not match("custom/")

    - name: Set PAM's Password Hashing Algorithm - Get authselect current features
        to also enable them in the custom profile
      ansible.builtin.shell:
        cmd: authselect current | tail -n+3 | awk '{ print $2 }'
      register: result_authselect_features
      changed_when: false
      when:
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")

    - name: Set PAM's Password Hashing Algorithm - Check if any custom profile with
        the same name was already created
      ansible.builtin.stat:
        path: /etc/authselect/{{ authselect_custom_profile }}
      register: result_authselect_custom_profile_present
      changed_when: false
      when:
      - authselect_current_profile is not match("custom/")

    - name: Set PAM's Password Hashing Algorithm - Create an authselect custom profile
        based on the current profile
      ansible.builtin.command:
        cmd: authselect create-profile hardening -b {{ authselect_current_profile
          }}
      when:
      - result_authselect_check_cmd is success
      - authselect_current_profile is not match("custom/")
      - not result_authselect_custom_profile_present.stat.exists

    - name: Set PAM's Password Hashing Algorithm - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=before-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Set PAM's Password Hashing Algorithm - Ensure the authselect custom profile
        is selected
      ansible.builtin.command:
        cmd: authselect select {{ authselect_custom_profile }}
      register: result_pam_authselect_select_profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - authselect_current_profile is not match("custom/")
      - authselect_custom_profile is not match(authselect_current_profile)

    - name: Set PAM's Password Hashing Algorithm - Restore the authselect features
        in the custom profile
      ansible.builtin.command:
        cmd: authselect enable-feature {{ item }}
      loop: '{{ result_authselect_features.stdout_lines }}'
      register: result_pam_authselect_restore_features
      when:
      - result_authselect_profile is not skipped
      - result_authselect_features is not skipped
      - result_pam_authselect_select_profile is not skipped

    - name: Set PAM's Password Hashing Algorithm - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b --backup=after-hardening-custom-profile
      when:
      - result_authselect_check_cmd is success
      - result_authselect_profile is not skipped
      - result_pam_authselect_restore_features is not skipped

    - name: Set PAM's Password Hashing Algorithm - Change the PAM file to be edited
        according to the custom authselect profile
      ansible.builtin.set_fact:
        pam_file_path: /etc/authselect/{{ authselect_custom_profile }}/{{ pam_file_path
          | basename }}
    when:
    - result_authselect_present.stat.exists

  - name: Set PAM's Password Hashing Algorithm - Check if expected PAM module line
      is present in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      regexp: ^\s*password\s+sufficient\s+pam_unix.so\s*.*
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_line_present

  - name: Set PAM's Password Hashing Algorithm - Include or update the PAM module
      line in {{ pam_file_path }}
    block:

    - name: Set PAM's Password Hashing Algorithm - Check if required PAM module line
        is present in {{ pam_file_path }} with different control
      ansible.builtin.lineinfile:
        path: '{{ pam_file_path }}'
        regexp: ^\s*password\s+.*\s+pam_unix.so\s*
        state: absent
      check_mode: true
      changed_when: false
      register: result_pam_line_other_control_present

    - name: Set PAM's Password Hashing Algorithm - Ensure the correct control for
        the required PAM module line in {{ pam_file_path }}
      ansible.builtin.replace:
        dest: '{{ pam_file_path }}'
        regexp: ^(\s*password\s+).*(\bpam_unix.so.*)
        replace: \1sufficient \2
      register: result_pam_module_edit
      when:
      - result_pam_line_other_control_present.found == 1

    - name: Set PAM's Password Hashing Algorithm - Ensure the required PAM module
        line is included in {{ pam_file_path }}
      ansible.builtin.lineinfile:
        dest: '{{ pam_file_path }}'
        line: password    sufficient    pam_unix.so
      register: result_pam_module_add
      when:
      - result_pam_line_other_control_present.found == 0 or result_pam_line_other_control_present.found
        > 1

    - name: Set PAM's Password Hashing Algorithm - Ensure authselect changes are applied
      ansible.builtin.command:
        cmd: authselect apply-changes -b
      when:
      - result_authselect_present is defined
      - result_authselect_present.stat.exists
      - |-
        (result_pam_module_add is defined and result_pam_module_add.changed)
         or (result_pam_module_edit is defined and result_pam_module_edit.changed)
    when:
    - result_pam_line_present.found is defined
    - result_pam_line_present.found == 0

  - name: Set PAM's Password Hashing Algorithm - Check if the required PAM module
      option is present in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      regexp: ^\s*password\s+sufficient\s+pam_unix.so\s*.*\ssha512\b
      state: absent
    check_mode: true
    changed_when: false
    register: result_pam_module_sha512_option_present

  - name: Set PAM's Password Hashing Algorithm - Ensure the "sha512" PAM option for
      "pam_unix.so" is included in {{ pam_file_path }}
    ansible.builtin.lineinfile:
      path: '{{ pam_file_path }}'
      backrefs: true
      regexp: ^(\s*password\s+sufficient\s+pam_unix.so.*)
      line: \1 sha512
      state: present
    register: result_pam_sha512_add
    when:
    - result_pam_module_sha512_option_present.found == 0

  - name: Set PAM's Password Hashing Algorithm - Ensure authselect changes are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_present.stat.exists
    - |-
      (result_pam_sha512_add is defined and result_pam_sha512_add.changed)
       or (result_pam_sha512_edit is defined and result_pam_sha512_edit.changed)
  when:
  - '"pam" in ansible_facts.packages'
  - result_pam_file_present.stat.exists
  tags:
  - CJIS-5.6.2.2
  - DISA-STIG-RHEL-07-010200
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.1
  - PCI-DSSv4-8.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - set_password_hashing_algorithm_systemauth

# Remediation is applicable only in certain platforms
if rpm --quiet -q pam; then

if [ -e "/etc/pam.d/system-auth" ] ; then
    PAM_FILE_PATH="/etc/pam.d/system-auth"
    if [ -f /usr/bin/authselect ]; then
        
        if ! authselect check; then
        echo "
        authselect integrity check failed. Remediation aborted!
        This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
        It is not recommended to manually edit the PAM files when authselect tool is available.
        In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
        exit 1
        fi

        CURRENT_PROFILE=$(authselect current -r | awk '{ print $1 }')
        # If not already in use, a custom profile is created preserving the enabled features.
        if [[ ! $CURRENT_PROFILE == custom/* ]]; then
            ENABLED_FEATURES=$(authselect current | tail -n+3 | awk '{ print $2 }')
            authselect create-profile hardening -b $CURRENT_PROFILE
            CURRENT_PROFILE="custom/hardening"
            
            authselect apply-changes -b --backup=before-hardening-custom-profile
            authselect select $CURRENT_PROFILE
            for feature in $ENABLED_FEATURES; do
                authselect enable-feature $feature;
            done
            
            authselect apply-changes -b --backup=after-hardening-custom-profile
        fi
        PAM_FILE_NAME=$(basename "/etc/pam.d/system-auth")
        PAM_FILE_PATH="/etc/authselect/$CURRENT_PROFILE/$PAM_FILE_NAME"

        authselect apply-changes -b
    fi
    if ! grep -qP '^\s*password\s+'"sufficient"'\s+pam_unix.so\s*.*' "$PAM_FILE_PATH"; then
            # Line matching group + control + module was not found. Check group + module.
            if [ "$(grep -cP '^\s*password\s+.*\s+pam_unix.so\s*' "$PAM_FILE_PATH")" -eq 1 ]; then
                # The control is updated only if one single line matches.
                sed -i -E --follow-symlinks 's/^(\s*password\s+).*(\bpam_unix.so.*)/\1'"sufficient"' \2/' "$PAM_FILE_PATH"
            else
                echo 'password    '"sufficient"'    pam_unix.so' >> "$PAM_FILE_PATH"
            fi
        fi
        # Check the option
        if ! grep -qP '^\s*password\s+'"sufficient"'\s+pam_unix.so\s*.*\ssha512\b' "$PAM_FILE_PATH"; then
            sed -i -E --follow-symlinks '/\s*password\s+'"sufficient"'\s+pam_unix.so.*/ s/$/ sha512/' "$PAM_FILE_PATH"
        fi
    if [ -f /usr/bin/authselect ]; then
        
        authselect apply-changes -b
    fi
else
    echo "/etc/pam.d/system-auth was not found" >&2
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Protect Physical Console Access   Group contains 2 groups and 8 rules
[ref]   It is impossible to fully protect a system from an attacker with physical access, so securing the space in which the system is located should be considered a necessary step. However, there are some steps which, if taken, make it more difficult for an attacker to quickly or undetectably modify a system from its console.
Group   Configure Screen Locking   Group contains 1 group and 6 rules
[ref]   When a user must temporarily leave an account logged-in, screen locking should be employed to prevent passersby from abusing the account. User education and training is particularly important for screen locking to be effective, and policies can be implemented to reinforce this.

Automatic screen locking is only meant as a safeguard for those cases where a user forgot to lock the screen.
Group   Hardware Tokens for Authentication   Group contains 6 rules

Rule   Install the opensc Package For Multifactor Authentication   [ref]

The opensc package can be installed with the following command:
$ sudo yum install opensc
Rationale:
Using an authentication device, such as a CAC or token that is separate from the information system, ensures that even if the information system is compromised, that compromise will not affect credentials stored on the authentication device.

Multifactor solutions that require devices separate from information systems gaining access include, for example, hardware tokens providing time-based or challenge-response authenticators and smart cards such as the U.S. Government Personal Identity Verification card and the DoD Common Access Card.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_package_opensc_installed
Identifiers and References

References:  CCI-001954, CCI-001953, 1382, 1384, 1386, CM-6(a), SRG-OS-000375-GPOS-00160, SRG-OS-000376-GPOS-00161


Complexity:low
Disruption:low
Strategy:enable

package --add=opensc


[[packages]]
name = "opensc"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_opensc

class install_opensc {
  package { 'opensc':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure opensc is installed
  package:
    name: opensc
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - package_opensc_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if ! rpm -q --quiet "opensc" ; then
    yum install -y "opensc"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Install the pcsc-lite package   [ref]

The pcsc-lite package can be installed with the following command:
$ sudo yum install pcsc-lite
Rationale:
The pcsc-lite package must be installed if it is to be available for multifactor authentication using smartcards.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_package_pcsc-lite_installed
Identifiers and References

References:  CCI-001954, 1382, 1384, 1386, CM-6(a), SRG-OS-000375-GPOS-00160


Complexity:low
Disruption:low
Strategy:enable

package --add=pcsc-lite


[[packages]]
name = "pcsc-lite"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_pcsc-lite

class install_pcsc-lite {
  package { 'pcsc-lite':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure pcsc-lite is installed
  package:
    name: pcsc-lite
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - package_pcsc-lite_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if ! rpm -q --quiet "pcsc-lite" ; then
    yum install -y "pcsc-lite"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable the pcscd Service   [ref]

The pcscd service can be enabled with the following command:
$ sudo systemctl enable pcscd.service
Rationale:
Using an authentication device, such as a CAC or token that is separate from the information system, ensures that even if the information system is compromised, that compromise will not affect credentials stored on the authentication device.

Multifactor solutions that require devices separate from information systems gaining access include, for example, hardware tokens providing time-based or challenge-response authenticators and smart cards such as the U.S. Government Personal Identity Verification card and the DoD Common Access Card.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_pcscd_enabled
Identifiers and References

References:  CCI-001954, 1382, 1384, 1386, IA-2(1), IA-2(2), IA-2(3), IA-2(4), IA-2(6), IA-2(7), IA-2(11), CM-6(a), Req-8.3, 8.4, SRG-OS-000375-GPOS-00160



[customizations.services]
enabled = ["pcscd"]

Complexity:low
Disruption:low
Strategy:enable
include enable_pcscd

class enable_pcscd {
  service {'pcscd':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Enable service pcscd
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Start service pcscd
    systemd:
      name: pcscd
      state: started
      masked: 'no'
    when:
    - '"pcsc-lite" in ansible_facts.packages'

  - name: Enable service pcscd
    ansible.builtin.command:
      cmd: systemctl enable pcscd
    when:
    - '"pcsc-lite" in ansible_facts.packages'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_pcscd_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'pcscd.service'
"$SYSTEMCTL_EXEC" start 'pcscd.service'
"$SYSTEMCTL_EXEC" enable 'pcscd.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Configure opensc Smart Card Drivers   [ref]

The OpenSC smart card tool can auto-detect smart card drivers; however, setting the smart card drivers in use by your organization helps to prevent users from using unauthorized smart cards. The default smart card driver for this profile is cac. To configure the OpenSC driver, edit the /etc/opensc.conf and add the following line into the file in the app default block, so it will look like:
app default {
   ...
   card_drivers = cac;
}
Rationale:
Smart card login provides two-factor authentication stronger than that provided by a username and password combination. Smart cards leverage PKI (public key infrastructure) in order to provide and verify credentials. Configuring the smart card driver in use by your organization helps to prevent users from using unauthorized smart cards.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_configure_opensc_card_drivers
Identifiers and References

References:  1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000765, CCI-000766, CCI-000767, CCI-000768, CCI-000771, CCI-000772, CCI-000884, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 1382, 1384, 1386, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-2(1), IA-2(2), IA-2(3), IA-2(4), IA-2(6), IA-2(7), IA-2(11), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.3, 8.4, SRG-OS-000104-GPOS-00051, SRG-OS-000106-GPOS-00053, SRG-OS-000107-GPOS-00054, SRG-OS-000109-GPOS-00056, SRG-OS-000108-GPOS-00055, SRG-OS-000108-GPOS-00057, SRG-OS-000108-GPOS-00058


Complexity:low
Disruption:low
Strategy:configure
- name: XCCDF Value var_smartcard_drivers # promote to variable
  set_fact:
    var_smartcard_drivers: !!str cac
  tags:
    - always

- name: Check existence of opensc conf
  stat:
    path: /etc/opensc-{{ ansible_architecture }}.conf
  register: opensc_conf_cd
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_opensc_card_drivers
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Configure smartcard driver block
  block:

  - name: Check if card_drivers is defined
    command: /usr/bin/opensc-tool -G app:default:card_drivers
    changed_when: false
    register: card_drivers

  - name: Configure opensc Smart Card Drivers
    command: |
      /usr/bin/opensc-tool -S app:default:card_drivers:{{ var_smartcard_drivers }}
    when:
    - card_drivers.stdout != var_smartcard_drivers
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - opensc_conf_cd.stat.exists
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_opensc_card_drivers
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_smartcard_drivers='cac'


OPENSC_TOOL="/usr/bin/opensc-tool"

if [ -f "${OPENSC_TOOL}" ]; then
    ${OPENSC_TOOL} -S app:default:card_drivers:$var_smartcard_drivers
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Configure NSS DB To Use opensc   [ref]

The opensc module should be configured for use over the Coolkey PKCS#11 module in the NSS database. To configure the NSS database to use the opensc module, run the following command:
$ sudo pkcs11-switch opensc
Rationale:
Smart card login provides two-factor authentication stronger than that provided by a username and password combination. Smart cards leverage PKI (public key infrastructure) in order to provide and verify credentials.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_configure_opensc_nss_db
Identifiers and References

References:  1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000765, CCI-000766, CCI-000767, CCI-000768, CCI-000771, CCI-000772, CCI-000884, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-2(1), IA-2(2), IA-2(3), IA-2(4), IA-2(6), IA-2(7), IA-2(11), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.3, SRG-OS-000104-GPOS-00051, SRG-OS-000106-GPOS-00053, SRG-OS-000107-GPOS-00054, SRG-OS-000109-GPOS-00056, SRG-OS-000108-GPOS-00055, SRG-OS-000108-GPOS-00057, SRG-OS-000108-GPOS-00058


Complexity:low
Disruption:low
Strategy:configure
- name: Check existence of pkcs11-switch
  stat:
    path: /usr/bin/pkcs11-switch
  register: pkcs11switch
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - configure_opensc_nss_db
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Get NSS database smart card configuration
  command: /usr/bin/pkcs11-switch
  changed_when: true
  register: pkcsw_output
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - pkcs11switch.stat.exists
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - configure_opensc_nss_db
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Configure NSS DB To Use opensc
  command: /usr/bin/pkcs11-switch opensc
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - pkcs11switch.stat.exists and pkcsw_output.stdout != "opensc"
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - configure_opensc_nss_db
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

PKCSSW=$(/usr/bin/pkcs11-switch)

if [ ${PKCSSW} != "opensc" ] ; then
    ${PKCSSW} opensc
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Force opensc To Use Defined Smart Card Driver   [ref]

The OpenSC smart card middleware can auto-detect smart card drivers; however by forcing the smart card driver in use by your organization, opensc will no longer autodetect or use other drivers unless specified. This helps to prevent users from using unauthorized smart cards. The default smart card driver for this profile is cac. To force the OpenSC driver, edit the /etc/opensc.conf. Look for a line similar to:
# force_card_driver = customcos;
and change it to:
force_card_driver = cac;
Rationale:
Smart card login provides two-factor authentication stronger than that provided by a username and password combination. Smart cards leverage PKI (public key infrastructure) in order to provide and verify credentials. Forcing the smart card driver in use by your organization helps to prevent users from using unauthorized smart cards.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_force_opensc_card_drivers
Identifiers and References

References:  1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, CCI-000765, CCI-000766, CCI-000767, CCI-000768, CCI-000771, CCI-000772, CCI-000884, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, 1382, 1384, 1386, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, IA-2(1), IA-2(2), IA-2(3), IA-2(4), IA-2(6), IA-2(7), IA-2(11), CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, Req-8.3, 8.4, SRG-OS-000104-GPOS-00051, SRG-OS-000106-GPOS-00053, SRG-OS-000107-GPOS-00054, SRG-OS-000109-GPOS-00056, SRG-OS-000108-GPOS-00055, SRG-OS-000108-GPOS-00057, SRG-OS-000108-GPOS-00058


Complexity:low
Disruption:low
Strategy:configure
- name: XCCDF Value var_smartcard_drivers # promote to variable
  set_fact:
    var_smartcard_drivers: !!str cac
  tags:
    - always

- name: Check existence of opensc conf
  stat:
    path: /etc/opensc-{{ ansible_architecture }}.conf
  register: opensc_conf_fcd
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - force_opensc_card_drivers
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Force smartcard driver block
  block:

  - name: Check if force_card_driver is defined
    command: /usr/bin/opensc-tool -G app:default:force_card_driver
    changed_when: false
    register: force_card_driver

  - name: Force opensc To Use Defined Smart Card Driver
    command: |
      /usr/bin/opensc-tool -S app:default:force_card_driver:{{ var_smartcard_drivers }}
    when:
    - force_card_driver.stdout != var_smartcard_drivers
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - opensc_conf_fcd.stat.exists
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2(1)
  - NIST-800-53-IA-2(11)
  - NIST-800-53-IA-2(2)
  - NIST-800-53-IA-2(3)
  - NIST-800-53-IA-2(4)
  - NIST-800-53-IA-2(6)
  - NIST-800-53-IA-2(7)
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - force_opensc_card_drivers
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_smartcard_drivers='cac'


OPENSC_TOOL="/usr/bin/opensc-tool"

if [ -f "${OPENSC_TOOL}" ]; then
    ${OPENSC_TOOL} -S app:default:force_card_driver:$var_smartcard_drivers
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Verify that Interactive Boot is Disabled   [ref]

Red Hat Enterprise Linux 7 systems support an "interactive boot" option that can be used to prevent services from being started. On a Red Hat Enterprise Linux 7 system, interactive boot can be enabled by providing a 1, yes, true, or on value to the systemd.confirm_spawn kernel argument in /etc/default/grub. Remove any instance of
systemd.confirm_spawn=(1|yes|true|on)
from the kernel arguments in that file to disable interactive boot. Recovery booting must also be disabled. Confirm that GRUB_DISABLE_RECOVERY=true is set in /etc/default/grub. It is also required to change the runtime configuration, run:
/sbin/grubby --update-kernel=ALL --remove-args="systemd.confirm_spawn"
grub2-mkconfig -o /boot/grub2/grub.cfg
Rationale:
Using interactive or recovery boot, the console user could disable auditing, firewalls, or other services, weakening system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_grub2_disable_interactive_boot
Identifiers and References

References:  11, 12, 14, 15, 16, 18, 3, 5, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.03, DSS06.06, 3.1.2, 3.4.5, CCI-000213, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, A.6.1.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, SC-2(1), CM-6(a), PR.AC-4, PR.AC-6, PR.PT-3, FIA_UAU.1, SRG-OS-000480-GPOS-00227


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.4.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-2(1)
  - grub2_disable_interactive_boot
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Verify GRUB_DISABLE_RECOVERY=true
  lineinfile:
    path: /etc/default/grub
    regexp: ^GRUB_DISABLE_RECOVERY=.*
    line: GRUB_DISABLE_RECOVERY=true
    state: present
  when: '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.4.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-2(1)
  - grub2_disable_interactive_boot
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Verify that Interactive Boot is Disabled in /etc/default/grub
  replace:
    dest: /etc/default/grub
    regexp: systemd.confirm_spawn(=(1|yes|true|on)|\b)
    replace: systemd.confirm_spawn=no
  when: '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.4.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-2(1)
  - grub2_disable_interactive_boot
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Verify that Interactive Boot is Disabled (runtime)
  command: /sbin/grubby --update-kernel=ALL --remove-args="systemd.confirm_spawn"
  when: '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.4.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-2(1)
  - grub2_disable_interactive_boot
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Regen grub.cfg handle updated GRUB_DISABLE_RECOVERY and confirm_spawn
  command: grub2-mkconfig -o  /boot/grub2/grub.cfg
  when: '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.4.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-2(1)
  - grub2_disable_interactive_boot
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
# Remediation is applicable only in certain platforms
if rpm --quiet -q grub2-common; then

# Verify that Interactive Boot is Disabled in /etc/default/grub
CONFIRM_SPAWN_YES="systemd.confirm_spawn\(=\(1\|yes\|true\|on\)\|\b\)"
CONFIRM_SPAWN_NO="systemd.confirm_spawn=no"

if grep -q "\(GRUB_CMDLINE_LINUX\|GRUB_CMDLINE_LINUX_DEFAULT\)" /etc/default/grub
then
	sed -i "s/${CONFIRM_SPAWN_YES}/${CONFIRM_SPAWN_NO}/" /etc/default/grub
fi

# make sure GRUB_DISABLE_RECOVERY=true
if grep -q '^GRUB_DISABLE_RECOVERY=.*'  '/etc/default/grub' ; then
       # modify the GRUB command-line if an GRUB_DISABLE_RECOVERY= arg already exists
       sed -i 's/GRUB_DISABLE_RECOVERY=.*/GRUB_DISABLE_RECOVERY=true/' /etc/default/grub
else
       # no GRUB_DISABLE_RECOVERY=arg is present, append it to file
       echo "GRUB_DISABLE_RECOVERY=true"  >> '/etc/default/grub'
fi



# Remove 'systemd.confirm_spawn' kernel argument also from runtime settings
/sbin/grubby --update-kernel=ALL --remove-args="systemd.confirm_spawn"


#Regen grub.cfg handle updated GRUB_DISABLE_RECOVERY and confirm_spawn
grub2-mkconfig -o /boot/grub2/grub.cfg

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Require Authentication for Single User Mode   [ref]

Single-user mode is intended as a system recovery method, providing a single user root access to the system by providing a boot option at startup.

By default, single-user mode is protected by requiring a password and is set in /usr/lib/systemd/system/rescue.service.
Rationale:
This prevents attackers with physical access from trivially bypassing security on the machine and gaining root access. Such accesses are further prevented by configuring the bootloader password.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_require_singleuser_auth
Identifiers and References

References:  1, 11, 12, 14, 15, 16, 18, 3, 5, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.06, DSS06.10, 3.1.1, 3.4.5, CCI-000213, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.18.1.4, A.6.1.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, IA-2, AC-3, CM-6(a), PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.PT-3, FIA_UAU.1, SRG-OS-000080-GPOS-00048, 1.4.3, SV-204437r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Require single user mode password
  lineinfile:
    create: true
    dest: /usr/lib/systemd/system/rescue.service
    regexp: ^#?ExecStart=
    line: ExecStart=-/bin/sh -c "/usr/sbin/sulogin; /usr/bin/systemctl --fail --no-block
      default"
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-010481
  - NIST-800-171-3.1.1
  - NIST-800-171-3.4.5
  - NIST-800-53-AC-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - require_singleuser_auth
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

service_file="/usr/lib/systemd/system/rescue.service"

sulogin='/bin/sh -c "/usr/sbin/sulogin; /usr/bin/systemctl --fail --no-block default"'

if grep "^ExecStart=.*" "$service_file" ; then
    sed -i "s%^ExecStart=.*%ExecStart=-$sulogin%" "$service_file"
else
    echo "ExecStart=-$sulogin" >> "$service_file"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Protect Accounts by Restricting Password-Based Login   Group contains 4 groups and 9 rules
[ref]   Conventionally, Unix shell accounts are accessed by providing a username and password to a login program, which tests these values for correctness using the /etc/passwd and /etc/shadow files. Password-based login is vulnerable to guessing of weak passwords, and to sniffing and man-in-the-middle attacks against passwords entered over a network or at an insecure console. Therefore, mechanisms for accessing accounts by entering usernames and passwords should be restricted to those which are operationally necessary.
Group   Set Account Expiration Parameters   Group contains 1 rule
Group   Set Password Expiration Parameters   Group contains 2 rules
[ref]   The file /etc/login.defs controls several password-related settings. Programs such as passwd, su, and login consult /etc/login.defs to determine behavior with regard to password aging, expiration warnings, and length. See the man page login.defs(5) for more information.

Users should be forced to change their passwords, in order to decrease the utility of compromised passwords. However, the need to change passwords often should be balanced against the risk that users will reuse or write down passwords if forced to change them too often. Forcing password changes every 90-360 days, depending on the environment, is recommended. Set the appropriate value as PASS_MAX_DAYS and apply it to existing accounts with the -M flag.

The PASS_MIN_DAYS (-m) setting prevents password changes for 7 days after the first change, to discourage password cycling. If you use this setting, train users to contact an administrator for an emergency password change in case a new password becomes compromised. The PASS_WARN_AGE (-W) setting gives users 7 days of warnings at login time that their passwords are about to expire.

For example, for each existing human user USER, expiration parameters could be adjusted to a 180 day maximum password age, 7 day minimum password age, and 7 day warning period with the following command:
$ sudo chage -M 180 -m 7 -W 7 USER
Group   Verify Proper Storage and Existence of Password Hashes   Group contains 1 rule
[ref]   By default, password hashes for local accounts are stored in the second field (colon-separated) in /etc/shadow. This file should be readable only by processes running with root credentials, preventing users from casually accessing others' password hashes and attempting to crack them. However, it remains possible to misconfigure the system and store password hashes in world-readable files such as /etc/passwd, or to even store passwords themselves in plaintext on the system. Using system-provided tools for password change/creation should allow administrators to avoid such misconfiguration.

