Guide to the Secure Configuration of Ubuntu 20.04

with profile Standard System Security Profile for Ubuntu 20.04
This profile contains rules to ensure standard security baseline of an Ubuntu 20.04 system. Regardless of your system's workload all of these checks should pass.
The SCAP Security Guide Project
https://www.open-scap.org/security-policies/scap-security-guide
This guide presents a catalog of security-relevant configuration settings for Ubuntu 20.04. It is a rendering of content structured in the eXtensible Configuration Checklist Description Format (XCCDF) in order to support security automation. The SCAP content is is available in the scap-security-guide package which is developed at https://www.open-scap.org/security-policies/scap-security-guide.

Providing system administrators with such guidance informs them how to securely configure systems under their control in a variety of network roles. Policy makers and baseline creators can use this catalog of settings, with its associated references to higher-level security control catalogs, in order to assist them in security baseline creation. This guide is a catalog, not a checklist, and satisfaction of every item is not likely to be possible or sensible in many operational scenarios. However, the XCCDF format enables granular selection and adjustment of settings, and their association with OVAL and OCIL content provides an automated checking capability. Transformations of this document, and its associated automated checking content, are capable of providing baselines that meet a diverse set of policy objectives. Some example XCCDF Profiles, which are selections of items that form checklists and can be used as baselines, are available with this guide. They can be processed, in an automated fashion, with tools that support the Security Content Automation Protocol (SCAP). The DISA STIG, which provides required settings for US Department of Defense systems, is one example of a baseline created from this guidance.
Do not attempt to implement any of the settings in this guide without first testing them in a non-operational environment. The creators of this guidance assume no responsibility whatsoever for its use by other parties, and makes no guarantees, expressed or implied, about its quality, reliability, or any other characteristic.

Profile Information

Profile TitleStandard System Security Profile for Ubuntu 20.04
Profile IDxccdf_org.ssgproject.content_profile_standard

CPE Platforms

  • cpe:/o:canonical:ubuntu_linux:20.04::~~lts~~~

Revision History

Current version: 0.1.68

  • draft (as of 2023-06-15)

Table of Contents

  1. System Settings
    1. Installing and Maintaining Software
    2. Account and Access Control
    3. System Accounting with auditd
    4. Configure Syslog
    5. File Permissions and Masks
  2. Services
    1. Apport Service
    2. Cron and At Daemons
    3. Deprecated services
    4. Network Time Protocol
    5. SSH Server

Checklist

Group   Guide to the Secure Configuration of Ubuntu 20.04   Group contains 22 groups and 45 rules
Group   System Settings   Group contains 14 groups and 31 rules
[ref]   Contains rules that check correct system settings.
Group   Installing and Maintaining Software   Group contains 1 group and 5 rules
[ref]   The following sections contain information on security-relevant choices during the initial operating system installation process and the setup of software updates.
Group   Disk Partitioning   Group contains 5 rules
[ref]   To ensure separation and protection of data, there are top-level system directories which should be placed on their own physical partition or logical volume. The installer's default partitioning scheme creates separate logical volumes for /, /boot, and swap.
  • If starting with any of the default layouts, check the box to \"Review and modify partitioning.\" This allows for the easy creation of additional logical volumes inside the volume group already created, though it may require making /'s logical volume smaller to create space. In general, using logical volumes is preferable to using partitions because they can be more easily adjusted later.
  • If creating a custom layout, create the partitions mentioned in the previous paragraph (which the installer will require anyway), as well as separate ones described in the following sections.
If a system has already been installed, and the default partitioning scheme was used, it is possible but nontrivial to modify it to create separate logical volumes for the directories listed above. The Logical Volume Manager (LVM) makes this possible. See the LVM HOWTO at http://tldp.org/HOWTO/LVM-HOWTO/ for more detailed information on LVM.

Rule   Ensure /home Located On Separate Partition   [ref]

If user home directories will be stored locally, create a separate partition for /home at installation time (or migrate it later using LVM). If /home will be mounted from another system such as an NFS server, then creating a separate partition is not necessary at installation time, and the mountpoint can instead be configured later.
Rationale:
Ensuring that /home is mounted on its own partition enables the setting of more restrictive mount options, and also helps ensure that users cannot trivially fill partitions used for log or audit data storage.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_partition_for_home
Identifiers and References

References:  BP28(R12), 12, 15, 8, APO13.01, DSS05.02, CCI-000366, CCI-001208, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.13.1.1, A.13.2.1, A.14.1.3, CM-6(a), SC-5(2), PR.PT-4, SRG-OS-000480-GPOS-00227, 1.1.17

Rule   Ensure /tmp Located On Separate Partition   [ref]

The /tmp directory is a world-writable directory used for temporary file storage. Ensure it has its own partition or logical volume at installation time, or migrate it using LVM.
Rationale:
The /tmp partition is used as temporary storage by many programs. Placing /tmp in its own partition enables the setting of more restrictive mount options, which can help protect programs which use it.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_partition_for_tmp
Identifiers and References

References:  BP28(R12), 12, 15, 8, APO13.01, DSS05.02, CCI-000366, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.13.1.1, A.13.2.1, A.14.1.3, CM-6(a), SC-5(2), PR.PT-4, SRG-OS-000480-GPOS-00227, 1.1.2