Rule   Prevent Login to Accounts With Empty Password   [ref]

If an account is configured for password authentication but does not have an assigned password, it may be possible to log into the account without authentication. Remove any instances of the nullok in /etc/pam.d/system-auth and /etc/pam.d/password-auth to prevent logins with empty passwords.
Warning:  If the system relies on authselect tool to manage PAM settings, the remediation will also use authselect tool. However, if any manual modification was made in PAM files, the authselect integrity check will fail and the remediation will be aborted in order to preserve intentional changes. In this case, an informative message will be shown in the remediation report. Note that this rule is not applicable for systems running within a container. Having user with empty password within a container is not considered a risk, because it should not be possible to directly login into a container anyway.
Rationale:
If an account has an empty password, anyone could log in and run commands with the privileges of that account. Accounts with empty passwords should never be used in operational environments.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_no_empty_passwords
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 18, 3, 5, 5.5.2, APO01.06, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.02, DSS06.03, DSS06.10, 3.1.1, 3.1.5, CCI-000366, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.18.1.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, IA-5(1)(a), IA-5(c), CM-6(a), PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.DS-5, FIA_UAU.1, Req-8.2.3, 8.3.6, 8.3.9, SRG-OS-000480-GPOS-00227, SV-204424r880839_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,%23%20Generated%20by%20authselect%20on%20Sat%20Oct%2027%2014%3A59%3A36%202018%0A%23%20Do%20not%20modify%20this%20file%20manually.%0A%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_env.so%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_faildelay.so%20delay%3D2000000%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_fprintd.so%0Aauth%20%20%20%20%20%20%20%20%5Bdefault%3D1%20ignore%3Dignore%20success%3Dok%5D%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3E%3D%201000%20quiet%0Aauth%20%20%20%20%20%20%20%20%5Bdefault%3D1%20ignore%3Dignore%20success%3Dok%5D%20%20%20%20%20%20%20%20%20pam_localuser.so%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%20try_first_pass%0Aauth%20%20%20%20%20%20%20%20requisite%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3E%3D%201000%20quiet_success%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%20forward_pass%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_deny.so%0A%0Aaccount%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%0Aaccount%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_localuser.so%0Aaccount%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3C%201000%20quiet%0Aaccount%20%20%20%20%20%5Bdefault%3Dbad%20success%3Dok%20user_unknown%3Dignore%5D%20pam_sss.so%0Aaccount%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_permit.so%0A%0Apassword%20%20%20%20requisite%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_pwquality.so%20try_first_pass%20local_users_only%0Apassword%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%20sha512%20shadow%20try_first_pass%20use_authtok%0Apassword%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%20use_authtok%0Apassword%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_deny.so%0A%0Asession%20%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_keyinit.so%20revoke%0Asession%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_limits.so%0A-session%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_systemd.so%0Asession%20%20%20%20%20%5Bsuccess%3D1%20default%3Dignore%5D%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20service%20in%20crond%20quiet%20use_uid%0Asession%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%0Asession%20%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%0A
        mode: 0644
        path: /etc/pam.d/password-auth
        overwrite: true
      - contents:
          source: data:,%23%20Generated%20by%20authselect%20on%20Sat%20Oct%2027%2014%3A59%3A36%202018%0A%23%20Do%20not%20modify%20this%20file%20manually.%0A%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_env.so%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_faildelay.so%20delay%3D2000000%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_fprintd.so%0Aauth%20%20%20%20%20%20%20%20%5Bdefault%3D1%20ignore%3Dignore%20success%3Dok%5D%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3E%3D%201000%20quiet%0Aauth%20%20%20%20%20%20%20%20%5Bdefault%3D1%20ignore%3Dignore%20success%3Dok%5D%20%20%20%20%20%20%20%20%20pam_localuser.so%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%20try_first_pass%0Aauth%20%20%20%20%20%20%20%20requisite%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3E%3D%201000%20quiet_success%0Aauth%20%20%20%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%20forward_pass%0Aauth%20%20%20%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_deny.so%0A%0Aaccount%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%0Aaccount%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_localuser.so%0Aaccount%20%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20uid%20%3C%201000%20quiet%0Aaccount%20%20%20%20%20%5Bdefault%3Dbad%20success%3Dok%20user_unknown%3Dignore%5D%20pam_sss.so%0Aaccount%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_permit.so%0A%0Apassword%20%20%20%20requisite%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_pwquality.so%20try_first_pass%20local_users_only%0Apassword%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%20sha512%20shadow%20try_first_pass%20use_authtok%0Apassword%20%20%20%20sufficient%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%20use_authtok%0Apassword%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_deny.so%0A%0Asession%20%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_keyinit.so%20revoke%0Asession%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_limits.so%0A-session%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_systemd.so%0Asession%20%20%20%20%20%5Bsuccess%3D1%20default%3Dignore%5D%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_succeed_if.so%20service%20in%20crond%20quiet%20use_uid%0Asession%20%20%20%20%20required%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_unix.so%0Asession%20%20%20%20%20optional%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20pam_sss.so%0A
        mode: 0644
        path: /etc/pam.d/system-auth
        overwrite: true

Complexity:low
Disruption:medium
Strategy:configure
- name: Prevent Login to Accounts With Empty Password - Check if system relies on
    authselect
  ansible.builtin.stat:
    path: /usr/bin/authselect
  register: result_authselect_present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.2
  - DISA-STIG-RHEL-07-010290
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - configure_strategy
  - high_severity
  - low_complexity
  - medium_disruption
  - no_empty_passwords
  - no_reboot_needed

- name: Prevent Login to Accounts With Empty Password - Remediate using authselect
  block:

  - name: Prevent Login to Accounts With Empty Password - Check integrity of authselect
      current profile
    ansible.builtin.command:
      cmd: authselect check
    register: result_authselect_check_cmd
    changed_when: false
    failed_when: false

  - name: Prevent Login to Accounts With Empty Password - Informative message based
      on the authselect integrity check result
    ansible.builtin.assert:
      that:
      - result_authselect_check_cmd.rc == 0
      fail_msg:
      - authselect integrity check failed. Remediation aborted!
      - This remediation could not be applied because an authselect profile was not
        selected or the selected profile is not intact.
      - It is not recommended to manually edit the PAM files when authselect tool
        is available.
      - In cases where the default authselect profile does not cover a specific demand,
        a custom authselect profile is recommended.
      success_msg:
      - authselect integrity check passed

  - name: Prevent Login to Accounts With Empty Password - Get authselect current features
    ansible.builtin.shell:
      cmd: authselect current | tail -n+3 | awk '{ print $2 }'
    register: result_authselect_features
    changed_when: false
    when:
    - result_authselect_check_cmd is success

  - name: Prevent Login to Accounts With Empty Password - Ensure "without-nullok"
      feature is enabled using authselect tool
    ansible.builtin.command:
      cmd: authselect enable-feature without-nullok
    register: result_authselect_enable_feature_cmd
    when:
    - result_authselect_check_cmd is success
    - result_authselect_features.stdout is not search("without-nullok")

  - name: Prevent Login to Accounts With Empty Password - Ensure authselect changes
      are applied
    ansible.builtin.command:
      cmd: authselect apply-changes -b
    when:
    - result_authselect_enable_feature_cmd is not skipped
    - result_authselect_enable_feature_cmd is success
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.2
  - DISA-STIG-RHEL-07-010290
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - configure_strategy
  - high_severity
  - low_complexity
  - medium_disruption
  - no_empty_passwords
  - no_reboot_needed

- name: Prevent Login to Accounts With Empty Password - Remediate directly editing
    PAM files
  ansible.builtin.replace:
    dest: '{{ item }}'
    regexp: nullok
  loop:
  - /etc/pam.d/system-auth
  - /etc/pam.d/password-auth
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - not result_authselect_present.stat.exists
  tags:
  - CJIS-5.5.2
  - DISA-STIG-RHEL-07-010290
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(a)
  - NIST-800-53-IA-5(c)
  - PCI-DSS-Req-8.2.3
  - PCI-DSSv4-8.3.6
  - PCI-DSSv4-8.3.9
  - configure_strategy
  - high_severity
  - low_complexity
  - medium_disruption
  - no_empty_passwords
  - no_reboot_needed

Complexity:low
Disruption:medium
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -f /usr/bin/authselect ]; then
    if ! authselect check; then
echo "
authselect integrity check failed. Remediation aborted!
This remediation could not be applied because an authselect profile was not selected or the selected profile is not intact.
It is not recommended to manually edit the PAM files when authselect tool is available.
In cases where the default authselect profile does not cover a specific demand, a custom authselect profile is recommended."
exit 1
fi
authselect enable-feature without-nullok

authselect apply-changes -b
else
    
if grep -qP '^\s*auth\s+'"sufficient"'\s+pam_unix.so\s.*\bnullok\b' "/etc/pam.d/system-auth"; then
    sed -i -E --follow-symlinks 's/(.*auth.*'"sufficient"'.*pam_unix.so.*)\snullok=?[[:alnum:]]*(.*)/\1\2/g' "/etc/pam.d/system-auth"
fi
    
if grep -qP '^\s*password\s+'"sufficient"'\s+pam_unix.so\s.*\bnullok\b' "/etc/pam.d/system-auth"; then
    sed -i -E --follow-symlinks 's/(.*password.*'"sufficient"'.*pam_unix.so.*)\snullok=?[[:alnum:]]*(.*)/\1\2/g' "/etc/pam.d/system-auth"
fi
    
if grep -qP '^\s*auth\s+'"sufficient"'\s+pam_unix.so\s.*\bnullok\b' "/etc/pam.d/password-auth"; then
    sed -i -E --follow-symlinks 's/(.*auth.*'"sufficient"'.*pam_unix.so.*)\snullok=?[[:alnum:]]*(.*)/\1\2/g' "/etc/pam.d/password-auth"
fi
    
if grep -qP '^\s*password\s+'"sufficient"'\s+pam_unix.so\s.*\bnullok\b' "/etc/pam.d/password-auth"; then
    sed -i -E --follow-symlinks 's/(.*password.*'"sufficient"'.*pam_unix.so.*)\snullok=?[[:alnum:]]*(.*)/\1\2/g' "/etc/pam.d/password-auth"
fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Restrict Root Logins   Group contains 5 rules
[ref]   Direct root logins should be allowed only for emergency use. In normal situations, the administrator should access the system via a unique unprivileged account, and then use su or sudo to execute privileged commands. Discouraging administrators from accessing the root account directly ensures an audit trail in organizations with multiple administrators. Locking down the channels through which root can connect directly also reduces opportunities for password-guessing against the root account. The login program uses the file /etc/securetty to determine which interfaces should allow root logins. The virtual devices /dev/console and /dev/tty* represent the system consoles (accessible via the Ctrl-Alt-F1 through Ctrl-Alt-F6 keyboard sequences on a default installation). The default securetty file also contains /dev/vc/*. These are likely to be deprecated in most environments, but may be retained for compatibility. Root should also be prohibited from connecting via network protocols. Other sections of this document include guidance describing how to prevent root from logging in via SSH.

Rule   Verify Only Root Has UID 0   [ref]

If any account other than root has a UID of 0, this misconfiguration should be investigated and the accounts other than root should be removed or have their UID changed.
If the account is associated with system commands or applications the UID should be changed to one greater than "0" but less than "1000." Otherwise assign a UID greater than "1000" that has not already been assigned.
Rationale:
An account has root authority if it has a UID of 0. Multiple accounts with a UID of 0 afford more opportunity for potential intruders to guess a password for a privileged account. Proper configuration of sudo is recommended to afford multiple system administrators access to root privileges in an accountable manner.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_accounts_no_uid_except_zero
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.02, DSS06.03, DSS06.10, 3.1.1, 3.1.5, CCI-000366, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.18.1.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, IA-2, AC-6(5), IA-4(b), PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.DS-5, Req-8.5, 8.2.2, 8.2.3, SRG-OS-000480-GPOS-00227, 6.2.9, SV-204462r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Get all /etc/passwd file entries
  getent:
    database: passwd
    split: ':'
  tags:
  - DISA-STIG-RHEL-07-020310
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-AC-6(5)
  - NIST-800-53-IA-2
  - NIST-800-53-IA-4(b)
  - PCI-DSS-Req-8.5
  - PCI-DSSv4-8.2.2
  - PCI-DSSv4-8.2.3
  - accounts_no_uid_except_zero
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy

- name: Lock the password of the user accounts other than root with uid 0
  command: passwd -l {{ item.key }}
  loop: '{{ getent_passwd | dict2items | rejectattr(''key'', ''search'', ''root'')
    | list }}'
  when: item.value.1  == '0'
  tags:
  - DISA-STIG-RHEL-07-020310
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-AC-6(5)
  - NIST-800-53-IA-2
  - NIST-800-53-IA-4(b)
  - PCI-DSS-Req-8.5
  - PCI-DSSv4-8.2.2
  - PCI-DSSv4-8.2.3
  - accounts_no_uid_except_zero
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy

awk -F: '$3 == 0 && $1 != "root" { print $1 }' /etc/passwd | xargs --no-run-if-empty --max-lines=1 passwd -l

Rule   Direct root Logins Not Allowed   [ref]

To further limit access to the root account, administrators can disable root logins at the console by editing the /etc/securetty file. This file lists all devices the root user is allowed to login to. If the file does not exist at all, the root user can login through any communication device on the system, whether via the console or via a raw network interface. This is dangerous as user can login to the system as root via Telnet, which sends the password in plain text over the network. By default, Red Hat Enterprise Linux 7's /etc/securetty file only allows the root user to login at the console physically attached to the system. To prevent root from logging in, remove the contents of this file. To prevent direct root logins, remove the contents of this file by typing the following command:
$ sudo echo > /etc/securetty
Warning:  This rule only checks the /etc/securetty file existence and its content. If you need to restrict user access using the /etc/securetty file, make sure the pam_securetty.so PAM module is properly enabled in relevant PAM files.
Rationale:
Disabling direct root logins ensures proper accountability and multifactor authentication to privileged accounts. Users will first login, then escalate to privileged (root) access via su / sudo. This is required for FISMA Low and FISMA Moderate systems.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_no_direct_root_logins
Identifiers and References

References:  BP28(R19), 1, 12, 15, 16, 5, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.1, 3.1.6, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, A.18.1.4, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, IA-2, CM-6(a), PR.AC-1, PR.AC-6, PR.AC-7, 8.6.1, 5.5


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,
        mode: 0600
        path: /etc/securetty
        overwrite: true

Complexity:low
Disruption:low
Strategy:restrict
- name: Direct root Logins Not Allowed
  copy:
    dest: /etc/securetty
    content: ''
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.6
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-2
  - PCI-DSSv4-8.6.1
  - low_complexity
  - low_disruption
  - medium_severity
  - no_direct_root_logins
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

echo > /etc/securetty

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure that System Accounts Are Locked   [ref]

Some accounts are not associated with a human user of the system, and exist to perform some administrative functions. An attacker should not be able to log into these accounts.

System accounts are those user accounts with a user ID less than 1000. If any system account other than root, halt, sync, shutdown and nfsnobody has an unlocked password, disable it with the command:
$ sudo usermod -L account
Rationale:
Disabling authentication for default system accounts makes it more difficult for attackers to make use of them to compromise a system.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_no_password_auth_for_systemaccounts
Identifiers and References

References:  CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, AC-6, CM-6(a)


Complexity:low
Disruption:medium
Strategy:restrict
- name: Ensure that System Accounts Are Locked - Get All Local Users From /etc/passwd
  ansible.builtin.getent:
    database: passwd
    split: ':'
  tags:
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_password_auth_for_systemaccounts
  - no_reboot_needed
  - restrict_strategy

- name: Ensure that System Accounts Are Locked - Create local_users Variable From
    getent_passwd Facts
  ansible.builtin.set_fact:
    local_users: '{{ ansible_facts.getent_passwd | dict2items }}'
  tags:
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_password_auth_for_systemaccounts
  - no_reboot_needed
  - restrict_strategy

- name: Ensure that System Accounts Are Locked - Lock System Accounts
  ansible.builtin.user:
    name: '{{ item.key }}'
    password_lock: true
  loop: '{{ local_users }}'
  when:
  - item.value[1]|int < 1000
  - item.key not in ['root', 'halt', 'sync', 'shutdown', 'nfsnobody']
  tags:
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_password_auth_for_systemaccounts
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:medium
Strategy:restrict

readarray -t systemaccounts < <(awk -F: \
  '($3 < 1000 && $3 != root && $3 != halt && $3 != sync && $3 != shutdown \
  && $3 != nfsnobody) { print $1 }' /etc/passwd)

for systemaccount in "${systemaccounts[@]}"; do
    usermod -L "$systemaccount"
done

Rule   Restrict Serial Port Root Logins   [ref]

To restrict root logins on serial ports, ensure lines of this form do not appear in /etc/securetty:
ttyS0
ttyS1
Rationale:
Preventing direct root login to serial port interfaces helps ensure accountability for actions taken on the systems using the root account.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_restrict_serial_port_logins
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.1.1, 3.1.5, CCI-000770, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, AC-6, CM-6(a), PR.AC-4, PR.DS-5


Complexity:low
Disruption:low
Strategy:restrict
- name: Restrict Serial Port Root Logins
  lineinfile:
    dest: /etc/securetty
    regexp: ttyS[0-9]
    state: absent
  tags:
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_serial_port_logins
  - restrict_strategy

sed -i '/ttyS/d' /etc/securetty
Group   System Accounting with auditd   Group contains 8 groups and 63 rules
[ref]   The audit service provides substantial capabilities for recording system activities. By default, the service audits about SELinux AVC denials and certain types of security-relevant events such as system logins, account modifications, and authentication events performed by programs such as sudo. Under its default configuration, auditd has modest disk space requirements, and should not noticeably impact system performance.

NOTE: The Linux Audit daemon auditd can be configured to use the augenrules program to read audit rules files (*.rules) located in /etc/audit/rules.d location and compile them to create the resulting form of the /etc/audit/audit.rules configuration file during the daemon startup (default configuration). Alternatively, the auditd daemon can use the auditctl utility to read audit rules from the /etc/audit/audit.rules configuration file during daemon startup, and load them into the kernel. The expected behavior is configured via the appropriate ExecStartPost directive setting in the /usr/lib/systemd/system/auditd.service configuration file. To instruct the auditd daemon to use the augenrules program to read audit rules (default configuration), use the following setting:
ExecStartPost=-/sbin/augenrules --load
in the /usr/lib/systemd/system/auditd.service configuration file. In order to instruct the auditd daemon to use the auditctl utility to read audit rules, use the following setting:
ExecStartPost=-/sbin/auditctl -R /etc/audit/audit.rules
in the /usr/lib/systemd/system/auditd.service configuration file. Refer to [Service] section of the /usr/lib/systemd/system/auditd.service configuration file for further details.

Government networks often have substantial auditing requirements and auditd can be configured to meet these requirements. Examining some example audit records demonstrates how the Linux audit system satisfies common requirements. The following example from Red Hat Enterprise Linux 7 Documentation available at https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/7/html-single/selinux_users_and_administrators_guide/index#sect-Security-Enhanced_Linux-Fixing_Problems-Raw_Audit_Messages shows the substantial amount of information captured in a two typical "raw" audit messages, followed by a breakdown of the most important fields. In this example the message is SELinux-related and reports an AVC denial (and the associated system call) that occurred when the Apache HTTP Server attempted to access the /var/www/html/file1 file (labeled with the samba_share_t type):
type=AVC msg=audit(1226874073.147:96): avc:  denied  { getattr } for pid=2465 comm="httpd"
path="/var/www/html/file1" dev=dm-0 ino=284133 scontext=unconfined_u:system_r:httpd_t:s0
tcontext=unconfined_u:object_r:samba_share_t:s0 tclass=file

type=SYSCALL msg=audit(1226874073.147:96): arch=40000003 syscall=196 success=no exit=-13
a0=b98df198 a1=bfec85dc a2=54dff4 a3=2008171 items=0 ppid=2463 pid=2465 auid=502 uid=48
gid=48 euid=48 suid=48 fsuid=48 egid=48 sgid=48 fsgid=48 tty=(none) ses=6 comm="httpd"
exe="/usr/sbin/httpd" subj=unconfined_u:system_r:httpd_t:s0 key=(null)
  • msg=audit(1226874073.147:96)
    • The number in parentheses is the unformatted time stamp (Epoch time) for the event, which can be converted to standard time by using the date command.
  • { getattr }
    • The item in braces indicates the permission that was denied. getattr indicates the source process was trying to read the target file's status information. This occurs before reading files. This action is denied due to the file being accessed having the wrong label. Commonly seen permissions include getattr, read, and write.
  • comm="httpd"
    • The executable that launched the process. The full path of the executable is found in the exe= section of the system call (SYSCALL) message, which in this case, is exe="/usr/sbin/httpd".
  • path="/var/www/html/file1"
    • The path to the object (target) the process attempted to access.
  • scontext="unconfined_u:system_r:httpd_t:s0"
    • The SELinux context of the process that attempted the denied action. In this case, it is the SELinux context of the Apache HTTP Server, which is running in the httpd_t domain.
  • tcontext="unconfined_u:object_r:samba_share_t:s0"
    • The SELinux context of the object (target) the process attempted to access. In this case, it is the SELinux context of file1. Note: the samba_share_t type is not accessible to processes running in the httpd_t domain.
  • From the system call (SYSCALL) message, two items are of interest:
    • success=no: indicates whether the denial (AVC) was enforced or not. success=no indicates the system call was not successful (SELinux denied access). success=yes indicates the system call was successful - this can be seen for permissive domains or unconfined domains, such as initrc_t and kernel_t.
    • exe="/usr/sbin/httpd": the full path to the executable that launched the process, which in this case, is exe="/usr/sbin/httpd".
Group   Configure auditd Rules for Comprehensive Auditing   Group contains 7 groups and 61 rules
[ref]   The auditd program can perform comprehensive monitoring of system activity. This section describes recommended configuration settings for comprehensive auditing, but a full description of the auditing system's capabilities is beyond the scope of this guide. The mailing list linux-audit@redhat.com exists to facilitate community discussion of the auditing system.

The audit subsystem supports extensive collection of events, including:
  • Tracing of arbitrary system calls (identified by name or number) on entry or exit.
  • Filtering by PID, UID, call success, system call argument (with some limitations), etc.
  • Monitoring of specific files for modifications to the file's contents or metadata.

Auditing rules at startup are controlled by the file /etc/audit/audit.rules. Add rules to it to meet the auditing requirements for your organization. Each line in /etc/audit/audit.rules represents a series of arguments that can be passed to auditctl and can be individually tested during runtime. See documentation in /usr/share/doc/audit-VERSION and in the related man pages for more details.

If copying any example audit rulesets from /usr/share/doc/audit-VERSION, be sure to comment out the lines containing arch= which are not appropriate for your system's architecture. Then review and understand the following rules, ensuring rules are activated as needed for the appropriate architecture.

After reviewing all the rules, reading the following sections, and editing as needed, the new rules can be activated as follows:
$ sudo service auditd restart
Group   Record Events that Modify the System's Discretionary Access Controls   Group contains 13 rules
[ref]   At a minimum, the audit system should collect file permission changes for all users and root. Note that the "-F arch=b32" lines should be present even on a 64 bit system. These commands identify system calls for auditing. Even if the system is 64 bit it can still execute 32 bit system calls. Additionally, these rules can be configured in a number of ways while still achieving the desired effect. An example of this is that the "-S" calls could be split up and placed on separate lines, however, this is less efficient. Add the following to /etc/audit/audit.rules:
-a always,exit -F arch=b32 -S chmod,fchmod,fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
    -a always,exit -F arch=b32 -S chown,fchown,fchownat,lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
    -a always,exit -F arch=b32 -S setxattr,lsetxattr,fsetxattr,removexattr,lremovexattr,fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If your system is 64 bit then these lines should be duplicated and the arch=b32 replaced with arch=b64 as follows:
-a always,exit -F arch=b64 -S chmod,fchmod,fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
    -a always,exit -F arch=b64 -S chown,fchown,fchownat,lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
    -a always,exit -F arch=b64 -S setxattr,lsetxattr,fsetxattr,removexattr,lremovexattr,fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod

Rule   Record Events that Modify the System's Discretionary Access Controls - chmod   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S chmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S chmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S chmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S chmod -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_chmod
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, 4.1.9, SV-204521r809772_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit chmod tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for chmod for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of chmod in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of chmod in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for chmod for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of chmod in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of chmod in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="chmod"
	KEY="perm_mod"
	SYSCALL_GROUPING="chmod fchmod fchmodat"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - chown   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S chown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S chown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S chown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S chown -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_chown
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, SRG-OS-000474-GPOS-00219, 4.1.9, SV-204517r809570_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit chown tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for chown for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of chown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of chown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for chown for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of chown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - chown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of chown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_chown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="chown"
	KEY="perm_mod"
	SYSCALL_GROUPING="chown fchown fchownat lchown"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fchmod   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fchmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fchmod -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchmod -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fchmod
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, 4.1.9, SV-204521r809772_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fchmod tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchmod for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmod in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmod in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchmod for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmod in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmod
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmod in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmod
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fchmod"
	KEY="perm_mod"
	SYSCALL_GROUPING="chmod fchmod fchmodat"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fchmodat   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchmodat -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fchmodat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, 4.1.9, SV-204521r809772_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmodat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fchmodat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmodat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchmodat for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmodat
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmodat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmodat
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmodat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmodat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchmodat for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmodat
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmodat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchmodat
      syscall_grouping:
      - chmod
      - fchmod
      - fchmodat

  - name: Check existence of fchmodat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030410
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchmodat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fchmodat"
	KEY="perm_mod"
	SYSCALL_GROUPING="chmod fchmod fchmodat"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fchown   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchown -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fchown
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, SRG-OS-000474-GPOS-00219, 4.1.9, SV-204517r809570_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fchown tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchown for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchown for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fchown"
	KEY="perm_mod"
	SYSCALL_GROUPING="chown fchown fchownat lchown"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fchownat   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fchownat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchownat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fchownat -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fchownat -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fchownat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, SRG-OS-000474-GPOS-00219, 4.1.9, SV-204517r809570_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchownat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fchownat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchownat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchownat for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchownat
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchownat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchownat
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchownat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchownat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fchownat for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchownat
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchownat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fchownat
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of fchownat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fchownat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fchownat"
	KEY="perm_mod"
	SYSCALL_GROUPING="chown fchown fchownat lchown"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fremovexattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root.

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fremovexattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000458-GPOS-00203, SRG-OS-000462-GPOS-00206, SRG-OS-000463-GPOS-00207, SRG-OS-000471-GPOS-00215, SRG-OS-000474-GPOS-00219, SRG-OS-000466-GPOS-00210, SRG-OS-000468-GPOS-00212, SRG-OS-000064-GPOS-00033, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fremovexattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fremovexattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fremovexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fremovexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fremovexattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fremovexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fremovexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fremovexattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - fsetxattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S fsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S fsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S fsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_fsetxattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000458-GPOS-00203, SRG-OS-000462-GPOS-00206, SRG-OS-000463-GPOS-00207, SRG-OS-000466-GPOS-00210, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SRG-OS-000474-GPOS-00219, SRG-OS-000064-GPOS-00033, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit fsetxattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fsetxattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fsetxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fsetxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for fsetxattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fsetxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - fsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of fsetxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_fsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="fsetxattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - lchown   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lchown -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_lchown
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000466-GPOS-00210, SRG-OS-000458-GPOS-00203, SRG-OS-000474-GPOS-00219, 4.1.9, SV-204517r809570_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit lchown tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lchown for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of lchown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of lchown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lchown for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of lchown in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lchown
      syscall_grouping:
      - chown
      - fchown
      - fchownat
      - lchown

  - name: Check existence of lchown in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030370
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lchown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="lchown"
	KEY="perm_mod"
	SYSCALL_GROUPING="chown fchown fchownat lchown"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - lremovexattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root.

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S lremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S lremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lremovexattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_lremovexattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000458-GPOS-00203, SRG-OS-000462-GPOS-00206, SRG-OS-000463-GPOS-00207, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SRG-OS-000474-GPOS-00219, SRG-OS-000466-GPOS-00210, SRG-OS-000064-GPOS-00033, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit lremovexattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lremovexattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lremovexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lremovexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lremovexattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lremovexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lremovexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lremovexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lremovexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="lremovexattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - lsetxattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S lsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S lsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S lsetxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_lsetxattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000458-GPOS-00203, SRG-OS-000462-GPOS-00206, SRG-OS-000463-GPOS-00207, SRG-OS-000466-GPOS-00210, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SRG-OS-000474-GPOS-00219, SRG-OS-000064-GPOS-00033, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit lsetxattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lsetxattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lsetxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lsetxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for lsetxattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lsetxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - lsetxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of lsetxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_lsetxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="lsetxattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - removexattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root.

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S removexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S removexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S removexattr -F auid>=1000 -F auid!=unset -F key=perm_mod


If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S removexattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_removexattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000458-GPOS-00203, SRG-OS-000462-GPOS-00206, SRG-OS-000463-GPOS-00207, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SRG-OS-000474-GPOS-00219, SRG-OS-000466-GPOS-00210, SRG-OS-000064-GPOS-00033, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_removexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit removexattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_removexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for removexattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - removexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of removexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - removexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of removexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_removexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for removexattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - removexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of removexattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - removexattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of removexattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_removexattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="removexattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify the System's Discretionary Access Controls - setxattr   [ref]

At a minimum, the audit system should collect file permission changes for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S setxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S setxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S setxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
If the system is 64 bit then also add the following line:
-a always,exit -F arch=b64 -S setxattr -F auid>=1000 -F auid!=unset -F key=perm_mod
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
The changing of file permissions could indicate that a user is attempting to gain access to information that would otherwise be disallowed. Auditing DAC modifications can facilitate the identification of patterns of abuse among both authorized and unauthorized users.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_dac_modification_setxattr
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.5.5, 10.3.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000466-GPOS-00210, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, 4.1.9, SV-204524r809775_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_setxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit setxattr tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_setxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for setxattr for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - setxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of setxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - setxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of setxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_setxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for setxattr for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - setxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of setxattr in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - setxattr
      syscall_grouping:
      - fremovexattr
      - lremovexattr
      - removexattr
      - fsetxattr
      - lsetxattr
      - setxattr

  - name: Check existence of setxattr in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030440
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.5
  - PCI-DSSv4-10.3.4
  - audit_rules_dac_modification_setxattr
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="setxattr"
	KEY="perm_mod"
	SYSCALL_GROUPING="fremovexattr lremovexattr removexattr fsetxattr lsetxattr setxattr"

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Record Execution Attempts to Run SELinux Privileged Commands   Group contains 4 rules
[ref]   At a minimum, the audit system should collect the execution of SELinux privileged commands for all users and root.