Rule   Ensure /var Located On Separate Partition   [ref]

The /var directory is used by daemons and other system services to store frequently-changing data. Ensure that /var has its own partition or logical volume at installation time, or migrate it using LVM.
Rationale:
Ensuring that /var is mounted on its own partition enables the setting of more restrictive mount options. This helps protect system services such as daemons or other programs which use it. It is not uncommon for the /var directory to contain world-writable directories installed by other software packages.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_partition_for_var
Identifiers and References

References:  BP28(R12), 12, 15, 8, APO13.01, DSS05.02, CCI-000366, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.13.1.1, A.13.2.1, A.14.1.3, CM-6(a), SC-5(2), PR.PT-4, SRG-OS-000480-GPOS-00227, 1.1.10

Rule   Ensure /var/log Located On Separate Partition   [ref]

System logs are stored in the /var/log directory. Ensure that /var/log has its own partition or logical volume at installation time, or migrate it using LVM.
Rationale:
Placing /var/log in its own partition enables better separation between log files and other files in /var/.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_partition_for_var_log
Identifiers and References

References:  BP28(R12), BP28(R47), 1, 12, 14, 15, 16, 3, 5, 6, 8, APO11.04, APO13.01, BAI03.05, DSS05.02, DSS05.04, DSS05.07, MEA02.01, CCI-000366, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, CIP-007-3 R6.5, CM-6(a), AU-4, SC-5(2), PR.PT-1, PR.PT-4, SRG-OS-000480-GPOS-00227, 1.1.15

Rule   Ensure /var/log/audit Located On Separate Partition   [ref]

Audit logs are stored in the /var/log/audit directory. Ensure that /var/log/audit has its own partition or logical volume at installation time, or migrate it using LVM. Make absolutely certain that it is large enough to store all audit logs that will be created by the auditing daemon.
Rationale:
Placing /var/log/audit in its own partition enables better separation between audit files and other files, and helps ensure that auditing cannot be halted due to the partition running out of space.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_partition_for_var_log_audit
Identifiers and References

References:  BP28(R43), 1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 8, APO11.04, APO13.01, BAI03.05, BAI04.04, DSS05.02, DSS05.04, DSS05.07, MEA02.01, CCI-000366, CCI-001849, 164.312(a)(2)(ii), 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.2, SR 7.6, A.12.1.3, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.17.2.1, CIP-007-3 R6.5, CM-6(a), AU-4, SC-5(2), PR.DS-4, PR.PT-1, PR.PT-4, FMT_SMF_EXT.1, SRG-OS-000341-GPOS-00132, SRG-OS-000480-GPOS-00227, 1.1.16

Group   Account and Access Control   Group contains 1 group and 1 rule
[ref]   In traditional Unix security, if an attacker gains shell access to a certain login account, they can perform any action or access any file to which that account has access. Therefore, making it more difficult for unauthorized people to gain shell access to accounts, particularly to privileged accounts, is a necessary part of securing a system. This section introduces mechanisms for restricting access to accounts under Ubuntu 20.04.
Group   Secure Session Configuration Files for Login Accounts   Group contains 1 rule
[ref]   When a user logs into a Unix account, the system configures the user's session by reading a number of files. Many of these files are located in the user's home directory, and may have weak permissions as a result of user error or misconfiguration. If an attacker can modify or even read certain types of account configuration information, they can often gain full access to the affected user's account. Therefore, it is important to test and correct configuration file permissions for interactive accounts, particularly those of privileged users such as root or system administrators.

Rule   Ensure users own their home directories   [ref]

The user home directory is space defined for the particular user to set local environment variables and to store personal files. Since the user is accountable for files stored in the user home directory, the user must be the owner of the directory.
Rationale:
Since the user is accountable for files stored in the user home directory, the user must be the owner of the directory.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_accounts_users_own_home_directories
Identifiers and References

References:  6.2.6

Group   System Accounting with auditd   Group contains 2 rules
[ref]   The audit service provides substantial capabilities for recording system activities. By default, the service audits about SELinux AVC denials and certain types of security-relevant events such as system logins, account modifications, and authentication events performed by programs such as sudo. Under its default configuration, auditd has modest disk space requirements, and should not noticeably impact system performance.

NOTE: The Linux Audit daemon auditd can be configured to use the augenrules program to read audit rules files (*.rules) located in /etc/audit/rules.d location and compile them to create the resulting form of the /etc/audit/audit.rules configuration file during the daemon startup (default configuration). Alternatively, the auditd daemon can use the auditctl utility to read audit rules from the /etc/audit/audit.rules configuration file during daemon startup, and load them into the kernel. The expected behavior is configured via the appropriate ExecStartPost directive setting in the /usr/lib/systemd/system/auditd.service configuration file. To instruct the auditd daemon to use the augenrules program to read audit rules (default configuration), use the following setting: 
ExecStartPost=-/sbin/augenrules --load
in the /usr/lib/systemd/system/auditd.service configuration file. In order to instruct the auditd daemon to use the auditctl utility to read audit rules, use the following setting: 
ExecStartPost=-/sbin/auditctl -R /etc/audit/audit.rules
in the /usr/lib/systemd/system/auditd.service configuration file. Refer to [Service] section of the /usr/lib/systemd/system/auditd.service configuration file for further details.