Rule   Record Any Attempts to Run chcon   [ref]

At a minimum, the audit system should collect any execution attempt of the chcon command for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/chcon -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F path=/usr/bin/chcon -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_execution_chcon
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SRG-OS-000463-GPOS-00207, SRG-OS-000465-GPOS-00209, SV-204538r861020_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030580
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_chcon
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/chcon
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chcon -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/chcon -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chcon -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chcon -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/chcon -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chcon -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030580
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_chcon
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/chcon -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Any Attempts to Run semanage   [ref]

At a minimum, the audit system should collect any execution attempt of the semanage command for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/semanage -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F path=/usr/sbin/semanage -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_execution_semanage
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000463-GPOS-00207, SRG-OS-000465-GPOS-00209, SV-204536r861014_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030560
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_semanage
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/semanage
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/semanage -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/semanage -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/semanage -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/semanage -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/semanage -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/semanage -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030560
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_semanage
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/semanage -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Any Attempts to Run setfiles   [ref]

At a minimum, the audit system should collect any execution attempt of the setfiles command for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/setfiles -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F path=/usr/sbin/setfiles -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_execution_setfiles
Identifiers and References

References:  CCI-000169, CCI-000172, CCI-002884, AU-2(d), AU-12(c), AC-6(9), CM-6(a), SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000463-GPOS-00207, SRG-OS-000465-GPOS-00209, SV-204539r861023_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030590
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_setfiles
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/setfiles
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/setfiles -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/setfiles -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/setfiles -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/setfiles -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/setfiles -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/setfiles -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030590
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_setfiles
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/setfiles -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Any Attempts to Run setsebool   [ref]

At a minimum, the audit system should collect any execution attempt of the setsebool command for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/setsebool -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F path=/usr/sbin/setsebool -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_execution_setsebool
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000463-GPOS-00207, SRG-OS-000465-GPOS-00209, SV-204537r861017_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030570
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_setsebool
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/setsebool
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/setsebool -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/setsebool -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/setsebool -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/setsebool -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/setsebool -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/setsebool -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030570
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_execution_setsebool
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/setsebool -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Record File Deletion Events by User   Group contains 5 rules
[ref]   At a minimum, the audit system should collect file deletion events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rmdir,unlink,unlinkat,rename,renameat -F auid>=1000 -F auid!=unset -F key=delete
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rmdir,unlink,unlinkat,rename,renameat -F auid>=1000 -F auid!=unset -F key=delete

Rule   Ensure auditd Collects File Deletion Events by User - rename   [ref]

At a minimum, the audit system should collect file deletion events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rename -F auid>=1000 -F auid!=unset -F key=delete
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rename -F auid>=1000 -F auid!=unset -F key=delete
Rationale:
Auditing file deletions will create an audit trail for files that are removed from the system. The audit trail could aid in system troubleshooting, as well as, detecting malicious processes that attempt to delete log files to conceal their presence.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_file_deletion_events_rename
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-000366, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.4, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.1.1, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.MA-2, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SRG-OS-000467-GPOS-00211, SRG-OS-000468-GPOS-00212, 4.1.13, SV-204572r853985_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rename
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit rename tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rename
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for rename for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rename
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rename in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rename
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rename in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rename
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for rename for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rename
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rename in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rename
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rename in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rename
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="rename"
	KEY="delete"
	SYSCALL_GROUPING="unlink unlinkat rename renameat rmdir"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects File Deletion Events by User - renameat   [ref]

At a minimum, the audit system should collect file deletion events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S renameat -F auid>=1000 -F auid!=unset -F key=delete
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S renameat -F auid>=1000 -F auid!=unset -F key=delete
Rationale:
Auditing file deletions will create an audit trail for files that are removed from the system. The audit trail could aid in system troubleshooting, as well as, detecting malicious processes that attempt to delete log files to conceal their presence.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_file_deletion_events_renameat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-000366, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.4, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.1.1, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.MA-2, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SRG-OS-000467-GPOS-00211, SRG-OS-000468-GPOS-00212, 4.1.13, SV-204572r853985_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_renameat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit renameat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_renameat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for renameat for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - renameat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of renameat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - renameat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of renameat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_renameat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for renameat for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - renameat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of renameat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - renameat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of renameat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_renameat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="renameat"
	KEY="delete"
	SYSCALL_GROUPING="unlink unlinkat rename renameat rmdir"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects File Deletion Events by User - rmdir   [ref]

At a minimum, the audit system should collect file deletion events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rmdir -F auid>=1000 -F auid!=unset -F key=delete
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S rmdir -F auid>=1000 -F auid!=unset -F key=delete
Rationale:
Auditing file deletions will create an audit trail for files that are removed from the system. The audit trail could aid in system troubleshooting, as well as, detecting malicious processes that attempt to delete log files to conceal their presence.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_file_deletion_events_rmdir
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-000366, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.4, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.1.1, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.MA-2, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SRG-OS-000467-GPOS-00211, SRG-OS-000468-GPOS-00212, 4.1.14, SV-204572r853985_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rmdir
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit rmdir tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rmdir
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for rmdir for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rmdir
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rmdir in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rmdir
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rmdir in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rmdir
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for rmdir for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rmdir
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rmdir in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - rmdir
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of rmdir in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_rmdir
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="rmdir"
	KEY="delete"
	SYSCALL_GROUPING="unlink unlinkat rename renameat rmdir"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects File Deletion Events by User - unlinkat   [ref]

At a minimum, the audit system should collect file deletion events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S unlinkat -F auid>=1000 -F auid!=unset -F key=delete
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S unlinkat -F auid>=1000 -F auid!=unset -F key=delete
Rationale:
Auditing file deletions will create an audit trail for files that are removed from the system. The audit trail could aid in system troubleshooting, as well as, detecting malicious processes that attempt to delete log files to conceal their presence.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_file_deletion_events_unlinkat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-000366, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.4, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.1.1, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.MA-2, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SRG-OS-000467-GPOS-00211, SRG-OS-000468-GPOS-00212, 4.1.13, SV-204572r853985_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_unlinkat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit unlinkat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_unlinkat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for unlinkat for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - unlinkat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of unlinkat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - unlinkat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of unlinkat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_unlinkat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for unlinkat for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - unlinkat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of unlinkat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/delete.rules
    set_fact: audit_file="/etc/audit/rules.d/delete.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - unlinkat
      syscall_grouping:
      - unlink
      - unlinkat
      - rename
      - renameat
      - rmdir

  - name: Check existence of unlinkat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=delete
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030910
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_file_deletion_events_unlinkat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="unlinkat"
	KEY="delete"
	SYSCALL_GROUPING="unlink unlinkat rename renameat rmdir"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Record Unauthorized Access Attempts Events to Files (unsuccessful)   Group contains 6 rules
[ref]   At a minimum, the audit system should collect unauthorized file accesses for all users and root. Note that the "-F arch=b32" lines should be present even on a 64 bit system. These commands identify system calls for auditing. Even if the system is 64 bit it can still execute 32 bit system calls. Additionally, these rules can be configured in a number of ways while still achieving the desired effect. An example of this is that the "-S" calls could be split up and placed on separate lines, however, this is less efficient. Add the following to /etc/audit/audit.rules:
-a always,exit -F arch=b32 -S creat,open,openat,open_by_handle_at,truncate,ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
    -a always,exit -F arch=b32 -S creat,open,openat,open_by_handle_at,truncate,ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If your system is 64 bit then these lines should be duplicated and the arch=b32 replaced with arch=b64 as follows:
-a always,exit -F arch=b64 -S creat,open,openat,open_by_handle_at,truncate,ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
    -a always,exit -F arch=b64 -S creat,open,openat,open_by_handle_at,truncate,ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access

Rule   Record Unsuccessful Access Attempts to Files - creat   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S creat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S creat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S creat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S creat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S creat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S creat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S creat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S creat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_creat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.10, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit creat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for creat EACCES for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for creat EACCES for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for creat EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for creat EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - creat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of creat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_creat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="creat"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Unsuccessful Access Attempts to Files - ftruncate   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_ftruncate
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.10, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit ftruncate tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for ftruncate EACCES for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for ftruncate EACCES for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for ftruncate EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for ftruncate EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - ftruncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of ftruncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_ftruncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="ftruncate"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Unsuccessful Access Attempts to Files - open   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S open -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S open -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S open -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S open -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S open -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S open -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S open -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S open -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_open
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.10, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit open tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open EACCES for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open EACCES for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="open"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Unsuccessful Access Attempts to Files - open_by_handle_at   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S open_by_handle_at -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S open_by_handle_at -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S open_by_handle_at -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S open_by_handle_at -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S open_by_handle_at,truncate,ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S open_by_handle_at,truncate,ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S open_by_handle_at,truncate,ftruncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S open_by_handle_at,truncate,ftruncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_open_by_handle_at
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.11, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit open_by_handle_at tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open_by_handle_at EACCES for 32bit
    platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open_by_handle_at EACCES for 64bit
    platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open_by_handle_at EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for open_by_handle_at EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - open_by_handle_at
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of open_by_handle_at in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_open_by_handle_at
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="open_by_handle_at"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Unsuccessful Access Attempts to Files - openat   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S openat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S openat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S openat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S openat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S openat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S openat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S openat -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S openat -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_openat
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.10, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit openat tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for openat EACCES for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for openat EACCES for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for openat EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for openat EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - openat
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of openat in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_openat
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="openat"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Unsuccessful Access Attempts to Files - truncate   [ref]

At a minimum, the audit system should collect unauthorized file accesses for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F arch=b32 -S truncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S truncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S truncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S truncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file:
-a always,exit -F arch=b32 -S truncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b32 -S truncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
If the system is 64 bit then also add the following lines:
-a always,exit -F arch=b64 -S truncate -F exit=-EACCES -F auid>=1000 -F auid!=unset -F key=access
-a always,exit -F arch=b64 -S truncate -F exit=-EPERM -F auid>=1000 -F auid!=unset -F key=access
Warning:  Note that these rules can be configured in a number of ways while still achieving the desired effect. Here the system calls have been placed independent of other system calls. Grouping these system calls with others as identifying earlier in this guide is more efficient.
Rationale:
Unsuccessful attempts to access files could be an indicator of malicious activity on a system. Auditing these events could serve as evidence of potential system compromise.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_unsuccessful_file_modification_truncate
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.4, Req-10.2.1, 10.2.1.1, 10.2.1.4, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000064-GPOS-00033, SRG-OS-000458-GPOS-00203, SRG-OS-000461-GPOS-00205, 4.1.10, SV-204531r853917_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit truncate tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for truncate EACCES for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for truncate EACCES for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EACCES -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EACCES -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EACCES
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for truncate EPERM for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for truncate EPERM for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/access.rules
    set_fact: audit_file="/etc/audit/rules.d/access.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - truncate
      syscall_grouping:
      - creat
      - ftruncate
      - truncate
      - open
      - openat
      - open_by_handle_at

  - name: Check existence of truncate in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F exit=-EPERM -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F exit=-EPERM -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F exit=-EPERM
        -F auid>=1000 -F auid!=unset -F key=access
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030510
  - NIST-800-171-3.1.7
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.1
  - PCI-DSS-Req-10.2.4
  - PCI-DSSv4-10.2.1.1
  - PCI-DSSv4-10.2.1.4
  - audit_rules_unsuccessful_file_modification_truncate
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL="truncate"
KEY="access"
SYSCALL_GROUPING="creat ftruncate truncate open openat open_by_handle_at"

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EACCES"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS="-F exit=-EPERM"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Record Information on Kernel Modules Loading and Unloading   Group contains 3 rules
[ref]   To capture kernel module loading and unloading events, use following lines, setting ARCH to either b32 for 32-bit system, or having two lines for both b32 and b64 in case your system is 64-bit:
-a always,exit -F arch=ARCH -S init_module,delete_module -F key=modules
Place to add the lines depends on a way auditd daemon is configured. If it is configured to use the augenrules program (the default), add the lines to a file with suffix .rules in the directory /etc/audit/rules.d. If the auditd daemon is configured to use the auditctl utility, add the lines to file /etc/audit/audit.rules.

Rule   Ensure auditd Collects Information on Kernel Module Unloading - delete_module   [ref]

To capture kernel module unloading events, use following line, setting ARCH to either b32 for 32-bit system, or having two lines for both b32 and b64 in case your system is 64-bit:
-a always,exit -F arch=ARCH -S delete_module -F auid>=1000 -F auid!=unset -F key=modules
Place to add the line depends on a way auditd daemon is configured. If it is configured to use the augenrules program (the default), add the line to a file with suffix .rules in the directory /etc/audit/rules.d. If the auditd daemon is configured to use the auditctl utility, add the line to file /etc/audit/audit.rules.
Rationale:
The removal of kernel modules can be used to alter the behavior of the kernel and potentially introduce malicious code into kernel space. It is important to have an audit trail of modules that have been introduced into the kernel.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_kernel_module_loading_delete
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000471-GPOS-00216, SRG-OS-000477-GPOS-00222, 4.1.16, SV-204562r833175_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,-a%20always%2Cexit%20-F%20arch%3Db32%20-S%20delete_module%20-k%20module-change%0A-a%20always%2Cexit%20-F%20arch%3Db64%20-S%20delete_module%20-k%20module-change%0A
        mode: 0600
        path: /etc/audit/rules.d/75-kernel-module-loading-delete.rules
        overwrite: true

Complexity:low
Disruption:low
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030830
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_delete
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set architecture for audit delete_module tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030830
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_delete
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for delete_module for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - delete_module
      syscall_grouping: []

  - name: Check existence of delete_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - delete_module
      syscall_grouping: []

  - name: Check existence of delete_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030830
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_delete
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for delete_module for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - delete_module
      syscall_grouping: []

  - name: Check existence of delete_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - delete_module
      syscall_grouping: []

  - name: Check existence of delete_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030830
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_delete
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
# Note: 32-bit and 64-bit kernel syscall numbers not always line up =>
#       it's required on a 64-bit system to check also for the presence
#       of 32-bit's equivalent of the corresponding rule.
#       (See `man 7 audit.rules` for details )
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	
	SYSCALL="delete_module"
	KEY="modules"
	SYSCALL_GROUPING="delete_module"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on Kernel Module Loading and Unloading - finit_module   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d to capture kernel module loading and unloading events, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S finit_module -F auid>=1000 -F auid!=unset -F key=modules
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file in order to capture kernel module loading and unloading events, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S finit_module -F auid>=1000 -F auid!=unset -F key=modules
Rationale:
The addition/removal of kernel modules can be used to alter the behavior of the kernel and potentially introduce malicious code into kernel space. It is important to have an audit trail of modules that have been introduced into the kernel.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_kernel_module_loading_finit
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000471-GPOS-00216, SRG-OS-000477-GPOS-00222, 4.1.17, SV-204560r833172_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,-a%20always%2Cexit%20-F%20arch%3Db32%20-S%20finit_module%20-k%20module-change%0A-a%20always%2Cexit%20-F%20arch%3Db64%20-S%20finit_module%20-k%20module-change%0A
        mode: 0600
        path: /etc/audit/rules.d/75-kernel-module-loading-finit.rules
        overwrite: true

Complexity:low
Disruption:low
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_finit
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set architecture for audit finit_module tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_finit
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for finit_module for x86 platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - finit_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of finit_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - finit_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of finit_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_finit
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for finit_module for x86_64 platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - finit_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of finit_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - finit_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of finit_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_finit
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
# Note: 32-bit and 64-bit kernel syscall numbers not always line up =>
#       it's required on a 64-bit system to check also for the presence
#       of 32-bit's equivalent of the corresponding rule.
#       (See `man 7 audit.rules` for details )
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	
	SYSCALL="finit_module"
	KEY="modules"
	SYSCALL_GROUPING="init_module finit_module"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on Kernel Module Loading - init_module   [ref]

To capture kernel module loading events, use following line, setting ARCH to either b32 for 32-bit system, or having two lines for both b32 and b64 in case your system is 64-bit:
-a always,exit -F arch=ARCH -S init_module -F auid>=1000 -F auid!=unset -F key=modules
Place to add the line depends on a way auditd daemon is configured. If it is configured to use the augenrules program (the default), add the line to a file with suffix .rules in the directory /etc/audit/rules.d. If the auditd daemon is configured to use the auditctl utility, add the line to file /etc/audit/audit.rules.
Rationale:
The addition of kernel modules can be used to alter the behavior of the kernel and potentially introduce malicious code into kernel space. It is important to have an audit trail of modules that have been introduced into the kernel.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_kernel_module_loading_init
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000471-GPOS-00216, SRG-OS-000477-GPOS-00222, 4.1.16, SV-204560r833172_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,-a%20always%2Cexit%20-F%20arch%3Db32%20-S%20init_module%20-k%20module-change%0A-a%20always%2Cexit%20-F%20arch%3Db64%20-S%20init_module%20-k%20module-change%0A
        mode: 0600
        path: /etc/audit/rules.d/75-kernel-module-loading-init.rules
        overwrite: true

Complexity:low
Disruption:low
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_init
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set architecture for audit init_module tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_init
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for init_module for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - init_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of init_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - init_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of init_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_init
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Perform remediation of Audit rules for init_module for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - init_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of init_module in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/module-change.rules
    set_fact: audit_file="/etc/audit/rules.d/module-change.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - init_module
      syscall_grouping:
      - init_module
      - finit_module

  - name: Check existence of init_module in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=module-change
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - DISA-STIG-RHEL-07-030820
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_kernel_module_loading_init
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
# Note: 32-bit and 64-bit kernel syscall numbers not always line up =>
#       it's required on a 64-bit system to check also for the presence
#       of 32-bit's equivalent of the corresponding rule.
#       (See `man 7 audit.rules` for details )
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	
	SYSCALL="init_module"
	KEY="modules"
	SYSCALL_GROUPING="init_module finit_module"
	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Record Attempts to Alter Logon and Logout Events   Group contains 3 rules
Group   Record Information on the Use of Privileged Commands   Group contains 17 rules
[ref]   At a minimum, the audit system should collect the execution of privileged commands for all users and root.

Rule   Ensure auditd Collects Information on the Use of Privileged Commands   [ref]

The audit system should collect information about usage of privileged commands for all users. These are commands with suid or sgid bits on and they are specially risky in local block device partitions not mounted with noexec and nosuid options. Therefore, these partitions should be first identified by the following command:
findmnt -n -l -k -it $(awk '/nodev/ { print $2 }' /proc/filesystems | paste -sd,) | grep -Pv "noexec|nosuid"
For all partitions listed by the previous command, it is necessary to search for setuid / setgid programs using the following command:
$ sudo find PARTITION -xdev -perm /6000 -type f 2>/dev/null
For each setuid / setgid program identified by the previous command, an audit rule must be present in the appropriate place using the following line structure:
-a always,exit -F path=PROG_PATH -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup, add the line to a file with suffix .rules in the /etc/audit/rules.d directory, replacing the PROG_PATH part with the full path of that setuid / setgid identified program. If the auditd daemon is configured to use the auditctl utility instead, add the line to the /etc/audit/audit.rules file, also replacing the PROG_PATH part with the full path of that setuid / setgid identified program.
Warning:  This rule checks for multiple syscalls related to privileged commands. If needed to check specific privileged commands, other more specific rules should be considered. For example:
  • audit_rules_privileged_commands_su
  • audit_rules_privileged_commands_umount
  • audit_rules_privileged_commands_passwd
Warning:  Note that OVAL check and Bash / Ansible remediation of this rule explicitly excludes file systems mounted at
/proc
directory and its subdirectories. It is a virtual file system and it doesn't contain executable applications. At the same time, interacting with this file system during check or remediation caused undesirable errors.
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern that can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO08.04, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.05, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-002234, 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.5, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.3.4.5.9, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 3.9, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, 0582, 0584, 05885, 0586, 0846, 0957, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.1, A.16.1.2, A.16.1.3, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.3, A.6.2.1, A.6.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-2, DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, DE.DP-4, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, RS.CO-2, Req-10.2.2, 10.2.1.2, SRG-OS-000327-GPOS-00127, 4.1.11


Complexity:low
Disruption:low
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSSv4-10.2.1.2
  - audit_rules_privileged_commands
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure auditd Collects Information on the Use of Privileged Commands - Set
    List of Mount Points Which Permits Execution of Privileged Commands
  ansible.builtin.set_fact:
    privileged_mount_points: '{{(ansible_facts.mounts | rejectattr(''options'', ''search'',
      ''noexec|nosuid'') | rejectattr(''mount'', ''match'', ''/proc($|/.*$)'') | map(attribute=''mount'')
      | list ) }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSSv4-10.2.1.2
  - audit_rules_privileged_commands
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure auditd Collects Information on the Use of Privileged Commands - Search
    for Privileged Commands in Eligible Mount Points
  ansible.builtin.shell:
    cmd: find {{ item }} -xdev -perm /6000 -type f 2>/dev/null
  register: result_privileged_commands_search
  changed_when: false
  failed_when: false
  with_items: '{{ privileged_mount_points }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSSv4-10.2.1.2
  - audit_rules_privileged_commands
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure auditd Collects Information on the Use of Privileged Commands - Set
    List of Privileged Commands Found in Eligible Mount Points
  ansible.builtin.set_fact:
    privileged_commands: '{{( result_privileged_commands_search.results | map(attribute=''stdout_lines'')
      | select() | list )[-1] }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSSv4-10.2.1.2
  - audit_rules_privileged_commands
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure auditd Collects Information on the Use of Privileged Commands - Privileged
    Commands are Present in the System
  block:

  - name: Ensure auditd Collects Information on the Use of Privileged Commands - Ensure
      Rules for All Privileged Commands in augenrules Format
    ansible.builtin.lineinfile:
      path: /etc/audit/rules.d/privileged.rules
      line: -a always,exit -F path={{ item }} -F perm=x -F auid>=1000 -F auid!=unset
        -F key=privileged
      regexp: ^.*path={{ item | regex_escape() }} .*$
      create: true
    with_items:
    - '{{ privileged_commands }}'

  - name: Ensure auditd Collects Information on the Use of Privileged Commands - Ensure
      Rules for All Privileged Commands in auditctl Format
    ansible.builtin.lineinfile:
      path: /etc/audit/audit.rules
      line: -a always,exit -F path={{ item }} -F perm=x -F auid>=1000 -F auid!=unset
        -F key=privileged
      regexp: ^.*path={{ item | regex_escape() }} .*$
      create: true
    with_items:
    - '{{ privileged_commands }}'

  - name: Ensure auditd Collects Information on the Use of Privileged Commands - Search
      for Duplicated Rules in Other Files
    ansible.builtin.find:
      paths: /etc/audit/rules.d
      recurse: false
      contains: ^-a always,exit -F path={{ item }} .*$
      patterns: '*.rules'
    with_items:
    - '{{ privileged_commands }}'
    register: result_augenrules_files

  - name: Ensure auditd Collects Information on the Use of Privileged Commands - Ensure
      Rules for Privileged Commands are Defined Only in One File
    ansible.builtin.lineinfile:
      path: '{{ item.1.path }}'
      regexp: ^-a always,exit -F path={{ item.0.item }} .*$
      state: absent
    with_subelements:
    - '{{ result_augenrules_files.results }}'
    - files
    when:
    - item.1.path != '/etc/audit/rules.d/privileged.rules'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - privileged_commands is defined
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSSv4-10.2.1.2
  - audit_rules_privileged_commands
  - configure_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""

FILTER_NODEV=$(awk '/nodev/ { print $2 }' /proc/filesystems | paste -sd,)
PARTITIONS=$(findmnt -n -l -k -it $FILTER_NODEV | grep -Pv "noexec|nosuid|/proc($|/.*$)" | awk '{ print $1 }')
for PARTITION in $PARTITIONS; do
  PRIV_CMDS=$(find "${PARTITION}" -xdev -perm /6000 -type f 2>/dev/null)
  for PRIV_CMD in $PRIV_CMDS; do
    OTHER_FILTERS="-F path=$PRIV_CMD -F perm=x"
    # Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
    unset syscall_a
    unset syscall_grouping
    unset syscall_string
    unset syscall
    unset file_to_edit
    unset rule_to_edit
    unset rule_syscalls_to_edit
    unset other_string
    unset auid_string
    unset full_rule

    # Load macro arguments into arrays
    read -a syscall_a <<< $SYSCALL
    read -a syscall_grouping <<< $SYSCALL_GROUPING

    # Create a list of audit *.rules files that should be inspected for presence and correctness
    # of a particular audit rule. The scheme is as follows:
    #
    # -----------------------------------------------------------------------------------------
    #  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
    # -----------------------------------------------------------------------------------------
    #        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
    # -----------------------------------------------------------------------------------------
    #        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
    #        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
    # -----------------------------------------------------------------------------------------
    #
    files_to_inspect=()


    # If audit tool is 'augenrules', then check if the audit rule is defined
    # If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
    # If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
    default_file="/etc/audit/rules.d/$KEY.rules"
    # As other_filters may include paths, lets use a different delimiter for it
    # The "F" script expression tells sed to print the filenames where the expressions matched
    readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
    # Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
    if [ ${#files_to_inspect[@]} -eq "0" ]
    then
        file_to_inspect="/etc/audit/rules.d/$KEY.rules"
        files_to_inspect=("$file_to_inspect")
        if [ ! -e "$file_to_inspect" ]
        then
            touch "$file_to_inspect"
            chmod 0640 "$file_to_inspect"
        fi
    fi

    # After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
    skip=1

    for audit_file in "${files_to_inspect[@]}"
    do
        # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
        # i.e, collect rules that match:
        # * the action, list and arch, (2-nd argument)
        # * the other filters, (3-rd argument)
        # * the auid filters, (4-rd argument)
        readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

        candidate_rules=()
        # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
        for s_rule in "${similar_rules[@]}"
        do
            # Strip all the options and fields we know of,
            # than check if there was any field left over
            extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
            grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
        done

        if [[ ${#syscall_a[@]} -ge 1 ]]
        then
            # Check if the syscall we want is present in any of the similar existing rules
            for rule in "${candidate_rules[@]}"
            do
                rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
                all_syscalls_found=0
                for syscall in "${syscall_a[@]}"
                do
                    grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                       # A syscall was not found in the candidate rule
                       all_syscalls_found=1
                       }
                done
                if [[ $all_syscalls_found -eq 0 ]]
                then
                    # We found a rule with all the syscall(s) we want; skip rest of macro
                    skip=0
                    break
                fi

                # Check if this rule can be grouped with our target syscall and keep track of it
                for syscall_g in "${syscall_grouping[@]}"
                do
                    if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                    then
                        file_to_edit=${audit_file}
                        rule_to_edit=${rule}
                        rule_syscalls_to_edit=${rule_syscalls}
                    fi
                done
            done
        else
            # If there is any candidate rule, it is compliant; skip rest of macro
            if [ "${#candidate_rules[@]}" -gt 0 ]
            then
                skip=0
            fi
        fi

        if [ "$skip" -eq 0 ]; then
            break
        fi
    done

    if [ "$skip" -ne 0 ]; then
        # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
        # At this point we know if we need to either append the $full_rule or group
        # the syscall together with an exsiting rule

        # Append the full_rule if it cannot be grouped to any other rule
        if [ -z ${rule_to_edit+x} ]
        then
            # Build full_rule while avoid adding double spaces when other_filters is empty
            if [ "${#syscall_a[@]}" -gt 0 ]
            then
                syscall_string=""
                for syscall in "${syscall_a[@]}"
                do
                    syscall_string+=" -S $syscall"
                done
            fi
            other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
            auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
            full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
            echo "$full_rule" >> "$default_file"
            chmod o-rwx ${default_file}
        else
            # Check if the syscalls are declared as a comma separated list or
            # as multiple -S parameters
            if grep -q -- "," <<< "${rule_syscalls_to_edit}"
            then
                delimiter=","
            else
                delimiter=" -S "
            fi
            new_grouped_syscalls="${rule_syscalls_to_edit}"
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
                   # A syscall was not found in the candidate rule
                   new_grouped_syscalls+="${delimiter}${syscall}"
                   }
            done

            # Group the syscall in the rule
            sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
        fi
    fi
    unset syscall_a
    unset syscall_grouping
    unset syscall_string
    unset syscall
    unset file_to_edit
    unset rule_to_edit
    unset rule_syscalls_to_edit
    unset other_string
    unset auid_string
    unset full_rule

    # Load macro arguments into arrays
    read -a syscall_a <<< $SYSCALL
    read -a syscall_grouping <<< $SYSCALL_GROUPING

    # Create a list of audit *.rules files that should be inspected for presence and correctness
    # of a particular audit rule. The scheme is as follows:
    #
    # -----------------------------------------------------------------------------------------
    #  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
    # -----------------------------------------------------------------------------------------
    #        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
    # -----------------------------------------------------------------------------------------
    #        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
    #        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
    # -----------------------------------------------------------------------------------------
    #
    files_to_inspect=()



    # If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
    # file to the list of files to be inspected
    default_file="/etc/audit/audit.rules"
    files_to_inspect+=('/etc/audit/audit.rules' )

    # After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
    skip=1

    for audit_file in "${files_to_inspect[@]}"
    do
        # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
        # i.e, collect rules that match:
        # * the action, list and arch, (2-nd argument)
        # * the other filters, (3-rd argument)
        # * the auid filters, (4-rd argument)
        readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

        candidate_rules=()
        # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
        for s_rule in "${similar_rules[@]}"
        do
            # Strip all the options and fields we know of,
            # than check if there was any field left over
            extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
            grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
        done

        if [[ ${#syscall_a[@]} -ge 1 ]]
        then
            # Check if the syscall we want is present in any of the similar existing rules
            for rule in "${candidate_rules[@]}"
            do
                rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
                all_syscalls_found=0
                for syscall in "${syscall_a[@]}"
                do
                    grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                       # A syscall was not found in the candidate rule
                       all_syscalls_found=1
                       }
                done
                if [[ $all_syscalls_found -eq 0 ]]
                then
                    # We found a rule with all the syscall(s) we want; skip rest of macro
                    skip=0
                    break
                fi

                # Check if this rule can be grouped with our target syscall and keep track of it
                for syscall_g in "${syscall_grouping[@]}"
                do
                    if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                    then
                        file_to_edit=${audit_file}
                        rule_to_edit=${rule}
                        rule_syscalls_to_edit=${rule_syscalls}
                    fi
                done
            done
        else
            # If there is any candidate rule, it is compliant; skip rest of macro
            if [ "${#candidate_rules[@]}" -gt 0 ]
            then
                skip=0
            fi
        fi

        if [ "$skip" -eq 0 ]; then
            break
        fi
    done

    if [ "$skip" -ne 0 ]; then
        # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
        # At this point we know if we need to either append the $full_rule or group
        # the syscall together with an exsiting rule

        # Append the full_rule if it cannot be grouped to any other rule
        if [ -z ${rule_to_edit+x} ]
        then
            # Build full_rule while avoid adding double spaces when other_filters is empty
            if [ "${#syscall_a[@]}" -gt 0 ]
            then
                syscall_string=""
                for syscall in "${syscall_a[@]}"
                do
                    syscall_string+=" -S $syscall"
                done
            fi
            other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
            auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
            full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
            echo "$full_rule" >> "$default_file"
            chmod o-rwx ${default_file}
        else
            # Check if the syscalls are declared as a comma separated list or
            # as multiple -S parameters
            if grep -q -- "," <<< "${rule_syscalls_to_edit}"
            then
                delimiter=","
            else
                delimiter=" -S "
            fi
            new_grouped_syscalls="${rule_syscalls_to_edit}"
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
                   # A syscall was not found in the candidate rule
                   new_grouped_syscalls+="${delimiter}${syscall}"
                   }
            done

            # Group the syscall in the rule
            sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
        fi
    fi
  done
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - chage   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/chage -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/chage -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_chage
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000468-GPOS-00212, SRG-OS-000471-GPOS-00215, SV-204545r861035_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030660
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_chage
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/chage
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chage -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/chage -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chage -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chage -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/chage -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chage -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030660
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_chage
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/chage -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - chsh   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/chsh -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/chsh -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_chsh
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204551r861050_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030720
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_chsh
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/chsh
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chsh -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/chsh -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chsh -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/chsh -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/chsh -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/chsh -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030720
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_chsh
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/chsh -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - crontab   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/crontab -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/crontab -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_crontab
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204557r861068_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030800
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_crontab
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/crontab
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/crontab -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/crontab -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/crontab -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/crontab -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/crontab -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/crontab -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030800
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_crontab
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/crontab -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - gpasswd   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/gpasswd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/gpasswd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_gpasswd
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204544r861032_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030650
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_gpasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/gpasswd
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/gpasswd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/gpasswd -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/gpasswd -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/gpasswd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/gpasswd -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/gpasswd -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030650
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_gpasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/gpasswd -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - newgrp   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/newgrp -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/newgrp -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_newgrp
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000169, CCI-000135, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204550r861047_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030710
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_newgrp
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/newgrp
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/newgrp -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/newgrp -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/newgrp -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/newgrp -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/newgrp -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/newgrp -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030710
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_newgrp
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/newgrp -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - pam_timestamp_check   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/pam_timestamp_check
-F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/sbin/pam_timestamp_check
-F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_pam_timestamp_check
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204558r833166_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030810
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_pam_timestamp_check
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/pam_timestamp_check
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/pam_timestamp_check -F perm=x -F auid>=1000 -F auid!=unset
        (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/pam_timestamp_check
        -F perm=x -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/pam_timestamp_check
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/pam_timestamp_check -F perm=x -F auid>=1000 -F auid!=unset
        (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/pam_timestamp_check -F perm=x -F auid>=1000
        -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/pam_timestamp_check
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030810
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_pam_timestamp_check
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/pam_timestamp_check -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - passwd   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/passwd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/passwd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_passwd
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204542r861026_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030630
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/passwd
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/passwd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/passwd -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/passwd -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/passwd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/passwd -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/passwd -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030630
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/passwd -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - postdrop   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/postdrop -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/sbin/postdrop -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_postdrop
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204554r861059_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030760
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_postdrop
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/postdrop
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/postdrop -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/postdrop -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/postdrop -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/postdrop -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/postdrop -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/postdrop -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030760
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_postdrop
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/postdrop -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - postqueue   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/postqueue -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/sbin/postqueue -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_postqueue
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204555r861062_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030770
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_postqueue
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/postqueue
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/postqueue -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/postqueue -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/postqueue -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/postqueue -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/postqueue -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/postqueue -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030770
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_postqueue
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/postqueue -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - ssh-keysign   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/libexec/openssh/ssh-keysign -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/libexec/openssh/ssh-keysign -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_ssh_keysign
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204556r861065_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030780
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_ssh_keysign
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/libexec/openssh/ssh-keysign
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/libexec/openssh/ssh-keysign -F perm=x -F auid>=1000 -F auid!=unset
        (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/libexec/openssh/ssh-keysign
        -F perm=x -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/libexec/openssh/ssh-keysign
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/libexec/openssh/ssh-keysign -F perm=x -F auid>=1000 -F auid!=unset
        (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/libexec/openssh/ssh-keysign -F perm=x -F auid>=1000
        -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/libexec/openssh/ssh-keysign
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030780
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_ssh_keysign
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/libexec/openssh/ssh-keysign -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - su   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/su -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/su -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_su
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000064-GPOS-0003, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SV-204547r861041_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030680
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_su
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/su
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/su -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/su -F perm=x -F auid>=1000
        -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/su -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/su -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/su -F perm=x -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/su -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030680
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_su
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/su -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - sudo   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/sudo -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/sudo -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_sudo
Identifiers and References

References:  BP28(R19), 1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000466-GPOS-00210, SV-204548r861044_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030690
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_sudo
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/sudo
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/sudo -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/sudo -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/sudo -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/sudo -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/sudo -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/sudo -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030690
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_sudo
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/sudo -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - sudoedit   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/sudoedit -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/sudoedit -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_sudoedit
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_sudoedit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/sudoedit
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/sudoedit -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/sudoedit -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/sudoedit -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/sudoedit -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/sudoedit -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/sudoedit -F
        perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_sudoedit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/sudoedit -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - umount   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/bin/umount -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/bin/umount -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_umount
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000169, CCI-000135, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204553r861056_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030750
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_umount
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/bin/umount
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/umount -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/bin/umount -F perm=x -F
        auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/umount -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/bin/umount -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/bin/umount -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/bin/umount -F perm=x
        -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030750
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_umount
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/bin/umount -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - unix_chkpwd   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/unix_chkpwd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/sbin/unix_chkpwd -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_unix_chkpwd
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, CIP-007-3 R6.5, AC-2(4), AU-2(d), AU-3, AU-3.1, AU-12(a), AU-12(c), AU-12.1(ii), AU-12.1(iv), AC-6(9), CM-6(a), MA-4(1)(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204543r861029_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030640
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(a)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-12.1(ii)
  - NIST-800-53-AU-12.1(iv)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-AU-3.1
  - NIST-800-53-CM-6(a)
  - NIST-800-53-MA-4(1)(a)
  - audit_rules_privileged_commands_unix_chkpwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/unix_chkpwd
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/unix_chkpwd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/unix_chkpwd -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/unix_chkpwd
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/unix_chkpwd -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/unix_chkpwd -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/unix_chkpwd
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030640
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(a)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-12.1(ii)
  - NIST-800-53-AU-12.1(iv)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-AU-3.1
  - NIST-800-53-CM-6(a)
  - NIST-800-53-MA-4(1)(a)
  - audit_rules_privileged_commands_unix_chkpwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/unix_chkpwd -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on the Use of Privileged Commands - userhelper   [ref]

At a minimum, the audit system should collect the execution of privileged commands for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add a line of the following form to a file with suffix .rules in the directory /etc/audit/rules.d:
-a always,exit -F path=/usr/sbin/userhelper -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add a line of the following form to /etc/audit/audit.rules:
-a always,exit -F path=/usr/sbin/userhelper -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
Rationale:
Misuse of privileged functions, either intentionally or unintentionally by authorized users, or by unauthorized external entities that have compromised system accounts, is a serious and ongoing concern and can have significant adverse impacts on organizations. Auditing the use of privileged functions is one way to detect such misuse and identify the risk from insider and advanced persistent threats.

Privileged programs are subject to escalation-of-privilege attacks, which attempt to subvert their normal role of providing some necessary but limited capability. As such, motivation exists to monitor these programs for unusual activity.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_privileged_commands_userhelper
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, BAI03.05, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.PT-1, FAU_GEN.1.1.c, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SV-204546r861038_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030670
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_userhelper
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Perform remediation of Audit rules for /usr/sbin/userhelper
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/userhelper -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/privileged.rules
    set_fact: audit_file="/etc/audit/rules.d/privileged.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F path=/usr/sbin/userhelper -F perm=x
        -F auid>=1000 -F auid!=unset (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/userhelper
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls: []
      syscall_grouping: []

  - name: Check existence of  in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit(( -S |,)\w+)*(( -S |,){{ item }})+(( -S |,)\w+)* -F
        path=/usr/sbin/userhelper -F perm=x -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit)(?=.*(?:(?:-S |,)(?:{{ syscalls_found | join("|") }}))\b)((?:(
        -S |,)\w+)+)( -F path=/usr/sbin/userhelper -F perm=x -F auid>=1000 -F auid!=unset
        (?:-k |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit{{ syscalls | join(',') }} -F path=/usr/sbin/userhelper
        -F perm=x -F auid>=1000 -F auid!=unset -F key=privileged
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030670
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - audit_rules_privileged_commands_userhelper
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

ACTION_ARCH_FILTERS="-a always,exit"
OTHER_FILTERS="-F path=/usr/sbin/userhelper -F perm=x"
AUID_FILTERS="-F auid>=1000 -F auid!=unset"
SYSCALL=""
KEY="privileged"
SYSCALL_GROUPING=""
# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects Information on Exporting to Media (successful)   [ref]

At a minimum, the audit system should collect media exportation events for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S mount -F auid>=1000 -F auid!=unset -F key=export
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file, setting ARCH to either b32 or b64 as appropriate for your system:
-a always,exit -F arch=ARCH -S mount -F auid>=1000 -F auid!=unset -F key=export
Rationale:
The unauthorized exportation of data to external media could result in an information leak where classified information, Privacy Act information, and intellectual property could be lost. An audit trail should be created each time a filesystem is mounted to help identify and guard against information loss.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_media_export
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, Req-10.2.7, 10.2.1.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, 4.1.12, SV-204552r861053_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030740
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_media_export
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Set architecture for audit mount tasks
  set_fact:
    audit_arch: b64
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_architecture == "aarch64" or ansible_architecture == "ppc64" or ansible_architecture
    == "ppc64le" or ansible_architecture == "s390x" or ansible_architecture == "x86_64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030740
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_media_export
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for mount for 32bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - mount
      syscall_grouping: []

  - name: Check existence of mount in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - mount
      syscall_grouping: []

  - name: Check existence of mount in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b32(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b32)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b32 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030740
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_media_export
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Perform remediation of Audit rules for mount for 64bit platform
  block:

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - mount
      syscall_grouping: []

  - name: Check existence of mount in /etc/audit/rules.d/
    find:
      paths: /etc/audit/rules.d
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: '*.rules'
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Reset syscalls found per file
    set_fact:
      syscalls_per_file: {}
      found_paths_dict: {}

  - name: Declare syscalls found per file
    set_fact: syscalls_per_file="{{ syscalls_per_file | combine( {item.files[0].path
      :[item.item] + syscalls_per_file.get(item.files[0].path, []) } ) }}"
    loop: '{{ find_command.results | selectattr(''matched'') | list }}'

  - name: Declare files where syscalls were found
    set_fact: found_paths="{{ find_command.results | map(attribute='files') | flatten
      | map(attribute='path') | list }}"

  - name: Count occurrences of syscalls in paths
    set_fact: found_paths_dict="{{ found_paths_dict | combine({ item:1+found_paths_dict.get(item,
      0) }) }}"
    loop: '{{ find_command.results | map(attribute=''files'') | flatten | map(attribute=''path'')
      | list }}'

  - name: Get path with most syscalls
    set_fact: audit_file="{{ (found_paths_dict | dict2items() | sort(attribute='value')
      | last).key }}"
    when: found_paths | length >= 1

  - name: No file with syscall found, set path to /etc/audit/rules.d/perm_mod.rules
    set_fact: audit_file="/etc/audit/rules.d/perm_mod.rules"
    when: found_paths | length == 0

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_per_file[audit_file]
        | join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k
        |-F key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0

  - name: Declare list of syscalls
    set_fact:
      syscalls:
      - mount
      syscall_grouping: []

  - name: Check existence of mount in /etc/audit/audit.rules
    find:
      paths: /etc/audit
      contains: -a always,exit -F arch=b64(( -S |,)\w+)*(( -S |,){{ item }})+(( -S
        |,)\w+)* -F auid>=1000 -F auid!=unset (-k\s+|-F\s+key=)\S+\s*$
      patterns: audit.rules
    register: find_command
    loop: '{{ (syscall_grouping + syscalls) | unique }}'

  - name: Set path to /etc/audit/audit.rules
    set_fact: audit_file="/etc/audit/audit.rules"

  - name: Declare found syscalls
    set_fact: syscalls_found="{{ find_command.results | selectattr('matched') | map(attribute='item')
      | list }}"

  - name: Declare missing syscalls
    set_fact: missing_syscalls="{{ syscalls | difference(syscalls_found) }}"

  - name: Replace the audit rule in {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      regexp: (-a always,exit -F arch=b64)(?=.*(?:(?:-S |,)(?:{{ syscalls_found |
        join("|") }}))\b)((?:( -S |,)\w+)+)( -F auid>=1000 -F auid!=unset (?:-k |-F
        key=)\w+)
      line: \1\2\3{{ missing_syscalls | join("\3") }}\4
      backrefs: true
      state: present
    when: syscalls_found | length > 0 and missing_syscalls | length > 0

  - name: Add the audit rule to {{ audit_file }}
    lineinfile:
      path: '{{ audit_file }}'
      line: -a always,exit -F arch=b64 -S {{ syscalls | join(',') }} -F auid>=1000
        -F auid!=unset -F key=perm_mod
      create: true
      mode: o-rwx
      state: present
    when: syscalls_found | length == 0
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - audit_arch == "b64"
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030740
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.7
  - PCI-DSSv4-10.2.1.7
  - audit_rules_media_export
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# First perform the remediation of the syscall rule
# Retrieve hardware architecture of the underlying system
[ "$(getconf LONG_BIT)" = "32" ] && RULE_ARCHS=("b32") || RULE_ARCHS=("b32" "b64")

for ARCH in "${RULE_ARCHS[@]}"
do
	ACTION_ARCH_FILTERS="-a always,exit -F arch=$ARCH"
	OTHER_FILTERS=""
	AUID_FILTERS="-F auid>=1000 -F auid!=unset"
	SYSCALL="mount"
	KEY="perm_mod"
	SYSCALL_GROUPING=""

	# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()


# If audit tool is 'augenrules', then check if the audit rule is defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to the list for inspection
# If rule isn't defined yet, add '/etc/audit/rules.d/$key.rules' to the list for inspection
default_file="/etc/audit/rules.d/$KEY.rules"
# As other_filters may include paths, lets use a different delimiter for it
# The "F" script expression tells sed to print the filenames where the expressions matched
readarray -t files_to_inspect < <(sed -s -n -e "/^$ACTION_ARCH_FILTERS/!d" -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" -e "F" /etc/audit/rules.d/*.rules)
# Case when particular rule isn't defined in /etc/audit/rules.d/*.rules yet
if [ ${#files_to_inspect[@]} -eq "0" ]
then
    file_to_inspect="/etc/audit/rules.d/$KEY.rules"
    files_to_inspect=("$file_to_inspect")
    if [ ! -e "$file_to_inspect" ]
    then
        touch "$file_to_inspect"
        chmod 0640 "$file_to_inspect"
    fi
fi

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
	unset syscall_a
unset syscall_grouping
unset syscall_string
unset syscall
unset file_to_edit
unset rule_to_edit
unset rule_syscalls_to_edit
unset other_string
unset auid_string
unset full_rule

# Load macro arguments into arrays
read -a syscall_a <<< $SYSCALL
read -a syscall_grouping <<< $SYSCALL_GROUPING

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
#  Tool used to load audit rules | Rule already defined  |  Audit rules file to inspect    |
# -----------------------------------------------------------------------------------------
#        auditctl                |     Doesn't matter    |  /etc/audit/audit.rules         |
# -----------------------------------------------------------------------------------------
#        augenrules              |          Yes          |  /etc/audit/rules.d/*.rules     |
#        augenrules              |          No           |  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
#
files_to_inspect=()



# If audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# file to the list of files to be inspected
default_file="/etc/audit/audit.rules"
files_to_inspect+=('/etc/audit/audit.rules' )

# After converting to jinja, we cannot return; therefore we skip the rest of the macro if needed instead
skip=1

for audit_file in "${files_to_inspect[@]}"
do
    # Filter existing $audit_file rules' definitions to select those that satisfy the rule pattern,
    # i.e, collect rules that match:
    # * the action, list and arch, (2-nd argument)
    # * the other filters, (3-rd argument)
    # * the auid filters, (4-rd argument)
    readarray -t similar_rules < <(sed -e "/^$ACTION_ARCH_FILTERS/!d"  -e "\#$OTHER_FILTERS#!d" -e "/$AUID_FILTERS/!d" "$audit_file")

    candidate_rules=()
    # Filter out rules that have more fields then required. This will remove rules more specific than the required scope
    for s_rule in "${similar_rules[@]}"
    do
        # Strip all the options and fields we know of,
        # than check if there was any field left over
        extra_fields=$(sed -E -e "s/^$ACTION_ARCH_FILTERS//"  -e "s#$OTHER_FILTERS##" -e "s/$AUID_FILTERS//" -e "s/((:?-S [[:alnum:],]+)+)//g" -e "s/-F key=\w+|-k \w+//"<<< "$s_rule")
        grep -q -- "-F" <<< "$extra_fields" || candidate_rules+=("$s_rule")
    done

    if [[ ${#syscall_a[@]} -ge 1 ]]
    then
        # Check if the syscall we want is present in any of the similar existing rules
        for rule in "${candidate_rules[@]}"
        do
            rule_syscalls=$(echo "$rule" | grep -o -P '(-S [\w,]+)+' | xargs)
            all_syscalls_found=0
            for syscall in "${syscall_a[@]}"
            do
                grep -q -- "\b${syscall}\b" <<< "$rule_syscalls" || {
                   # A syscall was not found in the candidate rule
                   all_syscalls_found=1
                   }
            done
            if [[ $all_syscalls_found -eq 0 ]]
            then
                # We found a rule with all the syscall(s) we want; skip rest of macro
                skip=0
                break
            fi

            # Check if this rule can be grouped with our target syscall and keep track of it
            for syscall_g in "${syscall_grouping[@]}"
            do
                if grep -q -- "\b${syscall_g}\b" <<< "$rule_syscalls"
                then
                    file_to_edit=${audit_file}
                    rule_to_edit=${rule}
                    rule_syscalls_to_edit=${rule_syscalls}
                fi
            done
        done
    else
        # If there is any candidate rule, it is compliant; skip rest of macro
        if [ "${#candidate_rules[@]}" -gt 0 ]
        then
            skip=0
        fi
    fi

    if [ "$skip" -eq 0 ]; then
        break
    fi
done

if [ "$skip" -ne 0 ]; then
    # We checked all rules that matched the expected resemblance pattern (action, arch & auid)
    # At this point we know if we need to either append the $full_rule or group
    # the syscall together with an exsiting rule

    # Append the full_rule if it cannot be grouped to any other rule
    if [ -z ${rule_to_edit+x} ]
    then
        # Build full_rule while avoid adding double spaces when other_filters is empty
        if [ "${#syscall_a[@]}" -gt 0 ]
        then
            syscall_string=""
            for syscall in "${syscall_a[@]}"
            do
                syscall_string+=" -S $syscall"
            done
        fi
        other_string=$([[ $OTHER_FILTERS ]] && echo " $OTHER_FILTERS") || /bin/true
        auid_string=$([[ $AUID_FILTERS ]] && echo " $AUID_FILTERS") || /bin/true
        full_rule="$ACTION_ARCH_FILTERS${syscall_string}${other_string}${auid_string} -F key=$KEY" || /bin/true
        echo "$full_rule" >> "$default_file"
        chmod o-rwx ${default_file}
    else
        # Check if the syscalls are declared as a comma separated list or
        # as multiple -S parameters
        if grep -q -- "," <<< "${rule_syscalls_to_edit}"
        then
            delimiter=","
        else
            delimiter=" -S "
        fi
        new_grouped_syscalls="${rule_syscalls_to_edit}"
        for syscall in "${syscall_a[@]}"
        do
            grep -q -- "\b${syscall}\b" <<< "${rule_syscalls_to_edit}" || {
               # A syscall was not found in the candidate rule
               new_grouped_syscalls+="${delimiter}${syscall}"
               }
        done

        # Group the syscall in the rule
        sed -i -e "\#${rule_to_edit}#s#${rule_syscalls_to_edit}#${new_grouped_syscalls}#" "$file_to_edit"
    fi
fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure auditd Collects System Administrator Actions   [ref]

At a minimum, the audit system should collect administrator actions for all users and root. If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to a file with suffix .rules in the directory /etc/audit/rules.d:
-w /etc/sudoers -p wa -k actions
-w /etc/sudoers.d/ -p wa -k actions
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to /etc/audit/audit.rules file:
-w /etc/sudoers -p wa -k actions
-w /etc/sudoers.d/ -p wa -k actions
Rationale:
The actions taken by system administrators should be audited to keep a record of what was executed on the system, as well as, for accountability purposes.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_sysadmin_actions
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000126, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, AC-2(7)(b), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.2, Req-10.2.5.b, 10.2.1.5, 10.2.2, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000304-GPOS-00121, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, 4.1.14, SV-204549r853953_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,{{ -w%20/etc/sudoers.d/%20-p%20wa%20-k%20actions%0A-w%20/etc/sudoers%20-p%20wa%20-k%20actions%0A }}
        mode: 0600
        path: /etc/audit/rules.d/75-audit-sysadmin-actions.rules
        overwrite: true

Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Check if watch rule for /etc/sudoers already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/sudoers\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key actions
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)actions$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Use /etc/audit/rules.d/actions.rules as the recipient for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/actions.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Add watch rule for /etc/sudoers in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/sudoers -p wa -k actions
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Check if watch rule for /etc/sudoers already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/sudoers\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Add watch rule for /etc/sudoers in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/sudoers -p wa -k actions
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Check if watch rule for /etc/sudoers.d/ already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/sudoers.d/\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key actions
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)actions$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Use /etc/audit/rules.d/actions.rules as the recipient for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/actions.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Add watch rule for /etc/sudoers.d/ in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/sudoers.d/ -p wa -k actions
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Check if watch rule for /etc/sudoers.d/ already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/sudoers.d/\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Add watch rule for /etc/sudoers.d/ in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/sudoers.d/ -p wa -k actions
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030700
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(7)(b)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.2
  - PCI-DSS-Req-10.2.5.b
  - PCI-DSSv4-10.2.1.5
  - PCI-DSSv4-10.2.2
  - audit_rules_sysadmin_actions
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/sudoers" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/sudoers $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/sudoers$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/sudoers -p wa -k actions" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/actions.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/sudoers" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/actions.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/actions.rules"
    # If the actions.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/sudoers" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/sudoers $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/sudoers$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/sudoers -p wa -k actions" >> "$audit_rules_file"
    fi
done

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/sudoers.d/" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/sudoers.d/ $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/sudoers.d/$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/sudoers.d/ -p wa -k actions" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/actions.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/sudoers.d/" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/actions.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/actions.rules"
    # If the actions.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/sudoers.d/" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/sudoers.d/ $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/sudoers.d/$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/sudoers.d/ -p wa -k actions" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Shutdown System When Auditing Failures Occur   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following line to to the bottom of a file with suffix .rules in the directory /etc/audit/rules.d:
-f 2
If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following line to the bottom of the /etc/audit/audit.rules file:
-f 2
Rationale:
It is critical for the appropriate personnel to be aware if a system is at risk of failing to process audit logs as required. Without this notification, the security personnel may be unaware of an impending failure of the audit capability, and system operation may be adversely affected.