Government networks often have substantial auditing requirements and auditd can be configured to meet these requirements. Examining some example audit records demonstrates how the Linux audit system satisfies common requirements. The following example from Red Hat Enterprise Linux 7 Documentation available at https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/7/html-single/selinux_users_and_administrators_guide/index#sect-Security-Enhanced_Linux-Fixing_Problems-Raw_Audit_Messages shows the substantial amount of information captured in a two typical "raw" audit messages, followed by a breakdown of the most important fields. In this example the message is SELinux-related and reports an AVC denial (and the associated system call) that occurred when the Apache HTTP Server attempted to access the /var/www/html/file1 file (labeled with the samba_share_t type): 
type=AVC msg=audit(1226874073.147:96): avc:  denied  { getattr } for pid=2465 comm="httpd"
path="/var/www/html/file1" dev=dm-0 ino=284133 scontext=unconfined_u:system_r:httpd_t:s0
tcontext=unconfined_u:object_r:samba_share_t:s0 tclass=file

type=SYSCALL msg=audit(1226874073.147:96): arch=40000003 syscall=196 success=no exit=-13
a0=b98df198 a1=bfec85dc a2=54dff4 a3=2008171 items=0 ppid=2463 pid=2465 auid=502 uid=48
gid=48 euid=48 suid=48 fsuid=48 egid=48 sgid=48 fsgid=48 tty=(none) ses=6 comm="httpd"
exe="/usr/sbin/httpd" subj=unconfined_u:system_r:httpd_t:s0 key=(null)
  • msg=audit(1226874073.147:96)
    • The number in parentheses is the unformatted time stamp (Epoch time) for the event, which can be converted to standard time by using the date command.
  • { getattr }
    • The item in braces indicates the permission that was denied. getattr indicates the source process was trying to read the target file's status information. This occurs before reading files. This action is denied due to the file being accessed having the wrong label. Commonly seen permissions include getattr, read, and write.
  • comm="httpd"
    • The executable that launched the process. The full path of the executable is found in the exe= section of the system call (SYSCALL) message, which in this case, is exe="/usr/sbin/httpd".
  • path="/var/www/html/file1"
    • The path to the object (target) the process attempted to access.
  • scontext="unconfined_u:system_r:httpd_t:s0"
    • The SELinux context of the process that attempted the denied action. In this case, it is the SELinux context of the Apache HTTP Server, which is running in the httpd_t domain.
  • tcontext="unconfined_u:object_r:samba_share_t:s0"
    • The SELinux context of the object (target) the process attempted to access. In this case, it is the SELinux context of file1. Note: the samba_share_t type is not accessible to processes running in the httpd_t domain.
  • From the system call (SYSCALL) message, two items are of interest:
    • success=no: indicates whether the denial (AVC) was enforced or not. success=no indicates the system call was not successful (SELinux denied access). success=yes indicates the system call was successful - this can be seen for permissive domains or unconfined domains, such as initrc_t and kernel_t.
    • exe="/usr/sbin/httpd": the full path to the executable that launched the process, which in this case, is exe="/usr/sbin/httpd".

Rule   Ensure the audit Subsystem is Installed   [ref]

The audit package should be installed.
Rationale:
The auditd service is an access monitoring and accounting daemon, watching system calls to audit any access, in comparison with potential local access control policy such as SELinux policy.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_package_audit_installed
Identifiers and References

References:  BP28(R50), CCI-000130, CCI-000131, CCI-000132, CCI-000133, CCI-000134, CCI-000135, CCI-000154, CCI-000158, CCI-000172, CCI-001464, CCI-001487, CCI-001814, CCI-001875, CCI-001876, CCI-001877, CCI-001878, CCI-001879, CCI-001880, CCI-001881, CCI-001882, CCI-001889, CCI-001914, CCI-002884, CCI-000169, CIP-004-6 R3.3, CIP-007-3 R6.5, AC-7(a), AU-7(1), AU-7(2), AU-14, AU-12(2), AU-2(a), CM-6(a), FAU_GEN.1, Req-10.1, 10.2.1, SRG-OS-000062-GPOS-00031, SRG-OS-000037-GPOS-00015, SRG-OS-000038-GPOS-00016, SRG-OS-000039-GPOS-00017, SRG-OS-000040-GPOS-00018, SRG-OS-000041-GPOS-00019, SRG-OS-000042-GPOS-00021, SRG-OS-000051-GPOS-00024, SRG-OS-000054-GPOS-00025, SRG-OS-000122-GPOS-00063, SRG-OS-000254-GPOS-00095, SRG-OS-000255-GPOS-00096, SRG-OS-000337-GPOS-00129, SRG-OS-000348-GPOS-00136, SRG-OS-000349-GPOS-00137, SRG-OS-000350-GPOS-00138, SRG-OS-000351-GPOS-00139, SRG-OS-000352-GPOS-00140, SRG-OS-000353-GPOS-00141, SRG-OS-000354-GPOS-00142, SRG-OS-000358-GPOS-00145, SRG-OS-000365-GPOS-00152, SRG-OS-000392-GPOS-00172, SRG-OS-000475-GPOS-00220, UBTU-20-010182, 4.1.1.1