Audit processing failures include software/hardware errors, failures in the audit capturing mechanisms, and audit storage capacity being reached or exceeded.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_system_shutdown
Identifiers and References

References:  1, 14, 15, 16, 3, 5, 6, APO11.04, BAI03.05, DSS05.04, DSS05.07, MEA02.01, 3.3.1, 3.3.4, CCI-000139, CCI-000140, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, AU-5(b), SC-24, CM-6(a), PR.PT-1, SRG-OS-000046-GPOS-00022, SRG-OS-000047-GPOS-00023, SV-204504r880761_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - DISA-STIG-RHEL-07-030010
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.4
  - NIST-800-53-AU-5(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-24
  - audit_rules_system_shutdown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy
- name: XCCDF Value var_audit_failure_mode # promote to variable
  set_fact:
    var_audit_failure_mode: !!str 2
  tags:
    - always

- name: Collect all files from /etc/audit/rules.d with .rules extension
  find:
    paths: /etc/audit/rules.d/
    patterns: '*.rules'
  register: find_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030010
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.4
  - NIST-800-53-AU-5(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-24
  - audit_rules_system_shutdown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Remove the -f option from all Audit config files
  lineinfile:
    path: '{{ item }}'
    regexp: ^\s*(?:-f)\s+.*$
    state: absent
  loop: '{{ find_rules_d.files | map(attribute=''path'') | list + [''/etc/audit/audit.rules'']
    }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030010
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.4
  - NIST-800-53-AU-5(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-24
  - audit_rules_system_shutdown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add Audit -f option into /etc/audit/rules.d/immutable.rules and /etc/audit/audit.rules
  lineinfile:
    path: '{{ item }}'
    create: true
    line: -f {{ var_audit_failure_mode }}
  loop:
  - /etc/audit/audit.rules
  - /etc/audit/rules.d/immutable.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-030010
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.4
  - NIST-800-53-AU-5(b)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-24
  - audit_rules_system_shutdown
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

var_audit_failure_mode='2'


# Traverse all of:
#
# /etc/audit/audit.rules,			(for auditctl case)
# /etc/audit/rules.d/*.rules			(for augenrules case)
find /etc/audit /etc/audit/rules.d -maxdepth 1 -type f -name '*.rules' -exec sed -i '/-f[[:space:]]\+.*/d' {} ';'

for AUDIT_FILE in "/etc/audit/audit.rules" "/etc/audit/rules.d/immutable.rules"
do
	echo '' >> $AUDIT_FILE
	echo '# Set the audit.rules configuration to halt system upon audit failure per security requirements' >> $AUDIT_FILE
	echo "-f $var_audit_failure_mode" >> $AUDIT_FILE
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify User/Group Information - /etc/group   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d, in order to capture events that modify account changes:

-w /etc/group -p wa -k audit_rules_usergroup_modification


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file, in order to capture events that modify account changes:

-w /etc/group -p wa -k audit_rules_usergroup_modification
Rationale:
In addition to auditing new user and group accounts, these watches will alert the system administrator(s) to any modifications. Any unexpected users, groups, or modifications should be investigated for legitimacy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_usergroup_modification_group
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000018, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-001403, CCI-001404, CCI-001405, CCI-001683, CCI-001684, CCI-001685, CCI-001686, CCI-002130, CCI-002132, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.5, 10.2.1.5, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, 4.1.4, SV-204565r853979_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/group already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/group\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key audit_rules_usergroup_modification
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)audit_rules_usergroup_modification$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use /etc/audit/rules.d/audit_rules_usergroup_modification.rules as the recipient
    for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/audit_rules_usergroup_modification.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/group in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/group -p wa -k audit_rules_usergroup_modification
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/group already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/group\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/group in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/group -p wa -k audit_rules_usergroup_modification
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030871
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_group
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/group" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/group $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/group$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/group -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/group" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/audit_rules_usergroup_modification.rules"
    # If the audit_rules_usergroup_modification.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/group" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/group $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/group$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/group -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify User/Group Information - /etc/gshadow   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d, in order to capture events that modify account changes:

-w /etc/gshadow -p wa -k audit_rules_usergroup_modification


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file, in order to capture events that modify account changes:

-w /etc/gshadow -p wa -k audit_rules_usergroup_modification
Rationale:
In addition to auditing new user and group accounts, these watches will alert the system administrator(s) to any modifications. Any unexpected users, groups, or modifications should be investigated for legitimacy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_usergroup_modification_gshadow
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000018, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-001403, CCI-001404, CCI-001405, CCI-001683, CCI-001684, CCI-001685, CCI-001686, CCI-002130, CCI-002132, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.5, 10.2.1.5, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, 4.1.4, SV-204566r853980_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/gshadow already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/gshadow\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key audit_rules_usergroup_modification
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)audit_rules_usergroup_modification$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use /etc/audit/rules.d/audit_rules_usergroup_modification.rules as the recipient
    for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/audit_rules_usergroup_modification.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/gshadow in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/gshadow -p wa -k audit_rules_usergroup_modification
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/gshadow already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/gshadow\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/gshadow in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/gshadow -p wa -k audit_rules_usergroup_modification
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030872
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/gshadow" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/gshadow $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/gshadow$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/gshadow -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/gshadow" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/audit_rules_usergroup_modification.rules"
    # If the audit_rules_usergroup_modification.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/gshadow" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/gshadow $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/gshadow$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/gshadow -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify User/Group Information - /etc/security/opasswd   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d, in order to capture events that modify account changes:

-w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file, in order to capture events that modify account changes:

-w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification
Rationale:
In addition to auditing new user and group accounts, these watches will alert the system administrator(s) to any modifications. Any unexpected users, groups, or modifications should be investigated for legitimacy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_usergroup_modification_opasswd
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000018, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-001403, CCI-001404, CCI-001405, CCI-001683, CCI-001684, CCI-001685, CCI-001686, CCI-002130, CCI-002132, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.5, 10.2.1.5, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, 4.1.4, SV-204568r853982_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/security/opasswd already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/security/opasswd\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key audit_rules_usergroup_modification
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)audit_rules_usergroup_modification$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use /etc/audit/rules.d/audit_rules_usergroup_modification.rules as the recipient
    for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/audit_rules_usergroup_modification.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/security/opasswd in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/security/opasswd already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/security/opasswd\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/security/opasswd in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030874
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_opasswd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/security/opasswd" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/security/opasswd $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/security/opasswd$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/security/opasswd" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/audit_rules_usergroup_modification.rules"
    # If the audit_rules_usergroup_modification.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/security/opasswd" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/security/opasswd $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/security/opasswd$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/security/opasswd -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify User/Group Information - /etc/passwd   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d, in order to capture events that modify account changes:

-w /etc/passwd -p wa -k audit_rules_usergroup_modification


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file, in order to capture events that modify account changes:

-w /etc/passwd -p wa -k audit_rules_usergroup_modification
Rationale:
In addition to auditing new user and group accounts, these watches will alert the system administrator(s) to any modifications. Any unexpected users, groups, or modifications should be investigated for legitimacy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_usergroup_modification_passwd
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000018, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-001403, CCI-001404, CCI-001405, CCI-001683, CCI-001684, CCI-001685, CCI-001686, CCI-002130, CCI-002132, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.5, 10.2.1.5, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000304-GPOS-00121, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, SRG-OS-000274-GPOS-00104, SRG-OS-000275-GPOS-00105, SRG-OS-000276-GPOS-00106, SRG-OS-000277-GPOS-00107, 4.1.4, SV-204564r853978_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/passwd already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/passwd\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key audit_rules_usergroup_modification
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)audit_rules_usergroup_modification$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use /etc/audit/rules.d/audit_rules_usergroup_modification.rules as the recipient
    for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/audit_rules_usergroup_modification.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/passwd in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/passwd -p wa -k audit_rules_usergroup_modification
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/passwd already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/passwd\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/passwd in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/passwd -p wa -k audit_rules_usergroup_modification
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030870
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/passwd" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/passwd $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/passwd$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/passwd -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/passwd" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/audit_rules_usergroup_modification.rules"
    # If the audit_rules_usergroup_modification.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/passwd" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/passwd $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/passwd$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/passwd -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Record Events that Modify User/Group Information - /etc/shadow   [ref]

If the auditd daemon is configured to use the augenrules program to read audit rules during daemon startup (the default), add the following lines to a file with suffix .rules in the directory /etc/audit/rules.d, in order to capture events that modify account changes:

-w /etc/shadow -p wa -k audit_rules_usergroup_modification


If the auditd daemon is configured to use the auditctl utility to read audit rules during daemon startup, add the following lines to /etc/audit/audit.rules file, in order to capture events that modify account changes:

-w /etc/shadow -p wa -k audit_rules_usergroup_modification
Rationale:
In addition to auditing new user and group accounts, these watches will alert the system administrator(s) to any modifications. Any unexpected users, groups, or modifications should be investigated for legitimacy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_audit_rules_usergroup_modification_shadow
Identifiers and References

References:  BP28(R73), 1, 11, 12, 13, 14, 15, 16, 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS06.03, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.1.7, CCI-000018, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-001403, CCI-001404, CCI-001405, CCI-001683, CCI-001684, CCI-001685, CCI-001686, CCI-002130, CCI-002132, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(3)(ii)(A), 164.308(a)(5)(ii)(C), 164.312(a)(2)(i), 164.312(b), 164.312(d), 164.312(e), 4.2.3.10, 4.3.2.6.7, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.8, 4.3.3.6.6, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.2, CIP-004-6 R2.2.3, CIP-007-3 R.1.3, CIP-007-3 R5, CIP-007-3 R5.1.1, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, AC-2(4), AU-2(d), AU-12(c), AC-6(9), CM-6(a), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1.1.c, Req-10.2.5, 10.2.1.5, SRG-OS-000004-GPOS-00004, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000304-GPOS-00121, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000470-GPOS-00214, SRG-OS-000471-GPOS-00215, SRG-OS-000239-GPOS-00089, SRG-OS-000240-GPOS-00090, SRG-OS-000241-GPOS-00091, SRG-OS-000303-GPOS-00120, SRG-OS-000466-GPOS-00210, SRG-OS-000476-GPOS-00221, 4.1.4, SV-204567r853981_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/shadow already exists in /etc/audit/rules.d/
  find:
    paths: /etc/audit/rules.d
    contains: ^\s*-w\s+/etc/shadow\s+-p\s+wa(\s|$)+
    patterns: '*.rules'
  register: find_existing_watch_rules_d
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Search /etc/audit/rules.d for other rules with specified key audit_rules_usergroup_modification
  find:
    paths: /etc/audit/rules.d
    contains: ^.*(?:-F key=|-k\s+)audit_rules_usergroup_modification$
    patterns: '*.rules'
  register: find_watch_key
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use /etc/audit/rules.d/audit_rules_usergroup_modification.rules as the recipient
    for the rule
  set_fact:
    all_files:
    - /etc/audit/rules.d/audit_rules_usergroup_modification.rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched == 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Use matched file as the recipient for the rule
  set_fact:
    all_files:
    - '{{ find_watch_key.files | map(attribute=''path'') | list | first }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_watch_key.matched is defined and find_watch_key.matched > 0 and find_existing_watch_rules_d.matched
    is defined and find_existing_watch_rules_d.matched == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/shadow in /etc/audit/rules.d/
  lineinfile:
    path: '{{ all_files[0] }}'
    line: -w /etc/shadow -p wa -k audit_rules_usergroup_modification
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_rules_d.matched is defined and find_existing_watch_rules_d.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Check if watch rule for /etc/shadow already exists in /etc/audit/audit.rules
  find:
    paths: /etc/audit/
    contains: ^\s*-w\s+/etc/shadow\s+-p\s+wa(\s|$)+
    patterns: audit.rules
  register: find_existing_watch_audit_rules
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

- name: Add watch rule for /etc/shadow in /etc/audit/audit.rules
  lineinfile:
    line: -w /etc/shadow -p wa -k audit_rules_usergroup_modification
    state: present
    dest: /etc/audit/audit.rules
    create: true
    mode: '0640'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - find_existing_watch_audit_rules.matched is defined and find_existing_watch_audit_rules.matched
    == 0
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030873
  - NIST-800-171-3.1.7
  - NIST-800-53-AC-2(4)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.2.5
  - PCI-DSSv4-10.2.1.5
  - audit_rules_usergroup_modification_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

# Perform the remediation for both possible tools: 'auditctl' and 'augenrules'

# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()


# If the audit tool is 'auditctl', then add '/etc/audit/audit.rules'
# into the list of files to be inspected
files_to_inspect+=('/etc/audit/audit.rules')

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/shadow" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/shadow $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/shadow$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/shadow -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done
# Create a list of audit *.rules files that should be inspected for presence and correctness
# of a particular audit rule. The scheme is as follows:
#
# -----------------------------------------------------------------------------------------
# Tool used to load audit rules	| Rule already defined	|  Audit rules file to inspect	  |
# -----------------------------------------------------------------------------------------
#	auditctl		|     Doesn't matter	|  /etc/audit/audit.rules	  |
# -----------------------------------------------------------------------------------------
# 	augenrules		|          Yes		|  /etc/audit/rules.d/*.rules	  |
# 	augenrules		|          No		|  /etc/audit/rules.d/$key.rules  |
# -----------------------------------------------------------------------------------------
files_to_inspect=()

# If the audit is 'augenrules', then check if rule is already defined
# If rule is defined, add '/etc/audit/rules.d/*.rules' to list of files for inspection.
# If rule isn't defined, add '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' to list of files for inspection.
readarray -t matches < <(grep -HP "[\s]*-w[\s]+/etc/shadow" /etc/audit/rules.d/*.rules)

# For each of the matched entries
for match in "${matches[@]}"
do
    # Extract filepath from the match
    rulesd_audit_file=$(echo $match | cut -f1 -d ':')
    # Append that path into list of files for inspection
    files_to_inspect+=("$rulesd_audit_file")
done
# Case when particular audit rule isn't defined yet
if [ "${#files_to_inspect[@]}" -eq "0" ]
then
    # Append '/etc/audit/rules.d/audit_rules_usergroup_modification.rules' into list of files for inspection
    key_rule_file="/etc/audit/rules.d/audit_rules_usergroup_modification.rules"
    # If the audit_rules_usergroup_modification.rules file doesn't exist yet, create it with correct permissions
    if [ ! -e "$key_rule_file" ]
    then
        touch "$key_rule_file"
        chmod 0640 "$key_rule_file"
    fi
    files_to_inspect+=("$key_rule_file")
fi

# Finally perform the inspection and possible subsequent audit rule
# correction for each of the files previously identified for inspection
for audit_rules_file in "${files_to_inspect[@]}"
do
    # Check if audit watch file system object rule for given path already present
    if grep -q -P -- "^[\s]*-w[\s]+/etc/shadow" "$audit_rules_file"
    then
        # Rule is found => verify yet if existing rule definition contains
        # all of the required access type bits

        # Define BRE whitespace class shortcut
        sp="[[:space:]]"
        # Extract current permission access types (e.g. -p [r|w|x|a] values) from audit rule
        current_access_bits=$(sed -ne "s#$sp*-w$sp\+/etc/shadow $sp\+-p$sp\+\([rxwa]\{1,4\}\).*#\1#p" "$audit_rules_file")
        # Split required access bits string into characters array
        # (to check bit's presence for one bit at a time)
        for access_bit in $(echo "wa" | grep -o .)
        do
            # For each from the required access bits (e.g. 'w', 'a') check
            # if they are already present in current access bits for rule.
            # If not, append that bit at the end
            if ! grep -q "$access_bit" <<< "$current_access_bits"
            then
                # Concatenate the existing mask with the missing bit
                current_access_bits="$current_access_bits$access_bit"
            fi
        done
        # Propagate the updated rule's access bits (original + the required
        # ones) back into the /etc/audit/audit.rules file for that rule
        sed -i "s#\($sp*-w$sp\+/etc/shadow$sp\+-p$sp\+\)\([rxwa]\{1,4\}\)\(.*\)#\1$current_access_bits\3#" "$audit_rules_file"
    else
        # Rule isn't present yet. Append it at the end of $audit_rules_file file
        # with proper key

        echo "-w /etc/shadow -p wa -k audit_rules_usergroup_modification" >> "$audit_rules_file"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   System Audit Logs Must Be Owned By Root   [ref]

All audit logs must be owned by root user and group. By default, the path for audit log is
/var/log/audit/
. To properly set the owner of /var/log/audit, run the command:
$ sudo chown root /var/log/audit 
To properly set the owner of /var/log/audit/*, run the command:
$ sudo chown root /var/log/audit/* 
Rationale:
Unauthorized disclosure of audit records can reveal system and configuration data to attackers, thus compromising its confidentiality.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_ownership_var_log_audit
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 19, 3, 4, 5, 6, 7, 8, 5.4.1.1, APO01.06, APO11.04, APO12.06, BAI03.05, BAI08.02, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS05.04, DSS05.07, DSS06.02, MEA02.01, 3.3.1, CCI-000162, CCI-000163, CCI-000164, CCI-001314, 4.2.3.10, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.7.3, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 5.2, SR 6.1, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), AU-9(4), DE.AE-3, DE.AE-5, PR.AC-4, PR.DS-5, PR.PT-1, RS.AN-1, RS.AN-4, Req-10.5.1, 10.3.1, SRG-OS-000057-GPOS-00027, SRG-OS-000058-GPOS-00028, SRG-OS-000059-GPOS-00029, SV-228564r606407_rule


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

if LC_ALL=C grep -m 1 -q ^log_group /etc/audit/auditd.conf; then
  GROUP=$(awk -F "=" '/log_group/ {print $2}' /etc/audit/auditd.conf | tr -d ' ')
  if ! [ "${GROUP}" == 'root' ] ; then
    chown root:${GROUP} /var/log/audit
    chown root:${GROUP} /var/log/audit/audit.log*
  else
    chown root:root /var/log/audit
    chown root:root /var/log/audit/audit.log*
  fi
else
  chown root:root /var/log/audit
  chown root:root /var/log/audit/audit.log*
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   System Audit Logs Must Have Mode 0640 or Less Permissive   [ref]

Determine where the audit logs are stored with the following command:
$ sudo grep -iw log_file /etc/audit/auditd.conf
log_file = /var/log/audit/audit.log
Configure the audit log to be protected from unauthorized read access by setting the correct permissive mode with the following command:
$ sudo chmod 0600 audit_log_file
By default, audit_log_file is "/var/log/audit/audit.log".
Rationale:
If users can write to audit logs, audit trails can be modified or destroyed.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_var_log_audit
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 19, 3, 4, 5, 6, 7, 8, 5.4.1.1, APO01.06, APO11.04, APO12.06, BAI03.05, BAI08.02, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS05.04, DSS05.07, DSS06.02, MEA02.01, 3.3.1, CCI-000162, CCI-000163, CCI-000164, CCI-001314, 4.2.3.10, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.7.3, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 5.2, SR 6.1, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.16.1.4, A.16.1.5, A.16.1.7, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), AU-9(4), DE.AE-3, DE.AE-5, PR.AC-4, PR.DS-5, PR.PT-1, RS.AN-1, RS.AN-4, Req-10.5, 10.3.1, SRG-OS-000057-GPOS-00027, SRG-OS-000058-GPOS-00028, SRG-OS-000059-GPOS-00029, SRG-OS-000206-GPOS-00084, SV-228564r606407_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Get audit log files
  command: grep -iw ^log_file /etc/audit/auditd.conf
  failed_when: false
  register: log_file_exists
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Parse log file line
  command: awk -F '=' '/^log_file/ {print $2}' /etc/audit/auditd.conf
  register: log_file_line
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - (log_file_exists.stdout | length > 0)
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set default log_file if not set
  set_fact:
    log_file: /var/log/audit/audit.log
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - (log_file_exists is undefined) or (log_file_exists.stdout | length == 0)
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Set log_file from log_file_line if not set already
  set_fact:
    log_file: '{{ log_file_line.stdout | trim }}'
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - (log_file_line.stdout is defined) and (log_file_line.stdout | length > 0)
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Apply mode to log file
  file:
    path: '{{ log_file }}'
    mode: 384
  failed_when: false
  when:
  - '"audit" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-910055
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-6(1)
  - NIST-800-53-AU-9(4)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5
  - PCI-DSSv4-10.3.1
  - file_permissions_var_log_audit
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && rpm --quiet -q audit; then

if LC_ALL=C grep -iw ^log_file /etc/audit/auditd.conf; then
    FILE=$(awk -F "=" '/^log_file/ {print $2}' /etc/audit/auditd.conf | tr -d ' ')
else
    FILE="/var/log/audit/audit.log"
fi


chmod 0600 $FILE

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable auditd Service   [ref]

The auditd service is an essential userspace component of the Linux Auditing System, as it is responsible for writing audit records to disk. The auditd service can be enabled with the following command:
$ sudo systemctl enable auditd.service
Rationale:
Without establishing what type of events occurred, it would be difficult to establish, correlate, and investigate the events leading up to an outage or attack. Ensuring the auditd service is active ensures audit records generated by the kernel are appropriately recorded.

Additionally, a properly configured audit subsystem ensures that actions of individual system users can be uniquely traced to those users so they can be held accountable for their actions.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_auditd_enabled
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.3.1, 3.3.2, 3.3.6, CCI-000126, CCI-000130, CCI-000131, CCI-000132, CCI-000133, CCI-000134, CCI-000135, CCI-000154, CCI-000158, CCI-000172, CCI-000366, CCI-001464, CCI-001487, CCI-001814, CCI-001875, CCI-001876, CCI-001877, CCI-002884, CCI-001878, CCI-001879, CCI-001880, CCI-001881, CCI-001882, CCI-001889, CCI-001914, CCI-000169, 164.308(a)(1)(ii)(D), 164.308(a)(5)(ii)(C), 164.310(a)(2)(iv), 164.310(d)(2)(iii), 164.312(b), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, CIP-004-6 R3.3, CIP-007-3 R6.5, AC-2(g), AU-3, AU-10, AU-2(d), AU-12(c), AU-14(1), AC-6(9), CM-6(a), SI-4(23), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1, Req-10.1, 10.2.1, SRG-OS-000062-GPOS-00031, SRG-OS-000037-GPOS-00015, SRG-OS-000038-GPOS-00016, SRG-OS-000039-GPOS-00017, SRG-OS-000040-GPOS-00018, SRG-OS-000041-GPOS-00019, SRG-OS-000042-GPOS-00021, SRG-OS-000051-GPOS-00024, SRG-OS-000054-GPOS-00025, SRG-OS-000122-GPOS-00063, SRG-OS-000254-GPOS-00095, SRG-OS-000255-GPOS-00096, SRG-OS-000337-GPOS-00129, SRG-OS-000348-GPOS-00136, SRG-OS-000349-GPOS-00137, SRG-OS-000350-GPOS-00138, SRG-OS-000351-GPOS-00139, SRG-OS-000352-GPOS-00140, SRG-OS-000353-GPOS-00141, SRG-OS-000354-GPOS-00142, SRG-OS-000358-GPOS-00145, SRG-OS-000365-GPOS-00152, SRG-OS-000392-GPOS-00172, SRG-OS-000475-GPOS-00220, 4.1.1.2, SV-204503r603261_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    systemd:
      units:
      - name: auditd.service
        enabled: true


[customizations.services]
enabled = ["auditd"]

Complexity:low
Disruption:low
Strategy:enable
include enable_auditd

class enable_auditd {
  service {'auditd':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030000
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.2
  - NIST-800-171-3.3.6
  - NIST-800-53-AC-2(g)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-14(1)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-4(23)
  - PCI-DSS-Req-10.1
  - PCI-DSSv4-10.2.1
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_auditd_enabled

- name: Enable service auditd
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Enable service auditd
    systemd:
      name: auditd
      enabled: 'yes'
      state: started
      masked: 'no'
    when:
    - '"audit" in ansible_facts.packages'
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"audit" in ansible_facts.packages'
  tags:
  - CJIS-5.4.1.1
  - DISA-STIG-RHEL-07-030000
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.2
  - NIST-800-171-3.3.6
  - NIST-800-53-AC-2(g)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-14(1)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-4(23)
  - PCI-DSS-Req-10.1
  - PCI-DSSv4-10.2.1
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_auditd_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { rpm --quiet -q audit; }; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'auditd.service'
"$SYSTEMCTL_EXEC" start 'auditd.service'
"$SYSTEMCTL_EXEC" enable 'auditd.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable Auditing for Processes Which Start Prior to the Audit Daemon   [ref]

To ensure all processes can be audited, even those which start prior to the audit daemon, add the argument audit=1 to the default GRUB 2 command line for the Linux operating system. To ensure that audit=1 is added as a kernel command line argument to newly installed kernels, add audit=1 to the default Grub2 command line for Linux operating systems. Modify the line within /etc/default/grub as shown below:
GRUB_CMDLINE_LINUX="... audit=1 ..."
Run the following command to update command line for already installed kernels:
# grubby --update-kernel=ALL --args="audit=1"
Rationale:
Each process on the system carries an "auditable" flag which indicates whether its activities can be audited. Although auditd takes care of enabling this for all processes which launch after it does, adding the kernel argument ensures it is set for every process during boot.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_grub2_audit_argument
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 19, 3, 4, 5, 6, 7, 8, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS05.02, DSS05.03, DSS05.04, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.3.1, CCI-001464, CCI-000130, CCI-000135, CCI-000169, CCI-000172, CCI-002884, 164.308(a)(1)(ii)(D), 164.308(a)(5)(ii)(C), 164.310(a)(2)(iv), 164.310(d)(2)(iii), 164.312(b), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, AC-17(1), AU-14(1), AU-10, CM-6(a), IR-5(1), DE.AE-3, DE.AE-5, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1, Req-10.3, 10.7, SRG-OS-000037-GPOS-00015, SRG-OS-000042-GPOS-00020, SRG-OS-000062-GPOS-00031, SRG-OS-000392-GPOS-00172, SRG-OS-000462-GPOS-00206, SRG-OS-000471-GPOS-00215, SRG-OS-000473-GPOS-00218, SRG-OS-000254-GPOS-00095, 4.1.1.3


[customizations.kernel]
append = "audit=1"

Complexity:medium
Disruption:low
Reboot:true
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-17(1)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-14(1)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IR-5(1)
  - PCI-DSS-Req-10.3
  - PCI-DSSv4-10.7
  - grub2_audit_argument
  - low_disruption
  - low_severity
  - medium_complexity
  - reboot_required
  - restrict_strategy

- name: Check audit argument exists
  command: grep 'GRUB_CMDLINE_LINUX.*audit=' /etc/default/grub
  failed_when: false
  register: argcheck
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-17(1)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-14(1)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IR-5(1)
  - PCI-DSS-Req-10.3
  - PCI-DSSv4-10.7
  - grub2_audit_argument
  - low_disruption
  - low_severity
  - medium_complexity
  - reboot_required
  - restrict_strategy

- name: Replace existing audit argument
  replace:
    path: /etc/default/grub
    regexp: audit=\w+
    replace: audit=1
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  - argcheck.rc == 0
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-17(1)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-14(1)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IR-5(1)
  - PCI-DSS-Req-10.3
  - PCI-DSSv4-10.7
  - grub2_audit_argument
  - low_disruption
  - low_severity
  - medium_complexity
  - reboot_required
  - restrict_strategy

- name: Add audit argument
  replace:
    path: /etc/default/grub
    regexp: (GRUB_CMDLINE_LINUX=.*)"
    replace: \1 audit=1"
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  - argcheck.rc != 0
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-17(1)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-14(1)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IR-5(1)
  - PCI-DSS-Req-10.3
  - PCI-DSSv4-10.7
  - grub2_audit_argument
  - low_disruption
  - low_severity
  - medium_complexity
  - reboot_required
  - restrict_strategy

- name: Update grub defaults and the bootloader menu
  command: /sbin/grubby --update-kernel=ALL --args="audit=1"
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-53-AC-17(1)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-14(1)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IR-5(1)
  - PCI-DSS-Req-10.3
  - PCI-DSSv4-10.7
  - grub2_audit_argument
  - low_disruption
  - low_severity
  - medium_complexity
  - reboot_required
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { rpm --quiet -q grub2-common; }; then

# Correct the form of default kernel command line in GRUB
if grep -q '^GRUB_CMDLINE_LINUX=.*audit=.*"'  '/etc/default/grub' ; then
       # modify the GRUB command-line if an audit= arg already exists
       sed -i "s/\(^GRUB_CMDLINE_LINUX=\".*\)audit=[^[:space:]]\+\(.*\"\)/\1audit=1\2/"  '/etc/default/grub'
else
       # no audit=arg is present, append it
       sed -i "s/\(^GRUB_CMDLINE_LINUX=\".*\)\"/\1 audit=1\"/"  '/etc/default/grub'
fi
grubby --update-kernel=ALL --args=audit=1

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   GRUB2 bootloader configuration   Group contains 2 groups and 2 rules
[ref]   During the boot process, the boot loader is responsible for starting the execution of the kernel and passing options to it. The boot loader allows for the selection of different kernels - possibly on different partitions or media. The default Red Hat Enterprise Linux 7 boot loader for x86 systems is called GRUB2. Options it can pass to the kernel include single-user mode, which provides root access without any authentication, and the ability to disable SELinux. To prevent local users from modifying the boot parameters and endangering security, protect the boot loader configuration with a password and ensure its configuration file's permissions are set properly.
Group   Non-UEFI GRUB2 bootloader configuration   Group contains 1 rule
[ref]   Non-UEFI GRUB2 bootloader configuration

Rule   Set Boot Loader Password in grub2   [ref]

The grub2 boot loader should have a superuser account and password protection enabled to protect boot-time settings.

Since plaintext passwords are a security risk, generate a hash for the password by running the following command:
# grub2-setpassword
When prompted, enter the password that was selected.

Warning:  To prevent hard-coded passwords, automatic remediation of this control is not available. Remediation must be automated as a component of machine provisioning, or followed manually as outlined above. Also, do NOT manually add the superuser account and password to the grub.cfg file as the grub2-mkconfig command overwrites this file.
Rationale:
Password protection on the boot loader configuration ensures users with physical access cannot trivially alter important bootloader settings. These include which kernel to use, and whether to enter single-user mode.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_grub2_password
Identifiers and References

References:  BP28(R17), 1, 11, 12, 14, 15, 16, 18, 3, 5, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.06, DSS06.10, 3.4.5, CCI-000213, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, A.18.1.4, A.6.1.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CM-6(a), PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.PT-3, FIA_UAU.1, SRG-OS-000080-GPOS-00048, 1.4.1, SV-204438r744095_rule

Group   UEFI GRUB2 bootloader configuration   Group contains 1 rule
[ref]   UEFI GRUB2 bootloader configuration

Rule   Set the UEFI Boot Loader Password   [ref]

The grub2 boot loader should have a superuser account and password protection enabled to protect boot-time settings.

Since plaintext passwords are a security risk, generate a hash for the password by running the following command:
# grub2-setpassword
When prompted, enter the password that was selected.

Warning:  To prevent hard-coded passwords, automatic remediation of this control is not available. Remediation must be automated as a component of machine provisioning, or followed manually as outlined above. Also, do NOT manually add the superuser account and password to the grub.cfg file as the grub2-mkconfig command overwrites this file.
Rationale:
Password protection on the boot loader configuration ensures users with physical access cannot trivially alter important bootloader settings. These include which kernel to use, and whether to enter single-user mode.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_grub2_uefi_password
Identifiers and References

References:  BP28(R17), 11, 12, 14, 15, 16, 18, 3, 5, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.03, DSS06.06, 3.4.5, CCI-000213, 164.308(a)(1)(ii)(B), 164.308(a)(7)(i), 164.308(a)(7)(ii)(A), 164.310(a)(1), 164.310(a)(2)(i), 164.310(a)(2)(ii), 164.310(a)(2)(iii), 164.310(b), 164.310(c), 164.310(d)(1), 164.310(d)(2)(iii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, A.6.1.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CM-6(a), PR.AC-4, PR.AC-6, PR.PT-3, FIA_UAU.1, SRG-OS-000080-GPOS-00048, 1.4.1, SV-204440r744098_rule

Group   Network Configuration and Firewalls   Group contains 2 groups and 2 rules
[ref]   Most systems must be connected to a network of some sort, and this brings with it the substantial risk of network attack. This section discusses the security impact of decisions about networking which must be made when configuring a system.

This section also discusses firewalls, network access controls, and other network security frameworks, which allow system-level rules to be written that can limit an attackers' ability to connect to your system. These rules can specify that network traffic should be allowed or denied from certain IP addresses, hosts, and networks. The rules can also specify which of the system's network services are available to particular hosts or networks.
Group   Wireless Networking   Group contains 1 group and 2 rules
[ref]   Wireless networking, such as 802.11 (WiFi) and Bluetooth, can present a security risk to sensitive or classified systems and networks. Wireless networking hardware is much more likely to be included in laptop or portable systems than in desktops or servers.

Removal of hardware provides the greatest assurance that the wireless capability remains disabled. Acquisition policies often include provisions to prevent the purchase of equipment that will be used in sensitive spaces and includes wireless capabilities. If it is impractical to remove the wireless hardware, and policy permits the device to enter sensitive spaces as long as wireless is disabled, efforts should instead focus on disabling wireless capability via software.
Group   Disable Wireless Through Software Configuration   Group contains 2 rules
[ref]   If it is impossible to remove the wireless hardware from the device in question, disable as much of it as possible through software. The following methods can disable software support for wireless networking, but note that these methods do not prevent malicious software or careless users from re-activating the devices.

Rule   Disable Bluetooth Service   [ref]

The bluetooth service can be disabled with the following command:
$ sudo systemctl mask --now bluetooth.service
$ sudo service bluetooth stop
Rationale:
Disabling the bluetooth service prevents the system from attempting connections to Bluetooth devices, which entails some security risk. Nevertheless, variation in this risk decision may be expected due to the utility of Bluetooth connectivity and its limited range.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_bluetooth_disabled
Identifiers and References

References:  11, 12, 14, 15, 3, 8, 9, APO13.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.05, DSS06.06, 3.1.16, CCI-000085, CCI-001551, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.2.1, A.6.2.2, A.9.1.2, AC-18(a), AC-18(3), CM-7(a), CM-7(b), CM-6(a), MP-7, PR.AC-3, PR.IP-1, PR.PT-3, PR.PT-4


Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    systemd:
      units:
      - name: bluetooth.service
        enabled: false
        mask: true
      - name: bluetooth.socket
        enabled: false
        mask: true


[customizations.services]
disabled = ["bluetooth"]

Complexity:low
Disruption:low
Strategy:enable
include disable_bluetooth

class disable_bluetooth {
  service {'bluetooth':
    enable => false,
    ensure => 'stopped',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Block Disable service bluetooth
  block:

  - name: Disable service bluetooth
    block:

    - name: Disable service bluetooth
      systemd:
        name: bluetooth.service
        enabled: 'no'
        state: stopped
        masked: 'yes'
    rescue:

    - name: Intentionally ignored previous 'Disable service bluetooth' failure, service
        was already disabled
      meta: noop
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.16
  - NIST-800-53-AC-18(3)
  - NIST-800-53-AC-18(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_bluetooth_disabled

- name: Unit Socket Exists - bluetooth.socket
  command: systemctl list-unit-files bluetooth.socket
  register: socket_file_exists
  changed_when: false
  failed_when: socket_file_exists.rc not in [0, 1]
  check_mode: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.16
  - NIST-800-53-AC-18(3)
  - NIST-800-53-AC-18(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_bluetooth_disabled

- name: Disable socket bluetooth
  systemd:
    name: bluetooth.socket
    enabled: 'no'
    state: stopped
    masked: 'yes'
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"bluetooth.socket" in socket_file_exists.stdout_lines[1]'
  tags:
  - NIST-800-171-3.1.16
  - NIST-800-53-AC-18(3)
  - NIST-800-53-AC-18(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_bluetooth_disabled

Complexity:low
Disruption:low
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" stop 'bluetooth.service'
"$SYSTEMCTL_EXEC" disable 'bluetooth.service'
"$SYSTEMCTL_EXEC" mask 'bluetooth.service'
# Disable socket activation if we have a unit file for it
if "$SYSTEMCTL_EXEC" -q list-unit-files bluetooth.socket; then
    "$SYSTEMCTL_EXEC" stop 'bluetooth.socket'
    "$SYSTEMCTL_EXEC" mask 'bluetooth.socket'
fi
# The service may not be running because it has been started and failed,
# so let's reset the state so OVAL checks pass.
# Service should be 'inactive', not 'failed' after reboot though.
"$SYSTEMCTL_EXEC" reset-failed 'bluetooth.service' || true

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable Bluetooth Kernel Module   [ref]

The kernel's module loading system can be configured to prevent loading of the Bluetooth module. Add the following to the appropriate /etc/modprobe.d configuration file to prevent the loading of the Bluetooth module:
install bluetooth /bin/true
Rationale:
If Bluetooth functionality must be disabled, preventing the kernel from loading the kernel module provides an additional safeguard against its activation.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_kernel_module_bluetooth_disabled
Identifiers and References

References:  11, 12, 14, 15, 3, 8, 9, 5.13.1.3, APO13.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.05, DSS06.06, 3.1.16, CCI-000085, CCI-001443, CCI-001444, CCI-001551, CCI-002418, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.2.1, A.6.2.2, A.9.1.2, AC-18(a), AC-18(3), CM-7(a), CM-7(b), CM-6(a), MP-7, PR.AC-3, PR.IP-1, PR.PT-3, PR.PT-4, SRG-OS-000095-GPOS-00049, SRG-OS-000300-GPOS-00118


Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,install%20bluetooth%20/bin/true%0Ablacklist%20bluetooth%0A
        mode: 0644
        path: /etc/modprobe.d/bluetooth.conf
        overwrite: true

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: Ensure kernel module 'bluetooth' is disabled
  lineinfile:
    create: true
    dest: /etc/modprobe.d/bluetooth.conf
    regexp: install\s+bluetooth
    line: install bluetooth /bin/true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.13.1.3
  - NIST-800-171-3.1.16
  - NIST-800-53-AC-18(3)
  - NIST-800-53-AC-18(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - kernel_module_bluetooth_disabled
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required

- name: Ensure kernel module 'bluetooth' is blacklisted
  lineinfile:
    create: true
    dest: /etc/modprobe.d/bluetooth.conf
    regexp: ^blacklist bluetooth$
    line: blacklist bluetooth
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.13.1.3
  - NIST-800-171-3.1.16
  - NIST-800-53-AC-18(3)
  - NIST-800-53-AC-18(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - kernel_module_bluetooth_disabled
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if LC_ALL=C grep -q -m 1 "^install bluetooth" /etc/modprobe.d/bluetooth.conf ; then
	
	sed -i 's#^install bluetooth.*#install bluetooth /bin/true#g' /etc/modprobe.d/bluetooth.conf
else
	echo -e "\n# Disable per security requirements" >> /etc/modprobe.d/bluetooth.conf
	echo "install bluetooth /bin/true" >> /etc/modprobe.d/bluetooth.conf
fi

if ! LC_ALL=C grep -q -m 1 "^blacklist bluetooth$" /etc/modprobe.d/bluetooth.conf ; then
	echo "blacklist bluetooth" >> /etc/modprobe.d/bluetooth.conf
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   File Permissions and Masks   Group contains 3 groups and 4 rules
[ref]   Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access.

Several of the commands in this section search filesystems for files or directories with certain characteristics, and are intended to be run on every local partition on a given system. When the variable PART appears in one of the commands below, it means that the command is intended to be run repeatedly, with the name of each local partition substituted for PART in turn.

The following command prints a list of all xfs partitions on the local system, which is the default filesystem for Red Hat Enterprise Linux 7 installations:
$ mount -t xfs | awk '{print $3}'
For any systems that use a different local filesystem type, modify this command as appropriate.
Group   Restrict Dynamic Mounting and Unmounting of Filesystems   Group contains 1 rule
[ref]   Linux includes a number of facilities for the automated addition and removal of filesystems on a running system. These facilities may be necessary in many environments, but this capability also carries some risk -- whether direct risk from allowing users to introduce arbitrary filesystems, or risk that software flaws in the automated mount facility itself could allow an attacker to compromise the system.

This command can be used to list the types of filesystems that are available to the currently executing kernel:
$ find /lib/modules/`uname -r`/kernel/fs -type f -name '*.ko'
If these filesystems are not required then they can be explicitly disabled in a configuratio file in /etc/modprobe.d.

Rule   Disable Modprobe Loading of USB Storage Driver   [ref]

To prevent USB storage devices from being used, configure the kernel module loading system to prevent automatic loading of the USB storage driver. To configure the system to prevent the usb-storage kernel module from being loaded, add the following line to the file /etc/modprobe.d/usb-storage.conf:
install usb-storage /bin/true
To configure the system to prevent the usb-storage from being used, add the following line to file /etc/modprobe.d/usb-storage.conf:
blacklist usb-storage
This will prevent the modprobe program from loading the usb-storage module, but will not prevent an administrator (or another program) from using the insmod program to load the module manually.
Rationale:
USB storage devices such as thumb drives can be used to introduce malicious software.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_kernel_module_usb-storage_disabled
Identifiers and References

References:  1, 12, 15, 16, 5, APO13.01, DSS01.04, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.21, CCI-000366, CCI-000778, CCI-001958, 164.308(a)(3)(i), 164.308(a)(3)(ii)(A), 164.310(d)(1), 164.310(d)(2), 164.312(a)(1), 164.312(a)(2)(iv), 164.312(b), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.6, A.11.2.6, A.13.1.1, A.13.2.1, A.18.1.4, A.6.2.1, A.6.2.2, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, CM-7(a), CM-7(b), CM-6(a), MP-7, PR.AC-1, PR.AC-3, PR.AC-6, PR.AC-7, SRG-OS-000114-GPOS-00059, SRG-OS-000378-GPOS-00163, SRG-OS-000480-GPOS-00227, 1.1.24, SV-204449r853891_rule


Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,install%20usb-storage%20/bin/true%0Ablacklist%20usb-storage%0A
        mode: 0644
        path: /etc/modprobe.d/usb-storage.conf
        overwrite: true

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: Ensure kernel module 'usb-storage' is disabled
  lineinfile:
    create: true
    dest: /etc/modprobe.d/usb-storage.conf
    regexp: install\s+usb-storage
    line: install usb-storage /bin/true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-020100
  - NIST-800-171-3.1.21
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - kernel_module_usb-storage_disabled
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required

- name: Ensure kernel module 'usb-storage' is blacklisted
  lineinfile:
    create: true
    dest: /etc/modprobe.d/usb-storage.conf
    regexp: ^blacklist usb-storage$
    line: blacklist usb-storage
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-020100
  - NIST-800-171-3.1.21
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - NIST-800-53-MP-7
  - disable_strategy
  - kernel_module_usb-storage_disabled
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if LC_ALL=C grep -q -m 1 "^install usb-storage" /etc/modprobe.d/usb-storage.conf ; then
	
	sed -i 's#^install usb-storage.*#install usb-storage /bin/true#g' /etc/modprobe.d/usb-storage.conf
else
	echo -e "\n# Disable per security requirements" >> /etc/modprobe.d/usb-storage.conf
	echo "install usb-storage /bin/true" >> /etc/modprobe.d/usb-storage.conf
fi

if ! LC_ALL=C grep -q -m 1 "^blacklist usb-storage$" /etc/modprobe.d/usb-storage.conf ; then
	echo "blacklist usb-storage" >> /etc/modprobe.d/usb-storage.conf
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Restrict Programs from Dangerous Execution Patterns   Group contains 1 group and 3 rules
[ref]   The recommendations in this section are designed to ensure that the system's features to protect against potentially dangerous program execution are activated. These protections are applied at the system initialization or kernel level, and defend against certain types of badly-configured or compromised programs.
Group   Enable ExecShield   Group contains 3 rules
[ref]   ExecShield describes kernel features that provide protection against exploitation of memory corruption errors such as buffer overflows. These features include random placement of the stack and other memory regions, prevention of execution in memory that should only hold data, and special handling of text buffers. These protections are enabled by default on 32-bit systems and controlled through sysctl variables kernel.exec-shield and kernel.randomize_va_space. On the latest 64-bit systems, kernel.exec-shield cannot be enabled or disabled with sysctl.

Rule   Enable ExecShield via sysctl   [ref]

By default on Red Hat Enterprise Linux 7 64-bit systems, ExecShield is enabled and can only be disabled if the hardware does not support ExecShield or is disabled in /etc/default/grub.
Rationale:
ExecShield uses the segmentation feature on all x86 systems to prevent execution in memory higher than a certain address. It writes an address as a limit in the code segment descriptor, to control where code can be executed, on a per-process basis. When the kernel places a process's memory regions such as the stack and heap higher than this address, the hardware prevents execution in that address range. This is enabled by default on the latest Red Hat and Fedora systems if supported by the hardware.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sysctl_kernel_exec_shield
Identifiers and References

References:  12, 15, 8, APO13.01, DSS05.02, 3.1.7, CCI-002530, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.13.1.1, A.13.2.1, A.14.1.3, SC-39, CM-6(a), PR.PT-4, SRG-OS-000433-GPOS-00192, 1.5.2


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: Check noexec argument exists
  command: grep '^GRUB_CMDLINE_LINUX=.*noexec=.*"' /etc/default/grub
  failed_when: false
  register: argcheck
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-39
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy
  - sysctl_kernel_exec_shield

- name: Replace existing noexec argument
  replace:
    path: /etc/default/grub
    regexp: \(^GRUB_CMDLINE_LINUX=".*\)noexec=?[^[:space:]]*\(.*"\)
    replace: \1 \2
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - argcheck.rc == 0
  tags:
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-39
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy
  - sysctl_kernel_exec_shield

- name: Update grub defaults and the bootloader menu
  command: /sbin/grubby --update-kernel=ALL --remove-args="noexec"
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-39
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy
  - sysctl_kernel_exec_shield

Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Correct the form of default kernel command line in GRUB
if grep -q '^GRUB_CMDLINE_LINUX=.*noexec=.*"'  '/etc/default/grub' ; then
       sed -i 's/\(^GRUB_CMDLINE_LINUX=".*\)noexec=?[^[:space:]]*\(.*"\)/\1 \2/' '/etc/default/grub'
fi
grubby --update-kernel=ALL --remove-args=noexec

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Restrict Exposed Kernel Pointer Addresses Access   [ref]

To set the runtime status of the kernel.kptr_restrict kernel parameter, run the following command:
$ sudo sysctl -w kernel.kptr_restrict=1
To make sure that the setting is persistent, add the following line to a file in the directory /etc/sysctl.d:
kernel.kptr_restrict = 1
Rationale:
Exposing kernel pointers (through procfs or seq_printf()) exposes kernel writeable structures which may contain functions pointers. If a write vulnerability occurs in the kernel, allowing write access to any of this structure, the kernel can be compromised. This option disallow any program without the CAP_SYSLOG capability to get the addresses of kernel pointers by replacing them with 0.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sysctl_kernel_kptr_restrict
Identifiers and References

References:  BP28(R23), CCI-002824, CCI-000366, CIP-002-5 R1.1, CIP-002-5 R1.2, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 4.1, CIP-004-6 4.2, CIP-004-6 R2.2.3, CIP-004-6 R2.2.4, CIP-004-6 R2.3, CIP-004-6 R4, CIP-005-6 R1, CIP-005-6 R1.1, CIP-005-6 R1.2, CIP-007-3 R3, CIP-007-3 R3.1, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, CIP-007-3 R8.4, CIP-009-6 R.1.1, CIP-009-6 R4, SC-30, SC-30(2), SC-30(5), CM-6(a), SRG-OS-000132-GPOS-00067, SRG-OS-000433-GPOS-00192, SRG-OS-000480-GPOS-00227


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,kernel.kptr_restrict%3D1%0A
        mode: 0644
        path: /etc/sysctl.d/75-sysctl_kernel_kptr_restrict.conf
        overwrite: true

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: List /etc/sysctl.d/*.conf files
  find:
    paths:
    - /etc/sysctl.d/
    - /run/sysctl.d/
    - /usr/local/lib/sysctl.d/
    contains: ^[\s]*kernel.kptr_restrict.*$
    patterns: '*.conf'
    file_type: any
  register: find_sysctl_d
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - NIST-800-53-SC-30(5)
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_kptr_restrict

- name: Comment out any occurrences of kernel.kptr_restrict from config files
  replace:
    path: '{{ item.path }}'
    regexp: ^[\s]*kernel.kptr_restrict
    replace: '#kernel.kptr_restrict'
  loop: '{{ find_sysctl_d.files }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - NIST-800-53-SC-30(5)
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_kptr_restrict
- name: XCCDF Value sysctl_kernel_kptr_restrict_value # promote to variable
  set_fact:
    sysctl_kernel_kptr_restrict_value: !!str 1
  tags:
    - always

- name: Ensure sysctl kernel.kptr_restrict is set
  sysctl:
    name: kernel.kptr_restrict
    value: '{{ sysctl_kernel_kptr_restrict_value }}'
    sysctl_file: /etc/sysctl.conf
    state: present
    reload: true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - NIST-800-53-SC-30(5)
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_kptr_restrict

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Comment out any occurrences of kernel.kptr_restrict from /etc/sysctl.d/*.conf files

for f in /etc/sysctl.d/*.conf /run/sysctl.d/*.conf /usr/local/lib/sysctl.d/*.conf; do

  matching_list=$(grep -P '^(?!#).*[\s]*kernel.kptr_restrict.*$' $f | uniq )
  if ! test -z "$matching_list"; then
    while IFS= read -r entry; do
      escaped_entry=$(sed -e 's|/|\\/|g' <<< "$entry")
      # comment out "kernel.kptr_restrict" matches to preserve user data
      sed -i "s/^${escaped_entry}$/# &/g" $f
    done <<< "$matching_list"
  fi
done

#
# Set sysctl config file which to save the desired value
#

SYSCONFIG_FILE="/etc/sysctl.conf"

sysctl_kernel_kptr_restrict_value='1'


#
# Set runtime for kernel.kptr_restrict
#
/sbin/sysctl -q -n -w kernel.kptr_restrict="$sysctl_kernel_kptr_restrict_value"

#
# If kernel.kptr_restrict present in /etc/sysctl.conf, change value to appropriate value
#	else, add "kernel.kptr_restrict = value" to /etc/sysctl.conf
#

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^kernel.kptr_restrict")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$sysctl_kernel_kptr_restrict_value"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^kernel.kptr_restrict\\>" "${SYSCONFIG_FILE}"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^kernel.kptr_restrict\\>.*/$escaped_formatted_output/gi" "${SYSCONFIG_FILE}"
else
    if [[ -s "${SYSCONFIG_FILE}" ]] && [[ -n "$(tail -c 1 -- "${SYSCONFIG_FILE}" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "${SYSCONFIG_FILE}"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "${SYSCONFIG_FILE}" >> "${SYSCONFIG_FILE}"
    printf '%s\n' "$formatted_output" >> "${SYSCONFIG_FILE}"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable Randomized Layout of Virtual Address Space   [ref]

To set the runtime status of the kernel.randomize_va_space kernel parameter, run the following command:
$ sudo sysctl -w kernel.randomize_va_space=2
To make sure that the setting is persistent, add the following line to a file in the directory /etc/sysctl.d:
kernel.randomize_va_space = 2
Rationale:
Address space layout randomization (ASLR) makes it more difficult for an attacker to predict the location of attack code they have introduced into a process's address space during an attempt at exploitation. Additionally, ASLR makes it more difficult for an attacker to know the location of existing code in order to re-purpose it using return oriented programming (ROP) techniques.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sysctl_kernel_randomize_va_space
Identifiers and References

References:  BP28(R23), 3.1.7, CCI-000366, CCI-002824, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), CIP-002-5 R1.1, CIP-002-5 R1.2, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 4.1, CIP-004-6 4.2, CIP-004-6 R2.2.3, CIP-004-6 R2.2.4, CIP-004-6 R2.3, CIP-004-6 R4, CIP-005-6 R1, CIP-005-6 R1.1, CIP-005-6 R1.2, CIP-007-3 R3, CIP-007-3 R3.1, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, CIP-007-3 R8.4, CIP-009-6 R.1.1, CIP-009-6 R4, SC-30, SC-30(2), CM-6(a), Req-2.2.1, 2.2.3, SRG-OS-000433-GPOS-00193, SRG-OS-000480-GPOS-00227, 1.5.3, SV-204584r880794_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,kernel.randomize_va_space%3D2%0A
        mode: 0644
        path: /etc/sysctl.d/75-sysctl_kernel_randomize_va_space.conf
        overwrite: true

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: List /etc/sysctl.d/*.conf files
  find:
    paths:
    - /etc/sysctl.d/
    - /run/sysctl.d/
    - /usr/local/lib/sysctl.d/
    contains: ^[\s]*kernel.randomize_va_space.*$
    patterns: '*.conf'
    file_type: any
  register: find_sysctl_d
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040201
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

- name: Comment out any occurrences of kernel.randomize_va_space from config files
  replace:
    path: '{{ item.path }}'
    regexp: ^[\s]*kernel.randomize_va_space
    replace: '#kernel.randomize_va_space'
  loop: '{{ find_sysctl_d.files }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040201
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

- name: Ensure sysctl kernel.randomize_va_space is set to 2
  sysctl:
    name: kernel.randomize_va_space
    value: '2'
    sysctl_file: /etc/sysctl.conf
    state: present
    reload: true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040201
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Comment out any occurrences of kernel.randomize_va_space from /etc/sysctl.d/*.conf files

for f in /etc/sysctl.d/*.conf /run/sysctl.d/*.conf /usr/local/lib/sysctl.d/*.conf; do

  matching_list=$(grep -P '^(?!#).*[\s]*kernel.randomize_va_space.*$' $f | uniq )
  if ! test -z "$matching_list"; then
    while IFS= read -r entry; do
      escaped_entry=$(sed -e 's|/|\\/|g' <<< "$entry")
      # comment out "kernel.randomize_va_space" matches to preserve user data
      sed -i "s/^${escaped_entry}$/# &/g" $f
    done <<< "$matching_list"
  fi
done

#
# Set sysctl config file which to save the desired value
#

SYSCONFIG_FILE="/etc/sysctl.conf"


#
# Set runtime for kernel.randomize_va_space
#
/sbin/sysctl -q -n -w kernel.randomize_va_space="2"

#
# If kernel.randomize_va_space present in /etc/sysctl.conf, change value to "2"
#	else, add "kernel.randomize_va_space = 2" to /etc/sysctl.conf
#

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^kernel.randomize_va_space")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "2"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^kernel.randomize_va_space\\>" "${SYSCONFIG_FILE}"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^kernel.randomize_va_space\\>.*/$escaped_formatted_output/gi" "${SYSCONFIG_FILE}"
else
    if [[ -s "${SYSCONFIG_FILE}" ]] && [[ -n "$(tail -c 1 -- "${SYSCONFIG_FILE}" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "${SYSCONFIG_FILE}"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "${SYSCONFIG_FILE}" >> "${SYSCONFIG_FILE}"
    printf '%s\n' "$formatted_output" >> "${SYSCONFIG_FILE}"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   SELinux   Group contains 1 group and 5 rules
[ref]   SELinux is a feature of the Linux kernel which can be used to guard against misconfigured or compromised programs. SELinux enforces the idea that programs should be limited in what files they can access and what actions they can take.

The default SELinux policy, as configured on Red Hat Enterprise Linux 7, has been sufficiently developed and debugged that it should be usable on almost any system with minimal configuration and a small amount of system administrator training. This policy prevents system services - including most of the common network-visible services such as mail servers, FTP servers, and DNS servers - from accessing files which those services have no valid reason to access. This action alone prevents a huge amount of possible damage from network attacks against services, from trojaned software, and so forth.

This guide recommends that SELinux be enabled using the default (targeted) policy on every Red Hat Enterprise Linux 7 system, unless that system has unusual requirements which make a stronger policy appropriate.

For more information on SELinux, see https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/7/html/selinux_users_and_administrators_guide.
Group   SELinux - Booleans   Group contains 1 rule
[ref]   Enable or Disable runtime customization of SELinux system policies without having to reload or recompile the SELinux policy.

Rule   Enable the fips_mode SELinux Boolean   [ref]

By default, the SELinux boolean fips_mode is enabled. This allows all SELinux domains to execute in fips_mode. If this setting is disabled, it should be enabled. To enable the fips_mode SELinux boolean, run the following command:
$ sudo setsebool -P fips_mode on
Rationale:
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sebool_fips_mode
Identifiers and References

References:  13, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.13.11, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, SC-12(2), SC-12(3), IA-7, SC-13, CM-6(a), SC-12, PR.DS-5


Complexity:low
Disruption:low
Strategy:enable
- name: XCCDF Value var_fips_mode # promote to variable
  set_fact:
    var_fips_mode: !!str true
  tags:
    - always

- name: Ensure libsemanage-python installed
  package:
    name: libsemanage-python
    state: present
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - not ( lookup("env", "container") == "bwrap-osbuild" )
  tags:
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - sebool_fips_mode

- name: Set SELinux boolean fips_mode accordingly
  seboolean:
    name: fips_mode
    state: '{{ var_fips_mode }}'
    persistent: true
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - not ( lookup("env", "container") == "bwrap-osbuild" )
  tags:
  - NIST-800-171-3.13.11
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-7
  - NIST-800-53-SC-12
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - sebool_fips_mode

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if ! ( [ "${container:-}" == "bwrap-osbuild" ] ) && [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_fips_mode='true'


setsebool -P fips_mode $var_fips_mode

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure SELinux Not Disabled in /etc/default/grub   [ref]

SELinux can be disabled at boot time by an argument in /etc/default/grub. Remove any instances of selinux=0 from the kernel arguments in that file to prevent SELinux from being disabled at boot.
Rationale:
Disabling a major host protection feature, such as SELinux, at boot time prevents it from confining system services at boot time. Further, it increases the chances that it will remain off during system operation.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_grub2_enable_selinux
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 3, 4, 5, 6, 8, 9, APO01.06, APO11.04, APO13.01, BAI03.05, DSS01.05, DSS03.01, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.03, DSS06.06, MEA02.01, 3.1.2, 3.7.2, CCI-000022, CCI-000032, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), 4.2.3.4, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.4, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, 4.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.1.2, A.13.1.3, A.13.2.1, A.13.2.2, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, AC-3, AC-3(3)(a), DE.AE-1, ID.AM-3, PR.AC-4, PR.AC-5, PR.AC-6, PR.DS-5, PR.PT-1, PR.PT-3, PR.PT-4, 1.6.1.2


Complexity:low
Disruption:low
Strategy:restrict
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Find /etc/grub.d/ files
  ansible.builtin.find:
    paths:
    - /etc/grub.d/
    follow: true
  register: result_grub_d
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Ensure SELinux Not Disabled
    in /etc/grub.d/ files
  ansible.builtin.replace:
    dest: '{{ item.path }}'
    regexp: (selinux|enforcing)=0
  with_items:
  - '{{ result_grub_d.files }}'
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Check if /etc/grub2.cfg
    exists
  ansible.builtin.stat:
    path: /etc/grub2.cfg
  register: result_grub2_cfg_present
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Check if /etc/default/grub
    exists
  ansible.builtin.stat:
    path: /etc/default/grub
  register: result_default_grub_present
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Ensure SELinux Not Disabled
    in /etc/grub2.cfg
  ansible.builtin.replace:
    dest: /etc/grub2.cfg
    regexp: (selinux|enforcing)=0
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  - result_grub2_cfg_present.stat.exists
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

- name: Ensure SELinux Not Disabled in /etc/default/grub - Ensure SELinux Not Disabled
    in /etc/default/grub
  ansible.builtin.replace:
    dest: /etc/default/grub
    regexp: (selinux|enforcing)=0
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"grub2-common" in ansible_facts.packages'
  - result_default_grub_present.stat.exists
  tags:
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - grub2_enable_selinux
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { rpm --quiet -q grub2-common; }; then

sed -i --follow-symlinks "s/selinux=0//gI" /etc/default/grub /etc/grub2.cfg /etc/grub.d/*
sed -i --follow-symlinks "s/enforcing=0//gI" /etc/default/grub /etc/grub2.cfg /etc/grub.d/*

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure No Daemons are Unconfined by SELinux   [ref]

Daemons for which the SELinux policy does not contain rules will inherit the context of the parent process. Because daemons are launched during startup and descend from the init process, they inherit the unconfined_service_t context.