[[packages]]
name = "auditd"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_auditd

class install_auditd {
  package { 'auditd':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure auditd is installed
  package:
    name: auditd
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-UBTU-20-010182
  - NIST-800-53-AC-7(a)
  - NIST-800-53-AU-12(2)
  - NIST-800-53-AU-14
  - NIST-800-53-AU-2(a)
  - NIST-800-53-AU-7(1)
  - NIST-800-53-AU-7(2)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.1
  - PCI-DSSv4-10.2.1
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - package_audit_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

DEBIAN_FRONTEND=noninteractive apt-get install -y "auditd"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable auditd Service   [ref]

The auditd service is an essential userspace component of the Linux Auditing System, as it is responsible for writing audit records to disk. The auditd service can be enabled with the following command: 
$ sudo systemctl enable auditd.service
Rationale:
Without establishing what type of events occurred, it would be difficult to establish, correlate, and investigate the events leading up to an outage or attack. Ensuring the auditd service is active ensures audit records generated by the kernel are appropriately recorded.

Additionally, a properly configured audit subsystem ensures that actions of individual system users can be uniquely traced to those users so they can be held accountable for their actions.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_auditd_enabled
Identifiers and References

References:  1, 11, 12, 13, 14, 15, 16, 19, 2, 3, 4, 5, 6, 7, 8, 9, 5.4.1.1, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO12.06, APO13.01, BAI03.05, BAI08.02, DSS01.03, DSS01.04, DSS02.02, DSS02.04, DSS02.07, DSS03.01, DSS03.05, DSS05.02, DSS05.03, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, 3.3.1, 3.3.2, 3.3.6, CCI-000126, CCI-000130, CCI-000131, CCI-000132, CCI-000133, CCI-000134, CCI-000135, CCI-000154, CCI-000158, CCI-000172, CCI-000366, CCI-001464, CCI-001487, CCI-001814, CCI-001875, CCI-001876, CCI-001877, CCI-002884, CCI-001878, CCI-001879, CCI-001880, CCI-001881, CCI-001882, CCI-001889, CCI-001914, CCI-000169, 164.308(a)(1)(ii)(D), 164.308(a)(5)(ii)(C), 164.310(a)(2)(iv), 164.310(d)(2)(iii), 164.312(b), 4.2.3.10, 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.3.6.6, 4.3.4.4.7, 4.3.4.5.6, 4.3.4.5.7, 4.3.4.5.8, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 1.13, SR 2.10, SR 2.11, SR 2.12, SR 2.6, SR 2.8, SR 2.9, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 6.1, SR 6.2, SR 7.1, SR 7.6, A.11.2.6, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.7, A.15.2.1, A.15.2.2, A.16.1.4, A.16.1.5, A.16.1.7, A.6.2.1, A.6.2.2, CIP-004-6 R3.3, CIP-007-3 R6.5, AC-2(g), AU-3, AU-10, AU-2(d), AU-12(c), AU-14(1), AC-6(9), CM-6(a), SI-4(23), DE.AE-3, DE.AE-5, DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.AC-3, PR.PT-1, PR.PT-4, RS.AN-1, RS.AN-4, FAU_GEN.1, Req-10.1, 10.2.1, SRG-OS-000062-GPOS-00031, SRG-OS-000037-GPOS-00015, SRG-OS-000038-GPOS-00016, SRG-OS-000039-GPOS-00017, SRG-OS-000040-GPOS-00018, SRG-OS-000041-GPOS-00019, SRG-OS-000042-GPOS-00021, SRG-OS-000051-GPOS-00024, SRG-OS-000054-GPOS-00025, SRG-OS-000122-GPOS-00063, SRG-OS-000254-GPOS-00095, SRG-OS-000255-GPOS-00096, SRG-OS-000337-GPOS-00129, SRG-OS-000348-GPOS-00136, SRG-OS-000349-GPOS-00137, SRG-OS-000350-GPOS-00138, SRG-OS-000351-GPOS-00139, SRG-OS-000352-GPOS-00140, SRG-OS-000353-GPOS-00141, SRG-OS-000354-GPOS-00142, SRG-OS-000358-GPOS-00145, SRG-OS-000365-GPOS-00152, SRG-OS-000392-GPOS-00172, SRG-OS-000475-GPOS-00220, 4.1.1.2



[customizations.services]
enabled = ["auditd"]

Complexity:low
Disruption:low
Strategy:enable
include enable_auditd

class enable_auditd {
  service {'auditd':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.2
  - NIST-800-171-3.3.6
  - NIST-800-53-AC-2(g)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-14(1)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-4(23)
  - PCI-DSS-Req-10.1
  - PCI-DSSv4-10.2.1
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_auditd_enabled