To check for unconfined daemons, run the following command:
$ sudo ps -eZ | grep "unconfined_service_t"
It should produce no output in a well-configured system.
Warning:  Automatic remediation of this control is not available. Remediation can be achieved by amending SELinux policy or stopping the unconfined daemons as outlined above.
Rationale:
Daemons which run with the unconfined_service_t context may cause AVC denials, or allow privileges that the daemon does not require.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_selinux_confinement_of_daemons
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 18, 3, 5, 6, 9, APO01.06, APO11.04, BAI03.05, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.06, MEA02.01, 3.1.2, 3.1.5, 3.7.2, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 2.8, SR 2.9, SR 5.2, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.5.1, A.12.6.2, A.12.7.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-7(a), CM-7(b), CM-6(a), AC-3(3)(a), AC-6, PR.AC-4, PR.DS-5, PR.IP-1, PR.PT-1, PR.PT-3, 1.6.1.6

Rule   Configure SELinux Policy   [ref]

The SELinux targeted policy is appropriate for general-purpose desktops and servers, as well as systems in many other roles. To configure the system to use this policy, add or correct the following line in /etc/selinux/config:
SELINUXTYPE=targeted
Other policies, such as mls, provide additional security labeling and greater confinement but are not compatible with many general-purpose use cases.
Rationale:
Setting the SELinux policy to targeted or a more specialized policy ensures the system will confine processes that are likely to be targeted for exploitation, such as network or system services.

Note: During the development or debugging of SELinux modules, it is common to temporarily place non-production systems in permissive mode. In such temporary cases, SELinux policies should be developed, and once work is completed, the system should be reconfigured to targeted.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_selinux_policytype
Identifiers and References

References:  BP28(R66), 1, 11, 12, 13, 14, 15, 16, 18, 3, 4, 5, 6, 8, 9, APO01.06, APO11.04, APO13.01, BAI03.05, DSS01.05, DSS03.01, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.03, DSS06.06, MEA02.01, 3.1.2, 3.7.2, CCI-002165, CCI-002696, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), 4.2.3.4, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.4, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, 4.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.1.2, A.13.1.3, A.13.2.1, A.13.2.2, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.2, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-004-6 R3.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, CIP-007-3 R6.5, AC-3, AC-3(3)(a), AU-9, SC-7(21), DE.AE-1, ID.AM-3, PR.AC-4, PR.AC-5, PR.AC-6, PR.DS-5, PR.PT-1, PR.PT-3, PR.PT-4, SRG-OS-000445-GPOS-00199, 1.6.1.3, SV-204454r853896_rule


Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
- name: XCCDF Value var_selinux_policy_name # promote to variable
  set_fact:
    var_selinux_policy_name: !!str targeted
  tags:
    - always

- name: Configure SELinux Policy
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/selinux/config
      create: false
      regexp: ^SELINUXTYPE=
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/selinux/config
    lineinfile:
      path: /etc/selinux/config
      create: false
      regexp: ^SELINUXTYPE=
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/selinux/config
    lineinfile:
      path: /etc/selinux/config
      create: true
      regexp: ^SELINUXTYPE=
      line: SELINUXTYPE={{ var_selinux_policy_name }}
      state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-020220
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - NIST-800-53-AU-9
  - NIST-800-53-SC-7(21)
  - low_complexity
  - low_disruption
  - medium_severity
  - reboot_required
  - restrict_strategy
  - selinux_policytype

Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_selinux_policy_name='targeted'


if [ -e "/etc/selinux/config" ] ; then
    
    LC_ALL=C sed -i "/^SELINUXTYPE=/Id" "/etc/selinux/config"
else
    touch "/etc/selinux/config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/selinux/config"

cp "/etc/selinux/config" "/etc/selinux/config.bak"
# Insert at the end of the file
printf '%s\n' "SELINUXTYPE=$var_selinux_policy_name" >> "/etc/selinux/config"
# Clean up after ourselves.
rm "/etc/selinux/config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure SELinux State is Enforcing   [ref]

The SELinux state should be set to enforcing at system boot time. In the file /etc/selinux/config, add or correct the following line to configure the system to boot into enforcing mode:
SELINUX=enforcing
Rationale:
Setting the SELinux state to enforcing ensures SELinux is able to confine potentially compromised processes to the security policy, which is designed to prevent them from causing damage to the system or further elevating their privileges.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_selinux_state
Identifiers and References

References:  BP28(R4), BP28(R66), 1, 11, 12, 13, 14, 15, 16, 18, 3, 4, 5, 6, 8, 9, APO01.06, APO11.04, APO13.01, BAI03.05, DSS01.05, DSS03.01, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.03, DSS06.06, MEA02.01, 3.1.2, 3.7.2, CCI-001084, CCI-002165, CCI-002696, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), 4.2.3.4, 4.3.3.2.2, 4.3.3.3.9, 4.3.3.4, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, 4.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.1, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.1.2, A.13.1.3, A.13.2.1, A.13.2.2, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.2, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-004-6 R3.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, CIP-007-3 R6.5, AC-3, AC-3(3)(a), AU-9, SC-7(21), DE.AE-1, ID.AM-3, PR.AC-4, PR.AC-5, PR.AC-6, PR.DS-5, PR.PT-1, PR.PT-3, PR.PT-4, SRG-OS-000445-GPOS-00199, SRG-OS-000134-GPOS-00068, 1.6.1.4, 1.6.1.5, SV-204453r853895_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value var_selinux_state # promote to variable
  set_fact:
    var_selinux_state: !!str enforcing
  tags:
    - always

- name: Ensure SELinux State is Enforcing
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/selinux/config
      create: false
      regexp: ^SELINUX=
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/selinux/config
    lineinfile:
      path: /etc/selinux/config
      create: false
      regexp: ^SELINUX=
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/selinux/config
    lineinfile:
      path: /etc/selinux/config
      create: true
      regexp: ^SELINUX=
      line: SELINUX={{ var_selinux_state }}
      state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-020210
  - NIST-800-171-3.1.2
  - NIST-800-171-3.7.2
  - NIST-800-53-AC-3
  - NIST-800-53-AC-3(3)(a)
  - NIST-800-53-AU-9
  - NIST-800-53-SC-7(21)
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy
  - selinux_state

Complexity:low
Disruption:low
Reboot:true
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_selinux_state='enforcing'


if [ -e "/etc/selinux/config" ] ; then
    
    LC_ALL=C sed -i "/^SELINUX=/Id" "/etc/selinux/config"
else
    touch "/etc/selinux/config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/selinux/config"

cp "/etc/selinux/config" "/etc/selinux/config.bak"
# Insert at the end of the file
printf '%s\n' "SELINUX=$var_selinux_state" >> "/etc/selinux/config"
# Clean up after ourselves.
rm "/etc/selinux/config.bak"

fixfiles onboot
fixfiles -f relabel

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Services   Group contains 3 groups and 21 rules
[ref]   The best protection against vulnerable software is running less software. This section describes how to review the software which Red Hat Enterprise Linux 7 installs on a system and disable software which is not needed. It then enumerates the software packages installed on a default Red Hat Enterprise Linux 7 system and provides guidance about which ones can be safely disabled.

Red Hat Enterprise Linux 7 provides a convenient minimal install option that essentially installs the bare necessities for a functional system. When building Red Hat Enterprise Linux 7 systems, it is highly recommended to select the minimal packages and then build up the system from there.
Group   SSH Server   Group contains 1 group and 20 rules
[ref]   The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between two systems, as well as server authentication, through the use of public key cryptography. The implementation included with the system is called OpenSSH, and more detailed documentation is available from its website, https://www.openssh.com. Its server program is called sshd and provided by the RPM package openssh-server.
Group   Configure OpenSSH Server if Necessary   Group contains 18 rules
[ref]   If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file /etc/ssh/sshd_config. The following recommendations can be applied to this file. See the sshd_config(5) man page for more detailed information.

Rule   Set SSH Client Alive Count Max to zero   [ref]

The SSH server sends at most ClientAliveCountMax messages during a SSH session and waits for a response from the SSH client. The option ClientAliveInterval configures timeout after each ClientAliveCountMax message. If the SSH server does not receive a response from the client, then the connection is considered unresponsive and terminated. To ensure the SSH timeout occurs precisely when the ClientAliveInterval is set, set the ClientAliveCountMax to value of 0 in /etc/ssh/sshd_config:
Rationale:
This ensures a user login will be terminated as soon as the ClientAliveInterval is reached.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_set_keepalive_0
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 18, 3, 5, 7, 8, 5.5.6, APO13.01, BAI03.01, BAI03.02, BAI03.03, DSS01.03, DSS03.05, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.11, CCI-000879, CCI-001133, CCI-002361, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 6.2, A.12.4.1, A.12.4.3, A.14.1.1, A.14.2.1, A.14.2.5, A.18.1.4, A.6.1.2, A.6.1.5, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.3, CIP-007-3 R5.1, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, AC-2(5), AC-12, AC-17(a), SC-10, CM-6(a), DE.CM-1, DE.CM-3, PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.IP-2, Req-8.1.8, 8.2.8, SRG-OS-000126-GPOS-00066, SRG-OS-000163-GPOS-00072, SRG-OS-000279-GPOS-00109, 5.2.12, SV-204589r853992_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Set SSH Client Alive Count Max to zero
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveCountMax\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveCountMax\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*ClientAliveCountMax\s+
      line: ClientAliveCountMax 0
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-040340
  - NIST-800-171-3.1.11
  - NIST-800-53-AC-12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-2(5)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-10
  - PCI-DSS-Req-8.1.8
  - PCI-DSSv4-8.2.8
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_set_keepalive_0

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*ClientAliveCountMax\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "ClientAliveCountMax 0" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "ClientAliveCountMax 0" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set SSH Client Alive Interval   [ref]

SSH allows administrators to set a network responsiveness timeout interval. After this interval has passed, the unresponsive client will be automatically logged out.

To set this timeout interval, edit the following line in /etc/ssh/sshd_config as follows:
ClientAliveInterval 300


The timeout interval is given in seconds. For example, have a timeout of 10 minutes, set interval to 600.

If a shorter timeout has already been set for the login shell, that value will preempt any SSH setting made in /etc/ssh/sshd_config. Keep in mind that some processes may stop SSH from correctly detecting that the user is idle.
Warning:  SSH disconnecting unresponsive clients will not have desired effect without also configuring ClientAliveCountMax in the SSH service configuration.
Warning:  Following conditions may prevent the SSH session to time out:
  • Remote processes on the remote machine generates output. As the output has to be transferred over the network to the client, the timeout is reset every time such transfer happens.
  • Any scp or sftp activity by the same user to the host resets the timeout.
Rationale:
Terminating an idle ssh session within a short time period reduces the window of opportunity for unauthorized personnel to take control of a management session enabled on the console or console port that has been let unattended.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_set_idle_timeout
Identifiers and References

References:  BP28(R29), 1, 12, 13, 14, 15, 16, 18, 3, 5, 7, 8, 5.5.6, APO13.01, BAI03.01, BAI03.02, BAI03.03, DSS01.03, DSS03.05, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.11, CCI-000879, CCI-001133, CCI-002361, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 6.2, A.12.4.1, A.12.4.3, A.14.1.1, A.14.2.1, A.14.2.5, A.18.1.4, A.6.1.2, A.6.1.5, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.3, CIP-007-3 R5.1, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, CM-6(a), AC-17(a), AC-2(5), AC-12, AC-17(a), SC-10, CM-6(a), DE.CM-1, DE.CM-3, PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.IP-2, Req-8.1.8, 8.2.8, SRG-OS-000126-GPOS-00066, SRG-OS-000163-GPOS-00072, SRG-OS-000279-GPOS-00109, SRG-OS-000395-GPOS-00175, 5.3.16, SV-204587r861072_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value sshd_idle_timeout_value # promote to variable
  set_fact:
    sshd_idle_timeout_value: !!str 300
  tags:
    - always

- name: Set SSH Client Alive Interval
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveInterval\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveInterval\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*ClientAliveInterval\s+
      line: ClientAliveInterval {{ sshd_idle_timeout_value }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_distribution == 'RedHat' and ansible_distribution_version is version('8.5',
    '<=')
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-040320
  - NIST-800-171-3.1.11
  - NIST-800-53-AC-12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-2(5)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-10
  - PCI-DSS-Req-8.1.8
  - PCI-DSSv4-8.2.8
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_set_idle_timeout

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { grep -qP "^ID=[\"']?rhel[\"']?$" "/etc/os-release" && { real="$(grep -P "^VERSION_ID=[\"']?[\w.]+[\"']?$" /etc/os-release | sed "s/^VERSION_ID=[\"']\?\([^\"']\+\)[\"']\?$/\1/")"; expected="8.5"; printf "%s\n%s" "$real" "$expected" | sort -VC; }; }; then

sshd_idle_timeout_value='300'


if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*ClientAliveInterval\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "ClientAliveInterval $sshd_idle_timeout_value" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "ClientAliveInterval $sshd_idle_timeout_value" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable Host-Based Authentication   [ref]

SSH's cryptographic host-based authentication is more secure than .rhosts authentication. However, it is not recommended that hosts unilaterally trust one another, even within an organization.
The default SSH configuration disables host-based authentication. The appropriate configuration is used if no value is set for HostbasedAuthentication.
To explicitly disable host-based authentication, add or correct the following line in /etc/ssh/sshd_config:
HostbasedAuthentication no
Rationale:
SSH trust relationships mean a compromise on one host can allow an attacker to move trivially to other hosts.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_disable_host_auth
Identifiers and References

References:  11, 12, 14, 15, 16, 18, 3, 5, 9, 5.5.6, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.03, DSS06.06, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 7.6, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.2.3, CIP-004-6 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, AC-3, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.AC-4, PR.AC-6, PR.IP-1, PR.PT-3, FIA_UAU.1, 8.3.1, SRG-OS-000480-GPOS-00229, 5.3.9, SV-204435r877377_rule


---
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    storage:
      files:
      - contents:
          source: data:,%23%09%24OpenBSD%3A%20sshd_config%2Cv%201.103%202018%2F04%2F09%2020%3A41%3A22%20tj%20Exp%20%24%0A%0A%23%20This%20is%20the%20sshd%20server%20system-wide%20configuration%20file.%20%20See%0A%23%20sshd_config%285%29%20for%20more%20information.%0A%0A%23%20This%20sshd%20was%20compiled%20with%20PATH%3D%2Fusr%2Flocal%2Fbin%3A%2Fusr%2Fbin%3A%2Fusr%2Flocal%2Fsbin%3A%2Fusr%2Fsbin%0A%0A%23%20The%20strategy%20used%20for%20options%20in%20the%20default%20sshd_config%20shipped%20with%0A%23%20OpenSSH%20is%20to%20specify%20options%20with%20their%20default%20value%20where%0A%23%20possible%2C%20but%20leave%20them%20commented.%20%20Uncommented%20options%20override%20the%0A%23%20default%20value.%0A%0A%23%20If%20you%20want%20to%20change%20the%20port%20on%20a%20SELinux%20system%2C%20you%20have%20to%20tell%0A%23%20SELinux%20about%20this%20change.%0A%23%20semanage%20port%20-a%20-t%20ssh_port_t%20-p%20tcp%20%23PORTNUMBER%0A%23%0A%23Port%2022%0A%23AddressFamily%20any%0A%23ListenAddress%200.0.0.0%0A%23ListenAddress%20%3A%3A%0A%0AHostKey%20%2Fetc%2Fssh%2Fssh_host_rsa_key%0AHostKey%20%2Fetc%2Fssh%2Fssh_host_ecdsa_key%0AHostKey%20%2Fetc%2Fssh%2Fssh_host_ed25519_key%0A%0A%23%20Ciphers%20and%20keying%0ARekeyLimit%20512M%201h%0A%0A%23%20System-wide%20Crypto%20policy%3A%0A%23%20This%20system%20is%20following%20system-wide%20crypto%20policy.%20The%20changes%20to%0A%23%20Ciphers%2C%20MACs%2C%20KexAlgoritms%20and%20GSSAPIKexAlgorithsm%20will%20not%20have%20any%0A%23%20effect%20here.%20They%20will%20be%20overridden%20by%20command-line%20options%20passed%20on%0A%23%20the%20server%20start%20up.%0A%23%20To%20opt%20out%2C%20uncomment%20a%20line%20with%20redefinition%20of%20%20CRYPTO_POLICY%3D%0A%23%20variable%20in%20%20%2Fetc%2Fsysconfig%2Fsshd%20%20to%20overwrite%20the%20policy.%0A%23%20For%20more%20information%2C%20see%20manual%20page%20for%20update-crypto-policies%288%29.%0A%0A%23%20Logging%0A%23SyslogFacility%20AUTH%0ASyslogFacility%20AUTHPRIV%0A%23LogLevel%20INFO%0A%0A%23%20Authentication%3A%0A%0A%23LoginGraceTime%202m%0APermitRootLogin%20no%0AStrictModes%20yes%0A%23MaxAuthTries%206%0A%23MaxSessions%2010%0A%0APubkeyAuthentication%20yes%0A%0A%23%20The%20default%20is%20to%20check%20both%20.ssh%2Fauthorized_keys%20and%20.ssh%2Fauthorized_keys2%0A%23%20but%20this%20is%20overridden%20so%20installations%20will%20only%20check%20.ssh%2Fauthorized_keys%0AAuthorizedKeysFile%09.ssh%2Fauthorized_keys%0A%0A%23AuthorizedPrincipalsFile%20none%0A%0A%23AuthorizedKeysCommand%20none%0A%23AuthorizedKeysCommandUser%20nobody%0A%0A%23%20For%20this%20to%20work%20you%20will%20also%20need%20host%20keys%20in%20%2Fetc%2Fssh%2Fssh_known_hosts%0AHostbasedAuthentication%20no%0A%23%20Change%20to%20yes%20if%20you%20don%27t%20trust%20~%2F.ssh%2Fknown_hosts%20for%0A%23%20HostbasedAuthentication%0AIgnoreUserKnownHosts%20yes%0A%23%20Don%27t%20read%20the%20user%27s%20~%2F.rhosts%20and%20~%2F.shosts%20files%0AIgnoreRhosts%20yes%0A%0A%23%20To%20disable%20tunneled%20clear%20text%20passwords%2C%20change%20to%20no%20here%21%0A%23PasswordAuthentication%20yes%0APermitEmptyPasswords%20no%0APasswordAuthentication%20no%0A%0A%23%20Change%20to%20no%20to%20disable%20s%2Fkey%20passwords%0A%23ChallengeResponseAuthentication%20yes%0AChallengeResponseAuthentication%20no%0A%0A%23%20Kerberos%20options%0AKerberosAuthentication%20no%0A%23KerberosOrLocalPasswd%20yes%0A%23KerberosTicketCleanup%20yes%0A%23KerberosGetAFSToken%20no%0A%23KerberosUseKuserok%20yes%0A%0A%23%20GSSAPI%20options%0AGSSAPIAuthentication%20no%0AGSSAPICleanupCredentials%20no%0A%23GSSAPIStrictAcceptorCheck%20yes%0A%23GSSAPIKeyExchange%20no%0A%23GSSAPIEnablek5users%20no%0A%0A%23%20Set%20this%20to%20%27yes%27%20to%20enable%20PAM%20authentication%2C%20account%20processing%2C%0A%23%20and%20session%20processing.%20If%20this%20is%20enabled%2C%20PAM%20authentication%20will%0A%23%20be%20allowed%20through%20the%20ChallengeResponseAuthentication%20and%0A%23%20PasswordAuthentication.%20%20Depending%20on%20your%20PAM%20configuration%2C%0A%23%20PAM%20authentication%20via%20ChallengeResponseAuthentication%20may%20bypass%0A%23%20the%20setting%20of%20%22PermitRootLogin%20without-password%22.%0A%23%20If%20you%20just%20want%20the%20PAM%20account%20and%20session%20checks%20to%20run%20without%0A%23%20PAM%20authentication%2C%20then%20enable%20this%20but%20set%20PasswordAuthentication%0A%23%20and%20ChallengeResponseAuthentication%20to%20%27no%27.%0A%23%20WARNING%3A%20%27UsePAM%20no%27%20is%20not%20supported%20in%20Fedora%20and%20may%20cause%20several%0A%23%20problems.%0AUsePAM%20yes%0A%0A%23AllowAgentForwarding%20yes%0A%23AllowTcpForwarding%20yes%0A%23GatewayPorts%20no%0AX11Forwarding%20yes%0A%23X11DisplayOffset%2010%0A%23X11UseLocalhost%20yes%0A%23PermitTTY%20yes%0A%0A%23%20It%20is%20recommended%20to%20use%20pam_motd%20in%20%2Fetc%2Fpam.d%2Fsshd%20instead%20of%20PrintMotd%2C%0A%23%20as%20it%20is%20more%20configurable%20and%20versatile%20than%20the%20built-in%20version.%0APrintMotd%20no%0A%0APrintLastLog%20yes%0A%23TCPKeepAlive%20yes%0APermitUserEnvironment%20no%0ACompression%20no%0AClientAliveInterval%20600%0AClientAliveCountMax%200%0A%23UseDNS%20no%0A%23PidFile%20%2Fvar%2Frun%2Fsshd.pid%0A%23MaxStartups%2010%3A30%3A100%0A%23PermitTunnel%20no%0A%23ChrootDirectory%20none%0A%23VersionAddendum%20none%0A%0A%23%20no%20default%20banner%20path%0ABanner%20%2Fetc%2Fissue%0A%0A%23%20Accept%20locale-related%20environment%20variables%0AAcceptEnv%20LANG%20LC_CTYPE%20LC_NUMERIC%20LC_TIME%20LC_COLLATE%20LC_MONETARY%20LC_MESSAGES%0AAcceptEnv%20LC_PAPER%20LC_NAME%20LC_ADDRESS%20LC_TELEPHONE%20LC_MEASUREMENT%0AAcceptEnv%20LC_IDENTIFICATION%20LC_ALL%20LANGUAGE%0AAcceptEnv%20XMODIFIERS%0A%0A%23%20override%20default%20of%20no%20subsystems%0ASubsystem%09sftp%09%2Fusr%2Flibexec%2Fopenssh%2Fsftp-server%0A%0A%23%20Example%20of%20overriding%20settings%20on%20a%20per-user%20basis%0A%23Match%20User%20anoncvs%0A%23%09X11Forwarding%20no%0A%23%09AllowTcpForwarding%20no%0A%23%09PermitTTY%20no%0A%23%09ForceCommand%20cvs%20server%0A%0AUsePrivilegeSeparation%20sandbox
        mode: 0600
        path: /etc/ssh/sshd_config
        overwrite: true

Complexity:low
Disruption:low
Strategy:restrict
- name: Disable Host-Based Authentication
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*HostbasedAuthentication\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*HostbasedAuthentication\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*HostbasedAuthentication\s+
      line: HostbasedAuthentication no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-010470
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - PCI-DSSv4-8.3.1
  - disable_host_auth
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*HostbasedAuthentication\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "HostbasedAuthentication no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "HostbasedAuthentication no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Allow Only SSH Protocol 2   [ref]

Only SSH protocol version 2 connections should be permitted. The default setting in /etc/ssh/sshd_config is correct, and can be verified by ensuring that the following line appears:
Protocol 2
Warning:  As of openssh-server version 7.4 and above, the only protocol supported is version 2, and line
Protocol 2
in /etc/ssh/sshd_config is not necessary.
Rationale:
SSH protocol version 1 is an insecure implementation of the SSH protocol and has many well-known vulnerability exploits. Exploits of the SSH daemon could provide immediate root access to the system.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_sshd_allow_only_protocol2
Identifiers and References

References:  NT007(R1), 1, 12, 15, 16, 5, 8, 5.5.6, APO13.01, DSS01.04, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.13, 3.5.4, CCI-000197, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.4, SR 1.1, SR 1.10, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.6, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, 0487, 1449, 1506, A.11.2.6, A.13.1.1, A.13.2.1, A.14.1.3, A.18.1.4, A.6.2.1, A.6.2.2, A.7.1.1, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.2, A.9.4.3, CIP-003-8 R4.2, CIP-007-3 R5.1, CIP-007-3 R7.1, CM-6(a), AC-17(a), AC-17(2), IA-5(1)(c), SC-13, MA-4(6), PR.AC-1, PR.AC-3, PR.AC-6, PR.AC-7, PR.PT-4, SRG-OS-000074-GPOS-00042, SRG-OS-000480-GPOS-00227, 5.2.2, SV-204594r877396_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Allow Only SSH Protocol 2
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Protocol\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Protocol\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*Protocol\s+
      line: Protocol 2
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-040390
  - NIST-800-171-3.1.13
  - NIST-800-171-3.5.4
  - NIST-800-53-AC-17(2)
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-MA-4(6)
  - NIST-800-53-SC-13
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy
  - sshd_allow_only_protocol2

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^Protocol")

# shellcheck disable=SC2059
printf -v formatted_output "%s %s" "$stripped_key" "2"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^Protocol\\>" "/etc/ssh/sshd_config"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^Protocol\\>.*/$escaped_formatted_output/gi" "/etc/ssh/sshd_config"
else
    if [[ -s "/etc/ssh/sshd_config" ]] && [[ -n "$(tail -c 1 -- "/etc/ssh/sshd_config" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/ssh/sshd_config"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/ssh/sshd_config" >> "/etc/ssh/sshd_config"
    printf '%s\n' "$formatted_output" >> "/etc/ssh/sshd_config"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable Compression Or Set Compression to delayed   [ref]

Compression is useful for slow network connections over long distances but can cause performance issues on local LANs. If use of compression is required, it should be enabled only after a user has authenticated; otherwise, it should be disabled. To disable compression or delay compression until after a user has successfully authenticated, add or correct the following line in the /etc/ssh/sshd_config file:
Compression no
Rationale:
If compression is allowed in an SSH connection prior to authentication, vulnerabilities in the compression software could result in compromise of the system from an unauthenticated connection, potentially with root privileges.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_compression
Identifiers and References

References:  11, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.IP-1, SRG-OS-000480-GPOS-00227, SV-204602r880758_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value var_sshd_disable_compression # promote to variable
  set_fact:
    var_sshd_disable_compression: !!str no
  tags:
    - always

- name: Disable Compression Or Set Compression to delayed
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Compression\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Compression\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*Compression\s+
      line: Compression {{ var_sshd_disable_compression }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ansible_distribution == 'RedHat' and ansible_distribution_version is version('7.4',
    '<')
  tags:
  - DISA-STIG-RHEL-07-040470
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_compression

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { grep -qP "^ID=[\"']?rhel[\"']?$" "/etc/os-release" && { real="$(grep -P "^VERSION_ID=[\"']?[\w.]+[\"']?$" /etc/os-release | sed "s/^VERSION_ID=[\"']\?\([^\"']\+\)[\"']\?$/\1/")"; expected="7.4"; [[ "$real" != "$expected" ]] && printf "%s\n%s" "$real" "$expected" | sort -VC; }; }; then

var_sshd_disable_compression='no'


# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^Compression")

# shellcheck disable=SC2059
printf -v formatted_output "%s %s" "$stripped_key" "$var_sshd_disable_compression"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^Compression\\>" "/etc/ssh/sshd_config"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^Compression\\>.*/$escaped_formatted_output/gi" "/etc/ssh/sshd_config"
else
    if [[ -s "/etc/ssh/sshd_config" ]] && [[ -n "$(tail -c 1 -- "/etc/ssh/sshd_config" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/ssh/sshd_config"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/ssh/sshd_config" >> "/etc/ssh/sshd_config"
    printf '%s\n' "$formatted_output" >> "/etc/ssh/sshd_config"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable SSH Access via Empty Passwords   [ref]

Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used if no value is set for PermitEmptyPasswords.
To explicitly disallow SSH login from accounts with empty passwords, add or correct the following line in /etc/ssh/sshd_config:
PermitEmptyPasswords no
Any accounts with empty passwords should be disabled immediately, and PAM configuration should prevent users from being able to assign themselves empty passwords.
Rationale:
Configuring this setting for the SSH daemon provides additional assurance that remote login via SSH will require a password, even in the event of misconfiguration elsewhere.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_empty_passwords
Identifiers and References

References:  NT007(R17), 11, 12, 13, 14, 15, 16, 18, 3, 5, 9, 5.5.6, APO01.06, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.03, DSS06.06, 3.1.1, 3.1.5, CCI-000366, CCI-000766, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 5.2, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.AC-4, PR.AC-6, PR.DS-5, PR.IP-1, PR.PT-3, FIA_UAU.1, Req-2.2.4, 2.2.6, SRG-OS-000106-GPOS-00053, SRG-OS-000480-GPOS-00229, SRG-OS-000480-GPOS-00227, 5.3.11, SV-204425r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Disable SSH Access via Empty Passwords
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      line: PermitEmptyPasswords no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-010300
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_empty_passwords

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*PermitEmptyPasswords\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "PermitEmptyPasswords no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "PermitEmptyPasswords no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable GSSAPI Authentication   [ref]

Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like GSSAPI.
The default SSH configuration disallows authentications based on GSSAPI. The appropriate configuration is used if no value is set for GSSAPIAuthentication.
To explicitly disable GSSAPI authentication, add or correct the following line in /etc/ssh/sshd_config:
GSSAPIAuthentication no
Rationale:
GSSAPI authentication is used to provide additional authentication mechanisms to applications. Allowing GSSAPI authentication through SSH exposes the system's GSSAPI to remote hosts, increasing the attack surface of the system.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_gssapi_auth
Identifiers and References

References:  11, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.1.12, CCI-000318, CCI-000368, CCI-001812, CCI-001813, CCI-001814, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, 0418, 1055, 1402, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, CM-7(a), CM-7(b), CM-6(a), AC-17(a), PR.IP-1, FTP_ITC_EXT.1, FCS_SSH_EXT.1.2, SRG-OS-000364-GPOS-00151, SRG-OS-000480-GPOS-00227, SV-204598r853993_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Disable GSSAPI Authentication
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*GSSAPIAuthentication\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*GSSAPIAuthentication\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*GSSAPIAuthentication\s+
      line: GSSAPIAuthentication no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040430
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_gssapi_auth

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*GSSAPIAuthentication\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "GSSAPIAuthentication no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "GSSAPIAuthentication no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable Kerberos Authentication   [ref]

Unless needed, SSH should not permit extraneous or unnecessary authentication mechanisms like Kerberos.
The default SSH configuration disallows authentication validation through Kerberos. The appropriate configuration is used if no value is set for KerberosAuthentication.
To explicitly disable Kerberos authentication, add or correct the following line in /etc/ssh/sshd_config:
KerberosAuthentication no
Rationale:
Kerberos authentication for SSH is often implemented using GSSAPI. If Kerberos is enabled through SSH, the SSH daemon provides a means of access to the system's Kerberos implementation. Configuring these settings for the SSH daemon provides additional assurance that remote logon via SSH will not use unused methods of authentication, even in the event of misconfiguration elsewhere.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_kerb_auth
Identifiers and References

References:  11, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.1.12, CCI-000318, CCI-000368, CCI-001812, CCI-001813, CCI-001814, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.IP-1, FTP_ITC_EXT.1, FCS_SSH_EXT.1.2, SRG-OS-000364-GPOS-00151, SRG-OS-000480-GPOS-00227, SV-204599r853994_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Disable Kerberos Authentication
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*KerberosAuthentication\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*KerberosAuthentication\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*KerberosAuthentication\s+
      line: KerberosAuthentication no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040440
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_kerb_auth

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*KerberosAuthentication\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "KerberosAuthentication no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "KerberosAuthentication no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable SSH Support for Rhosts RSA Authentication   [ref]

SSH can allow authentication through the obsolete rsh command through the use of the authenticating user's SSH keys. This should be disabled.

To ensure this behavior is disabled, add or correct the following line in /etc/ssh/sshd_config:
RhostsRSAAuthentication no
Warning:  As of openssh-server version 7.4 and above, the RhostsRSAAuthentication option has been deprecated, and the line
RhostsRSAAuthentication no
in /etc/ssh/sshd_config is not necessary.
Rationale:
Configuring this setting for the SSH daemon provides additional assurance that remote login via SSH will require a password, even in the event of misconfiguration elsewhere.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_rhosts_rsa
Identifiers and References

References:  11, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.IP-1, FIA_UAU.1, SRG-OS-000480-GPOS-00227, SV-204588r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Disable SSH Support for Rhosts RSA Authentication
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*RhostsRSAAuthentication\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*RhostsRSAAuthentication\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*RhostsRSAAuthentication\s+
      line: RhostsRSAAuthentication no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040330
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_rhosts_rsa

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^RhostsRSAAuthentication")

# shellcheck disable=SC2059
printf -v formatted_output "%s %s" "$stripped_key" "no"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^RhostsRSAAuthentication\\>" "/etc/ssh/sshd_config"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^RhostsRSAAuthentication\\>.*/$escaped_formatted_output/gi" "/etc/ssh/sshd_config"
else
    if [[ -s "/etc/ssh/sshd_config" ]] && [[ -n "$(tail -c 1 -- "/etc/ssh/sshd_config" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/ssh/sshd_config"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/ssh/sshd_config" >> "/etc/ssh/sshd_config"
    printf '%s\n' "$formatted_output" >> "/etc/ssh/sshd_config"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Do Not Allow SSH Environment Options   [ref]

Ensure that users are not able to override environment variables of the SSH daemon.
The default SSH configuration disables environment processing. The appropriate configuration is used if no value is set for PermitUserEnvironment.
To explicitly disable Environment options, add or correct the following /etc/ssh/sshd_config:
PermitUserEnvironment no
Rationale:
SSH environment options potentially allow users to bypass access restriction in some configurations.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_do_not_permit_user_env
Identifiers and References

References:  11, 3, 9, 5.5.6, BAI10.01, BAI10.02, BAI10.03, BAI10.05, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.4.3.2, 4.3.4.3.3, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.IP-1, Req-2.2.4, 2.2.6, SRG-OS-000480-GPOS-00229, 5.3.12, SV-204434r877377_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Do Not Allow SSH Environment Options
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitUserEnvironment\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitUserEnvironment\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*PermitUserEnvironment\s+
      line: PermitUserEnvironment no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-010460
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_do_not_permit_user_env

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*PermitUserEnvironment\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "PermitUserEnvironment no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "PermitUserEnvironment no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable Use of Strict Mode Checking   [ref]

SSHs StrictModes option checks file and ownership permissions in the user's home directory .ssh folder before accepting login. If world- writable permissions are found, logon is rejected.
The default SSH configuration has StrictModes enabled. The appropriate configuration is used if no value is set for StrictModes.
To explicitly enable StrictModes in SSH, add or correct the following line in /etc/ssh/sshd_config:
StrictModes yes
Rationale:
If other users have access to modify user-specific SSH configuration files, they may be able to log into the system as another user.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_enable_strictmodes
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, AC-6, AC-17(a), CM-6(a), PR.AC-4, PR.DS-5, SRG-OS-000480-GPOS-00227, SV-204600r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Enable Use of Strict Mode Checking
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*StrictModes\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*StrictModes\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*StrictModes\s+
      line: StrictModes yes
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040450
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_enable_strictmodes

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*StrictModes\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "StrictModes yes" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "StrictModes yes" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable SSH Warning Banner   [ref]

To enable the warning banner and ensure it is consistent across the system, add or correct the following line in /etc/ssh/sshd_config:
Banner /etc/issue
Another section contains information on how to create an appropriate system-wide warning banner.
Rationale:
The warning message reinforces policy awareness during the logon process and facilitates possible legal action against attackers. Alternatively, systems whose ownership should not be obvious should ensure usage of a banner that does not provide easy attribution.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_enable_warning_banner
Identifiers and References

References:  1, 12, 15, 16, 5.5.6, DSS05.04, DSS05.10, DSS06.10, 3.1.9, CCI-000048, CCI-000050, CCI-001384, CCI-001385, CCI-001386, CCI-001387, CCI-001388, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, AC-8(a), AC-8(c), AC-17(a), CM-6(a), PR.AC-7, FTA_TAB.1, Req-2.2.4, 2.2.6, SRG-OS-000023-GPOS-00006, SRG-OS-000228-GPOS-00088, SV-204580r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Enable SSH Warning Banner
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Banner\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Banner\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*Banner\s+
      line: Banner /etc/issue
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-RHEL-07-040170
  - NIST-800-171-3.1.9
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-8(a)
  - NIST-800-53-AC-8(c)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_enable_warning_banner

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*Banner\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "Banner /etc/issue" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "Banner /etc/issue" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable SSH Print Last Log   [ref]

Ensure that SSH will display the date and time of the last successful account logon.
The default SSH configuration enables print of the date and time of the last login. The appropriate configuration is used if no value is set for PrintLastLog.
To explicitly enable LastLog in SSH, add or correct the following line in /etc/ssh/sshd_config:
PrintLastLog yes
Rationale:
Providing users feedback on when account accesses last occurred facilitates user recognition and reporting of unauthorized account use.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_print_last_log
Identifiers and References

References:  1, 12, 15, 16, DSS05.04, DSS05.10, DSS06.10, CCI-000052, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, SR 1.1, SR 1.10, SR 1.2, SR 1.5, SR 1.7, SR 1.8, SR 1.9, A.18.1.4, A.9.2.1, A.9.2.4, A.9.3.1, A.9.4.2, A.9.4.3, AC-9, AC-9(1), PR.AC-7, SRG-OS-000480-GPOS-00227, SV-204591r858477_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: Enable SSH Print Last Log
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PrintLastLog\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PrintLastLog\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*PrintLastLog\s+
      line: PrintLastLog yes
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040360
  - NIST-800-53-AC-9
  - NIST-800-53-AC-9(1)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_print_last_log

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*PrintLastLog\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "PrintLastLog yes" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "PrintLastLog yes" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set LogLevel to INFO   [ref]

The INFO parameter specifices that record login and logout activity will be logged.
The default SSH configuration sets the log level to INFO. The appropriate configuration is used if no value is set for LogLevel.
To explicitly specify the log level in SSH, add or correct the following line in /etc/ssh/sshd_config:
LogLevel INFO
Rationale:
SSH provides several logging levels with varying amounts of verbosity. DEBUG is specifically not recommended other than strictly for debugging SSH communications since it provides so much data that it is difficult to identify important security information. INFO level is the basic level that only records login activity of SSH users. In many situations, such as Incident Response, it is important to determine when a particular user was active on a system. The logout record can eliminate those users who disconnected, which helps narrow the field.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_sshd_set_loglevel_info
Identifiers and References

References:  AC-17(a), CM-6(a), 5.3.5


Complexity:low
Disruption:low
Strategy:restrict
- name: Set LogLevel to INFO
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*LogLevel\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*LogLevel\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*LogLevel\s+
      line: LogLevel INFO
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - low_complexity
  - low_disruption
  - low_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_set_loglevel_info

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*LogLevel\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "LogLevel INFO" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "LogLevel INFO" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Use Only FIPS 140-2 Validated Ciphers   [ref]

Limit the ciphers to those algorithms which are FIPS-approved. Counter (CTR) mode is also preferred over cipher-block chaining (CBC) mode. The following line in /etc/ssh/sshd_config demonstrates use of FIPS-approved ciphers:
Ciphers aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc
The man page sshd_config(5) contains a list of supported ciphers.

Only the following ciphers are FIPS 140-2 certified on Red Hat Enterprise Linux 7:
- aes128-ctr
- aes192-ctr
- aes256-ctr
- aes128-cbc
- aes192-cbc
- aes256-cbc
- 3des-cbc
- rijndael-cbc@lysator.liu.se

Any combination of the above ciphers will pass this check. Official FIPS 140-2 paperwork for Red Hat Enterprise Linux 7 can be found at http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/140sp/140sp2630.pdf The rule is parametrized to use the following ciphers: aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,rijndael-cbc@lysator.liu.se.
Warning:  The system needs to be rebooted for these changes to take effect.
Warning:  System Crypto Modules must be provided by a vendor that undergoes FIPS-140 certifications. FIPS-140 is applicable to all Federal agencies that use cryptographic-based security systems to protect sensitive information in computer and telecommunication systems (including voice systems) as defined in Section 5131 of the Information Technology Management Reform Act of 1996, Public Law 104-106. This standard shall be used in designing and implementing cryptographic modules that Federal departments and agencies operate or are operated for them under contract. See https://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.140-2.pdf To meet this, the system has to have cryptographic software provided by a vendor that has undergone this certification. This means providing documentation, test results, design information, and independent third party review by an accredited lab. While open source software is capable of meeting this, it does not meet FIPS-140 unless the vendor submits to this process.
Rationale:
Unapproved mechanisms that are used for authentication to the cryptographic module are not verified and therefore cannot be relied upon to provide confidentiality or integrity, and system data may be compromised.
Operating systems utilizing encryption are required to use FIPS-compliant mechanisms for authenticating to cryptographic modules.
FIPS 140-2 is the current standard for validating that mechanisms used to access cryptographic modules utilize authentication that meets industry and government requirements. For government systems, this allows Security Levels 1, 2, 3, or 4 for use on Red Hat Enterprise Linux 7.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_use_approved_ciphers
Identifiers and References

References:  1, 11, 12, 14, 15, 16, 18, 3, 5, 6, 8, 9, 5.5.6, APO11.04, APO13.01, BAI03.05, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.06, DSS06.10, MEA02.01, 3.1.13, 3.13.11, 3.13.8, CCI-000068, CCI-000366, CCI-000803, CCI-000877, CCI-002890, CCI-003123, 164.308(b)(1), 164.308(b)(2), 164.312(e)(1), 164.312(e)(2)(i), 164.312(e)(2)(ii), 164.314(b)(2)(i), 4.3.3.2.2, 4.3.3.3.9, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.10, SR 2.11, SR 2.12, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.5.1, A.12.6.2, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.18.1.4, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CM-6(a), AC-17(a), AC-17(2), SC-13, MA-4(6), IA-5(1)(c), SC-12(2), SC-12(3), PR.AC-1, PR.AC-3, PR.AC-4, PR.AC-6, PR.AC-7, PR.IP-1, PR.PT-1, PR.PT-3, PR.PT-4, 2.2.7, SRG-OS-000033-GPOS-00014, SRG-OS-000120-GPOS-00061, SRG-OS-000125-GPOS-00065, SRG-OS-000250-GPOS-00093, SRG-OS-000393-GPOS-00173, SRG-OS-000394-GPOS-00174, 5.3.13


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value sshd_approved_ciphers # promote to variable
  set_fact:
    sshd_approved_ciphers: !!str aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,rijndael-cbc@lysator.liu.se
  tags:
    - always

- name: Use Only FIPS 140-2 Validated Ciphers
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Ciphers\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*Ciphers\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*Ciphers\s+
      line: Ciphers {{ sshd_approved_ciphers }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-AC-17(2)
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-IA-5(1)(c)
  - NIST-800-53-MA-4(6)
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - PCI-DSSv4-2.2.7
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_use_approved_ciphers

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

sshd_approved_ciphers='aes128-ctr,aes192-ctr,aes256-ctr,aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,rijndael-cbc@lysator.liu.se'


# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^Ciphers")

# shellcheck disable=SC2059
printf -v formatted_output "%s %s" "$stripped_key" "$sshd_approved_ciphers"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^Ciphers\\>" "/etc/ssh/sshd_config"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^Ciphers\\>.*/$escaped_formatted_output/gi" "/etc/ssh/sshd_config"
else
    if [[ -s "/etc/ssh/sshd_config" ]] && [[ -n "$(tail -c 1 -- "/etc/ssh/sshd_config" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/ssh/sshd_config"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/ssh/sshd_config" >> "/etc/ssh/sshd_config"
    printf '%s\n' "$formatted_output" >> "/etc/ssh/sshd_config"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Use Only FIPS 140-2 Validated MACs   [ref]

Limit the MACs to those hash algorithms which are FIPS-approved. The following line in /etc/ssh/sshd_config demonstrates use of FIPS-approved MACs:
MACs hmac-sha2-512,hmac-sha2-256,hmac-sha1
The man page sshd_config(5) contains a list of supported MACs.

Only the following message authentication codes are FIPS 140-2 certified on Red Hat Enterprise Linux 7:
- hmac-sha1
- hmac-sha2-256
- hmac-sha2-512
- hmac-sha1-etm@openssh.com
- hmac-sha2-256-etm@openssh.com
- hmac-sha2-512-etm@openssh.com

Any combination of the above MACs will pass this check. Official FIPS 140-2 paperwork for Red Hat Enterprise Linux 7 can be found at http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/140sp/140sp2630.pdf The rule is parametrized to use the following MACs: hmac-sha2-512,hmac-sha2-256,hmac-sha1,hmac-sha1-etm@openssh.com,hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com.
Warning:  The system needs to be rebooted for these changes to take effect.
Warning:  System Crypto Modules must be provided by a vendor that undergoes FIPS-140 certifications. FIPS-140 is applicable to all Federal agencies that use cryptographic-based security systems to protect sensitive information in computer and telecommunication systems (including voice systems) as defined in Section 5131 of the Information Technology Management Reform Act of 1996, Public Law 104-106. This standard shall be used in designing and implementing cryptographic modules that Federal departments and agencies operate or are operated for them under contract. See https://nvlpubs.nist.gov/nistpubs/FIPS/NIST.FIPS.140-2.pdf To meet this, the system has to have cryptographic software provided by a vendor that has undergone this certification. This means providing documentation, test results, design information, and independent third party review by an accredited lab. While open source software is capable of meeting this, it does not meet FIPS-140 unless the vendor submits to this process.
Rationale:
DoD Information Systems are required to use FIPS-approved cryptographic hash functions. The only SSHv2 hash algorithms meeting this requirement is SHA2.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_use_approved_macs
Identifiers and References

References:  1, 12, 13, 15, 16, 5, 8, APO01.06, APO13.01, DSS01.04, DSS05.02, DSS05.03, DSS05.04, DSS05.07, DSS06.02, DSS06.03, 3.1.13, 3.13.11, 3.13.8, CCI-000068, CCI-000803, CCI-000877, CCI-001453, CCI-003123, 164.308(b)(1), 164.308(b)(2), 164.312(e)(1), 164.312(e)(2)(i), 164.312(e)(2)(ii), 164.314(b)(2)(i), 4.3.3.5.1, 4.3.3.6.6, SR 1.1, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.6, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.11.2.6, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.6.2.1, A.6.2.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CM-6(a), AC-17(a), AC-17(2), SC-13, MA-4(6), SC-12(2), SC-12(3), PR.AC-1, PR.AC-3, PR.DS-5, PR.PT-4, 2.2.7, SRG-OS-000125-GPOS-00065, SRG-OS-000250-GPOS-00093, SRG-OS-000394-GPOS-00174, 5.3.14


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value sshd_approved_macs # promote to variable
  set_fact:
    sshd_approved_macs: !!str hmac-sha2-512,hmac-sha2-256,hmac-sha1,hmac-sha1-etm@openssh.com,hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com
  tags:
    - always

- name: Use Only FIPS 140-2 Validated MACs
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*MACs\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*MACs\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*MACs\s+
      line: MACs {{ sshd_approved_macs }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.11
  - NIST-800-171-3.13.8
  - NIST-800-53-AC-17(2)
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-MA-4(6)
  - NIST-800-53-SC-12(2)
  - NIST-800-53-SC-12(3)
  - NIST-800-53-SC-13
  - PCI-DSSv4-2.2.7
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_use_approved_macs

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

sshd_approved_macs='hmac-sha2-512,hmac-sha2-256,hmac-sha1,hmac-sha1-etm@openssh.com,hmac-sha2-256-etm@openssh.com,hmac-sha2-512-etm@openssh.com'


# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^MACs")

# shellcheck disable=SC2059
printf -v formatted_output "%s %s" "$stripped_key" "$sshd_approved_macs"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^MACs\\>" "/etc/ssh/sshd_config"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^MACs\\>.*/$escaped_formatted_output/gi" "/etc/ssh/sshd_config"
else
    if [[ -s "/etc/ssh/sshd_config" ]] && [[ -n "$(tail -c 1 -- "/etc/ssh/sshd_config" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "/etc/ssh/sshd_config"
    fi
    cce=""
    printf '# Per %s: Set %s in %s\n' "${cce}" "${formatted_output}" "/etc/ssh/sshd_config" >> "/etc/ssh/sshd_config"
    printf '%s\n' "$formatted_output" >> "/etc/ssh/sshd_config"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable Use of Privilege Separation   [ref]

When enabled, SSH will create an unprivileged child process that has the privilege of the authenticated user. To enable privilege separation in SSH, add or correct the following line in the /etc/ssh/sshd_config file:
UsePrivilegeSeparation sandbox
Rationale:
SSH daemon privilege separation causes the SSH process to drop root privileges when not needed which would decrease the impact of software vulnerabilities in the unprivileged section.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_use_priv_separation
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.1.12, CCI-000366, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-17(a), AC-6, PR.AC-4, PR.DS-5, SRG-OS-000480-GPOS-00227, SV-204601r603261_rule


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value var_sshd_priv_separation # promote to variable
  set_fact:
    var_sshd_priv_separation: !!str sandbox
  tags:
    - always

- name: Enable Use of Privilege Separation
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*UsePrivilegeSeparation\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*UsePrivilegeSeparation\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*UsePrivilegeSeparation\s+
      line: UsePrivilegeSeparation {{ var_sshd_priv_separation }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040460
  - NIST-800-171-3.1.12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6
  - NIST-800-53-CM-6(a)
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_use_priv_separation

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_sshd_priv_separation='sandbox'


if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*UsePrivilegeSeparation\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "UsePrivilegeSeparation $var_sshd_priv_separation" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "UsePrivilegeSeparation $var_sshd_priv_separation" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Verify Permissions on SSH Server Private *_key Key Files   [ref]

SSH server private keys - files that match the /etc/ssh/*_key glob, have to have restricted permissions. If those files are owned by the root user and the root group, they have to have the 0600 permission or stricter. If they are owned by the root user, but by a dedicated group ssh_keys, they can have the 0640 permission or stricter.
Rationale:
If an unauthorized user obtains the private SSH host key file, the host could be impersonated.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_sshd_private_key
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.1.13, 3.13.10, CCI-000366, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, AC-17(a), CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-2.2.4, 2.2.6, SRG-OS-000480-GPOS-00227, 5.3.2, SV-204597r880743_rule


include ssh_private_key_perms

class ssh_private_key_perms {
  exec { 'sshd_priv_key':
    command => "chmod 0640 /etc/ssh/*_key",
    path    => '/bin:/usr/bin'
  }
}

Complexity:low
Disruption:low
Strategy:configure
- name: Find root:root-owned keys
  ansible.builtin.command: find -H /etc/ssh/ -maxdepth 1 -user root -regex ".*_key$"
    -type f -group root -perm /u+xs,g+xwrs,o+xwrt
  register: root_owned_keys
  changed_when: false
  failed_when: false
  check_mode: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040420
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_private_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set permissions for root:root-owned keys
  ansible.builtin.file:
    path: '{{ item }}'
    mode: u-xs,g-xwrs,o-xwrt
    state: file
  with_items:
  - '{{ root_owned_keys.stdout_lines }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040420
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_private_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Find root:ssh_keys-owned keys
  ansible.builtin.command: find -H /etc/ssh/ -maxdepth 1 -user root -regex ".*_key$"
    -type f -group ssh_keys -perm /u+xs,g+xws,o+xwrt
  register: dedicated_group_owned_keys
  changed_when: false
  failed_when: false
  check_mode: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040420
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_private_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set permissions for root:ssh_keys-owned keys
  ansible.builtin.file:
    path: '{{ item }}'
    mode: u-xs,g-xws,o-xwrt
    state: file
  with_items:
  - '{{ dedicated_group_owned_keys.stdout_lines }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040420
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_private_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

for keyfile in /etc/ssh/*_key; do
    test -f "$keyfile" || continue
    if test root:root = "$(stat -c "%U:%G" "$keyfile")"; then
    
	chmod u-xs,g-xwrs,o-xwrt "$keyfile"
    
    elif test root:ssh_keys = "$(stat -c "%U:%G" "$keyfile")"; then
	chmod u-xs,g-xws,o-xwrt "$keyfile"
    else
        echo "Key-like file '$keyfile' is owned by an unexpected user:group combination"
    fi
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Verify Permissions on SSH Server Public *.pub Key Files   [ref]

To properly set the permissions of /etc/ssh/*.pub, run the command:
$ sudo chmod 0644 /etc/ssh/*.pub
Rationale:
If a public host key file is modified by an unauthorized user, the SSH service may be compromised.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_sshd_pub_key
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 3.1.13, 3.13.10, CCI-000366, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, AC-17(a), CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-2.2.4, 2.2.6, SRG-OS-000480-GPOS-00227, 5.3.3, SV-204596r603261_rule


include ssh_public_key_perms

class ssh_public_key_perms {
  exec { 'sshd_pub_key':
    command => "chmod 0644 /etc/ssh/*.pub",
    path    => '/bin:/usr/bin'
  }
}

Complexity:low
Disruption:low
Strategy:configure
- name: Find /etc/ssh/ file(s)
  command: find -H /etc/ssh/ -maxdepth 1 -perm /u+xs,g+xws,o+xwt  -type f -regex "^.*\.pub$"
  register: files_found
  changed_when: false
  failed_when: false
  check_mode: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040410
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_pub_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Set permissions for /etc/ssh/ file(s)
  file:
    path: '{{ item }}'
    mode: u-xs,g-xws,o-xwt
    state: file
  with_items:
  - '{{ files_found.stdout_lines }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-RHEL-07-040410
  - NIST-800-171-3.1.13
  - NIST-800-171-3.13.10
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - configure_strategy
  - file_permissions_sshd_pub_key
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

find -H /etc/ssh/ -maxdepth 1 -perm /u+xs,g+xws,o+xwt  -type f -regex '^.*\.pub$' -exec chmod u-xs,g-xws,o-xwt {} \;

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   System Security Services Daemon   Group contains 1 rule
[ref]   The System Security Services Daemon (SSSD) is a system daemon that provides access to different identity and authentication providers such as Red Hat's IdM, Microsoft's AD, openLDAP, MIT Kerberos, etc. It uses a common framework that can provide caching and offline support to systems utilizing SSSD. SSSD using caching to reduce load on authentication servers permit offline authentication as well as store extended user data.

For more information, see https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/7/html/system-level_authentication_guide/sssd

Rule   Enable Smartcards in SSSD   [ref]

SSSD should be configured to authenticate access to the system using smart cards. To enable smart cards in SSSD, set pam_cert_auth to True under the [pam] section in /etc/sssd/sssd.conf. For example:
[pam]
pam_cert_auth = True
Rationale:
Using an authentication device, such as a CAC or token that is separate from the information system, ensures that even if the information system is compromised, that compromise will not affect credentials stored on the authentication device.

Multi-Factor Authentication (MFA) solutions that require devices separate from information systems gaining access include, for example, hardware tokens providing time-based or challenge-response authenticators and smart cards such as the U.S. Government Personal Identity Verification card and the DoD Common Access Card.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sssd_enable_smartcards
Identifiers and References

References:  CCI-001954, CCI-000765, CCI-000766, CCI-000767, CCI-000768, 0421, 0422, 0431, 0974, 1173, 1401, 1504, 1505, 1546, 1557, 1558, 1559, 1560, 1561, Req-8.3, 8.4, SRG-OS-000375-GPOS-00160, SRG-OS-000105-GPOS-00052, SRG-OS-000106-GPOS-00053, SRG-OS-000107-GPOS-00054, SRG-OS-000108-GPOS-00055


Complexity:low
Disruption:medium
Strategy:configure
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - sssd_enable_smartcards

- name: Test for domain group
  command: grep '^\s*\[domain\/[^]]*]' /etc/sssd/sssd.conf
  register: test_grep_domain
  ignore_errors: true
  changed_when: false
  check_mode: false
  when:
  - '"sssd-common" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - sssd_enable_smartcards

- name: Add default domain group (if no domain there)
  ini_file:
    path: /etc/sssd/sssd.conf
    section: '{{ item.section }}'
    option: '{{ item.option }}'
    value: '{{ item.value }}'
    create: true
    mode: 384
  with_items:
  - section: sssd
    option: domains
    value: default
  - section: domain/default
    option: id_provider
    value: files
  when:
  - '"sssd-common" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - test_grep_domain.stdout is defined
  - test_grep_domain.stdout | length < 1
  tags:
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - sssd_enable_smartcards

- name: Enable Smartcards in SSSD
  ini_file:
    dest: /etc/sssd/sssd.conf
    section: pam
    option: pam_cert_auth
    value: 'True'
    create: true
    mode: 384
  when:
  - '"sssd-common" in ansible_facts.packages'
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - PCI-DSS-Req-8.3
  - PCI-DSSv4-8.4
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - sssd_enable_smartcards

Complexity:low
Disruption:medium
Strategy:configure
# Remediation is applicable only in certain platforms
if rpm --quiet -q sssd-common && { [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; }; then

found=false

# set value in all files if they contain section or key
for f in $(echo -n "/etc/sssd/sssd.conf"); do
    if [ ! -e "$f" ]; then
        continue
    fi

    # find key in section and change value
    if grep -qzosP "[[:space:]]*\[pam\]([^\n\[]*\n+)+?[[:space:]]*pam_cert_auth" "$f"; then
            sed -i "s/pam_cert_auth[^(\n)]*/pam_cert_auth = True/" "$f"
            found=true

    # find section and add key = value to it
    elif grep -qs "[[:space:]]*\[pam\]" "$f"; then
            sed -i "/[[:space:]]*\[pam\]/a pam_cert_auth = True" "$f"
            found=true
    fi
done

# if section not in any file, append section with key = value to FIRST file in files parameter
if ! $found ; then
    file=$(echo "/etc/sssd/sssd.conf" | cut -f1 -d ' ')
    mkdir -p "$(dirname "$file")"
    echo -e "[pam]\npam_cert_auth = True" >> "$file"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Red Hat and Red Hat Enterprise Linux are either registered trademarks or trademarks of Red Hat, Inc. in the United States and other countries. All other names are registered trademarks or trademarks of their respective companies.