- name: Enable service auditd
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Enable service auditd
    systemd:
      name: auditd
      enabled: 'yes'
      state: started
      masked: 'no'
    when:
    - '"auditd" in ansible_facts.packages'
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - '"auditd" in ansible_facts.packages'
  tags:
  - CJIS-5.4.1.1
  - NIST-800-171-3.3.1
  - NIST-800-171-3.3.2
  - NIST-800-171-3.3.6
  - NIST-800-53-AC-2(g)
  - NIST-800-53-AC-6(9)
  - NIST-800-53-AU-10
  - NIST-800-53-AU-12(c)
  - NIST-800-53-AU-14(1)
  - NIST-800-53-AU-2(d)
  - NIST-800-53-AU-3
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SI-4(23)
  - PCI-DSS-Req-10.1
  - PCI-DSSv4-10.2.1
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_auditd_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { dpkg-query --show --showformat='${db:Status-Status}\n' 'auditd' 2>/dev/null | grep -q installed; }; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'auditd.service'
"$SYSTEMCTL_EXEC" start 'auditd.service'
"$SYSTEMCTL_EXEC" enable 'auditd.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Configure Syslog   Group contains 2 groups and 6 rules
[ref]   The syslog service has been the default Unix logging mechanism for many years. It has a number of downsides, including inconsistent log format, lack of authentication for received messages, and lack of authentication, encryption, or reliable transport for messages sent over a network. However, due to its long history, syslog is a de facto standard which is supported by almost all Unix applications.

In Ubuntu 20.04, rsyslog has replaced ksyslogd as the syslog daemon of choice, and it includes some additional security features such as reliable, connection-oriented (i.e. TCP) transmission of logs, the option to log to database formats, and the encryption of log data en route to a central logging server. This section discusses how to configure rsyslog for best effect, and how to use tools provided with the system to maintain and monitor logs.
Group   Ensure Proper Configuration of Log Files   Group contains 3 rules
[ref]   The file /etc/rsyslog.conf controls where log message are written. These are controlled by lines called rules, which consist of a selector and an action. These rules are often customized depending on the role of the system, the requirements of the environment, and whatever may enable the administrator to most effectively make use of log data. The default rules in Ubuntu 20.04 are: 
*.info;mail.none;authpriv.none;cron.none                /var/log/messages
authpriv.*                                              /var/log/secure
mail.*                                                  -/var/log/maillog
cron.*                                                  /var/log/cron
*.emerg                                                 *
uucp,news.crit                                          /var/log/spooler
local7.*                                                /var/log/boot.log
See the man page rsyslog.conf(5) for more information. Note that the rsyslog daemon can be configured to use a timestamp format that some log processing programs may not understand. If this occurs, edit the file /etc/rsyslog.conf and add or edit the following line: 
$ ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat

Rule   Ensure Log Files Are Owned By Appropriate Group   [ref]

The group-owner of all log files written by rsyslog should be adm. These log files are determined by the second part of each Rule line in /etc/rsyslog.conf and typically all appear in /var/log. For each log file LOGFILE referenced in /etc/rsyslog.conf, run the following command to inspect the file's group owner: 
$ ls -l LOGFILE
If the owner is not adm, run the following command to correct this: 
$ sudo chgrp adm LOGFILE
Rationale:
The log files generated by rsyslog contain valuable information regarding system configuration, user authentication, and other such information. Log files should be protected from unauthorized access.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_rsyslog_files_groupownership
Identifiers and References

References:  BP28(R46), BP28(R5), 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-001314, 4.3.3.7.3, SR 2.1, SR 5.2, 0988, 1405, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-10.5.1, Req-10.5.2, 10.3.1, 10.3.2


Complexity:low
Disruption:medium
Strategy:configure
- name: Ensure Log Files Are Owned By Appropriate Group - Set rsyslog logfile configuration
    facts
  ansible.builtin.set_fact:
    rsyslog_etc_config: /etc/rsyslog.conf
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Get IncludeConfig directive
  ansible.builtin.shell: |
    set -o pipefail
    grep -e '$IncludeConfig' {{ rsyslog_etc_config }} | cut -d ' ' -f 2 || true
  register: rsyslog_old_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Get include files directives
  ansible.builtin.shell: |
    set -o pipefail
    awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' {{ rsyslog_etc_config }} || true
  register: rsyslog_new_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Aggregate rsyslog includes
  ansible.builtin.set_fact:
    include_config_output: '{{ rsyslog_old_inc.stdout_lines + rsyslog_new_inc.stdout_lines
      }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - List all config files
  ansible.builtin.find:
    paths: '{{ item | dirname }}'
    patterns: '{{ item | basename }}'
    hidden: false
    follow: true
  loop: '{{ include_config_output | list + [rsyslog_etc_config] }}'
  register: rsyslog_config_files
  failed_when: false
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Extract log files old format
  ansible.builtin.shell: |
    set -o pipefail
    grep -oP '^[^(\s|#|\$)]+[\s]+.*[\s]+-?(/+[^:;\s]+);*\.*$' {{ item.1.path }} | \
    awk '{print $NF}' | \
    sed -e 's/^-//' || true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_old
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Extract log files new format
  ansible.builtin.shell: |
    set -o pipefail
    grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" {{ item.1.path }} | \
    grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)" | \
    grep -oE "\"([/[:alnum:][:punct:]]*)\"" | \
    tr -d "\""|| true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_new
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group - Sum all log files found
  ansible.builtin.set_fact:
    log_files: '{{ log_files_new.results | map(attribute=''stdout_lines'') | list
      | flatten | unique + log_files_old.results | map(attribute=''stdout_lines'')
      | list | flatten | unique }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership

- name: Ensure Log Files Are Owned By Appropriate Group -Setup log files attribute
  ansible.builtin.file:
    path: '{{ item }}'
    group: '4'
    state: file
  loop: '{{ log_files | list | flatten | unique }}'
  failed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_groupownership


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# List of log file paths to be inspected for correct permissions
# * Primarily inspect log file paths listed in /etc/rsyslog.conf
RSYSLOG_ETC_CONFIG="/etc/rsyslog.conf"
# * And also the log file paths listed after rsyslog's $IncludeConfig directive
#   (store the result into array for the case there's shell glob used as value of IncludeConfig)
readarray -t OLD_INC < <(grep -e "\$IncludeConfig[[:space:]]\+[^[:space:];]\+" /etc/rsyslog.conf | cut -d ' ' -f 2)
readarray -t RSYSLOG_INCLUDE_CONFIG < <(for INCPATH in "${OLD_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)
readarray -t NEW_INC < <(awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' /etc/rsyslog.conf)
readarray -t RSYSLOG_INCLUDE < <(for INCPATH in "${NEW_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)

# Declare an array to hold the final list of different log file paths
declare -a LOG_FILE_PATHS

# Array to hold all rsyslog config entries
RSYSLOG_CONFIGS=()
RSYSLOG_CONFIGS=("${RSYSLOG_ETC_CONFIG}" "${RSYSLOG_INCLUDE_CONFIG[@]}" "${RSYSLOG_INCLUDE[@]}")

# Get full list of files to be checked
# RSYSLOG_CONFIGS may contain globs such as
# /etc/rsyslog.d/*.conf /etc/rsyslog.d/*.frule
# So, loop over the entries in RSYSLOG_CONFIGS and use find to get the list of included files.
RSYSLOG_CONFIG_FILES=()
for ENTRY in "${RSYSLOG_CONFIGS[@]}"
do
	# If directory, rsyslog will search for config files in recursively.
	# However, files in hidden sub-directories or hidden files will be ignored.
	if [ -d "${ENTRY}" ]
	then
		readarray -t FINDOUT < <(find "${ENTRY}" -not -path '*/.*' -type f)
		RSYSLOG_CONFIG_FILES+=("${FINDOUT[@]}")
	elif [ -f "${ENTRY}" ]
	then
		RSYSLOG_CONFIG_FILES+=("${ENTRY}")
	else
		echo "Invalid include object: ${ENTRY}"
	fi
done

# Browse each file selected above as containing paths of log files
# ('/etc/rsyslog.conf' and '/etc/rsyslog.d/*.conf' in the default configuration)
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	# From each of these files extract just particular log file path(s), thus:
	# * Ignore lines starting with space (' '), comment ('#"), or variable syntax ('$') characters,
	# * Ignore empty lines,
	# * Strip quotes and closing brackets from paths.
	# * Ignore paths that match /dev|/etc.*\.conf, as those are paths, but likely not log files
	# * From the remaining valid rows select only fields constituting a log file path
	# Text file column is understood to represent a log file path if and only if all of the
	# following are met:
	# * it contains at least one slash '/' character,
	# * it is preceded by space
	# * it doesn't contain space (' '), colon (':'), and semicolon (';') characters
	# Search log file for path(s) only in case it exists!
	if [[ -f "${LOG_FILE}" ]]
	then
		NORMALIZED_CONFIG_FILE_LINES=$(sed -e "/^[#|$]/d" "${LOG_FILE}")
		LINES_WITH_PATHS=$(grep '[^/]*\s\+\S*/\S\+$' <<< "${NORMALIZED_CONFIG_FILE_LINES}")
		FILTERED_PATHS=$(awk '{if(NF>=2&&($NF~/^\//||$NF~/^-\//)){sub(/^-\//,"/",$NF);print $NF}}' <<< "${LINES_WITH_PATHS}")
		CLEANED_PATHS=$(sed -e "s/[\"')]//g; /\\/etc.*\.conf/d; /\\/dev\\//d" <<< "${FILTERED_PATHS}")
		MATCHED_ITEMS=$(sed -e "/^$/d" <<< "${CLEANED_PATHS}")
		# Since above sed command might return more than one item (delimited by newline), split
		# the particular matches entries into new array specific for this log file
		readarray -t ARRAY_FOR_LOG_FILE <<< "$MATCHED_ITEMS"
		# Concatenate the two arrays - previous content of $LOG_FILE_PATHS array with
		# items from newly created array for this log file
		LOG_FILE_PATHS+=("${ARRAY_FOR_LOG_FILE[@]}")
		# Delete the temporary array
		unset ARRAY_FOR_LOG_FILE
	fi
done

# Check for RainerScript action log format which might be also multiline so grep regex is a bit
# curly:
# extract possibly multiline action omfile expressions
# extract File="logfile" expression
# match only "logfile" expression
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	ACTION_OMFILE_LINES=$(grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" "${LOG_FILE}")
	OMFILE_LINES=$(echo "${ACTION_OMFILE_LINES}"| grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)")
	LOG_FILE_PATHS+=("$(echo "${OMFILE_LINES}"| grep -oE "\"([/[:alnum:][:punct:]]*)\""|tr -d "\"")")
done

# Ensure the correct attribute if file exists
FILE_CMD="chgrp"
for LOG_FILE_PATH in "${LOG_FILE_PATHS[@]}"
do
	# Sanity check - if particular $LOG_FILE_PATH is empty string, skip it from further processing
	if [ -z "$LOG_FILE_PATH" ]
	then
		continue
	fi
	$FILE_CMD "4" "$LOG_FILE_PATH"
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure Log Files Are Owned By Appropriate User   [ref]

The owner of all log files written by rsyslog should be syslog. These log files are determined by the second part of each Rule line in /etc/rsyslog.conf and typically all appear in /var/log. For each log file LOGFILE referenced in /etc/rsyslog.conf, run the following command to inspect the file's owner: 
$ ls -l LOGFILE
If the owner is not syslog, run the following command to correct this: 
$ sudo chown syslog LOGFILE
Rationale:
The log files generated by rsyslog contain valuable information regarding system configuration, user authentication, and other such information. Log files should be protected from unauthorized access.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_rsyslog_files_ownership
Identifiers and References

References:  BP28(R46), BP28(R5), 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-001314, 4.3.3.7.3, SR 2.1, SR 5.2, 0988, 1405, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-10.5.1, Req-10.5.2, 10.3.1, 10.3.2


Complexity:low
Disruption:medium
Strategy:configure
- name: Ensure Log Files Are Owned By Appropriate User - Set rsyslog logfile configuration
    facts
  ansible.builtin.set_fact:
    rsyslog_etc_config: /etc/rsyslog.conf
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Get IncludeConfig directive
  ansible.builtin.shell: |
    set -o pipefail
    grep -e '$IncludeConfig' {{ rsyslog_etc_config }} | cut -d ' ' -f 2 || true
  register: rsyslog_old_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Get include files directives
  ansible.builtin.shell: |
    set -o pipefail
    awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' {{ rsyslog_etc_config }} || true
  register: rsyslog_new_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Aggregate rsyslog includes
  ansible.builtin.set_fact:
    include_config_output: '{{ rsyslog_old_inc.stdout_lines + rsyslog_new_inc.stdout_lines
      }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - List all config files
  ansible.builtin.find:
    paths: '{{ item | dirname }}'
    patterns: '{{ item | basename }}'
    hidden: false
    follow: true
  loop: '{{ include_config_output | list + [rsyslog_etc_config] }}'
  register: rsyslog_config_files
  failed_when: false
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Extract log files old format
  ansible.builtin.shell: |
    set -o pipefail
    grep -oP '^[^(\s|#|\$)]+[\s]+.*[\s]+-?(/+[^:;\s]+);*\.*$' {{ item.1.path }} | \
    awk '{print $NF}' | \
    sed -e 's/^-//' || true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_old
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Extract log files new format
  ansible.builtin.shell: |
    set -o pipefail
    grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" {{ item.1.path }} | \
    grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)" | \
    grep -oE "\"([/[:alnum:][:punct:]]*)\"" | \
    tr -d "\""|| true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_new
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User - Sum all log files found
  ansible.builtin.set_fact:
    log_files: '{{ log_files_new.results | map(attribute=''stdout_lines'') | list
      | flatten | unique + log_files_old.results | map(attribute=''stdout_lines'')
      | list | flatten | unique }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership

- name: Ensure Log Files Are Owned By Appropriate User -Setup log files attribute
  ansible.builtin.file:
    path: '{{ item }}'
    owner: '104'
    state: file
  loop: '{{ log_files | list | flatten | unique }}'
  failed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_ownership


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# List of log file paths to be inspected for correct permissions
# * Primarily inspect log file paths listed in /etc/rsyslog.conf
RSYSLOG_ETC_CONFIG="/etc/rsyslog.conf"
# * And also the log file paths listed after rsyslog's $IncludeConfig directive
#   (store the result into array for the case there's shell glob used as value of IncludeConfig)
readarray -t OLD_INC < <(grep -e "\$IncludeConfig[[:space:]]\+[^[:space:];]\+" /etc/rsyslog.conf | cut -d ' ' -f 2)
readarray -t RSYSLOG_INCLUDE_CONFIG < <(for INCPATH in "${OLD_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)
readarray -t NEW_INC < <(awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' /etc/rsyslog.conf)
readarray -t RSYSLOG_INCLUDE < <(for INCPATH in "${NEW_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)

# Declare an array to hold the final list of different log file paths
declare -a LOG_FILE_PATHS

# Array to hold all rsyslog config entries
RSYSLOG_CONFIGS=()
RSYSLOG_CONFIGS=("${RSYSLOG_ETC_CONFIG}" "${RSYSLOG_INCLUDE_CONFIG[@]}" "${RSYSLOG_INCLUDE[@]}")

# Get full list of files to be checked
# RSYSLOG_CONFIGS may contain globs such as
# /etc/rsyslog.d/*.conf /etc/rsyslog.d/*.frule
# So, loop over the entries in RSYSLOG_CONFIGS and use find to get the list of included files.
RSYSLOG_CONFIG_FILES=()
for ENTRY in "${RSYSLOG_CONFIGS[@]}"
do
	# If directory, rsyslog will search for config files in recursively.
	# However, files in hidden sub-directories or hidden files will be ignored.
	if [ -d "${ENTRY}" ]
	then
		readarray -t FINDOUT < <(find "${ENTRY}" -not -path '*/.*' -type f)
		RSYSLOG_CONFIG_FILES+=("${FINDOUT[@]}")
	elif [ -f "${ENTRY}" ]
	then
		RSYSLOG_CONFIG_FILES+=("${ENTRY}")
	else
		echo "Invalid include object: ${ENTRY}"
	fi
done

# Browse each file selected above as containing paths of log files
# ('/etc/rsyslog.conf' and '/etc/rsyslog.d/*.conf' in the default configuration)
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	# From each of these files extract just particular log file path(s), thus:
	# * Ignore lines starting with space (' '), comment ('#"), or variable syntax ('$') characters,
	# * Ignore empty lines,
	# * Strip quotes and closing brackets from paths.
	# * Ignore paths that match /dev|/etc.*\.conf, as those are paths, but likely not log files
	# * From the remaining valid rows select only fields constituting a log file path
	# Text file column is understood to represent a log file path if and only if all of the
	# following are met:
	# * it contains at least one slash '/' character,
	# * it is preceded by space
	# * it doesn't contain space (' '), colon (':'), and semicolon (';') characters
	# Search log file for path(s) only in case it exists!
	if [[ -f "${LOG_FILE}" ]]
	then
		NORMALIZED_CONFIG_FILE_LINES=$(sed -e "/^[#|$]/d" "${LOG_FILE}")
		LINES_WITH_PATHS=$(grep '[^/]*\s\+\S*/\S\+$' <<< "${NORMALIZED_CONFIG_FILE_LINES}")
		FILTERED_PATHS=$(awk '{if(NF>=2&&($NF~/^\//||$NF~/^-\//)){sub(/^-\//,"/",$NF);print $NF}}' <<< "${LINES_WITH_PATHS}")
		CLEANED_PATHS=$(sed -e "s/[\"')]//g; /\\/etc.*\.conf/d; /\\/dev\\//d" <<< "${FILTERED_PATHS}")
		MATCHED_ITEMS=$(sed -e "/^$/d" <<< "${CLEANED_PATHS}")
		# Since above sed command might return more than one item (delimited by newline), split
		# the particular matches entries into new array specific for this log file
		readarray -t ARRAY_FOR_LOG_FILE <<< "$MATCHED_ITEMS"
		# Concatenate the two arrays - previous content of $LOG_FILE_PATHS array with
		# items from newly created array for this log file
		LOG_FILE_PATHS+=("${ARRAY_FOR_LOG_FILE[@]}")
		# Delete the temporary array
		unset ARRAY_FOR_LOG_FILE
	fi
done

# Check for RainerScript action log format which might be also multiline so grep regex is a bit
# curly:
# extract possibly multiline action omfile expressions
# extract File="logfile" expression
# match only "logfile" expression
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	ACTION_OMFILE_LINES=$(grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" "${LOG_FILE}")
	OMFILE_LINES=$(echo "${ACTION_OMFILE_LINES}"| grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)")
	LOG_FILE_PATHS+=("$(echo "${OMFILE_LINES}"| grep -oE "\"([/[:alnum:][:punct:]]*)\""|tr -d "\"")")
done

# Ensure the correct attribute if file exists
FILE_CMD="chown"
for LOG_FILE_PATH in "${LOG_FILE_PATHS[@]}"
do
	# Sanity check - if particular $LOG_FILE_PATH is empty string, skip it from further processing
	if [ -z "$LOG_FILE_PATH" ]
	then
		continue
	fi
	$FILE_CMD "104" "$LOG_FILE_PATH"
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure System Log Files Have Correct Permissions   [ref]

The file permissions for all log files written by rsyslog should be set to 640, or more restrictive. These log files are determined by the second part of each Rule line in /etc/rsyslog.conf and typically all appear in /var/log. For each log file LOGFILE referenced in /etc/rsyslog.conf, run the following command to inspect the file's permissions: 
$ ls -l LOGFILE
If the permissions are not 640 or more restrictive, run the following command to correct this: 
$ sudo chmod 640 LOGFILE
"
Rationale:
Log files can contain valuable information regarding system configuration. If the system log files are not protected unauthorized users could change the logged data, eliminating their forensic value.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_rsyslog_files_permissions
Identifiers and References

References:  BP28(R36), CCI-001314, 0988, 1405, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), Req-10.5.1, Req-10.5.2, 10.3.1, 10.3.2


Complexity:low
Disruption:medium
Strategy:configure
- name: Ensure System Log Files Have Correct Permissions - Set rsyslog logfile configuration
    facts
  ansible.builtin.set_fact:
    rsyslog_etc_config: /etc/rsyslog.conf
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Get IncludeConfig directive
  ansible.builtin.shell: |
    set -o pipefail
    grep -e '$IncludeConfig' {{ rsyslog_etc_config }} | cut -d ' ' -f 2 || true
  register: rsyslog_old_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Get include files directives
  ansible.builtin.shell: |
    set -o pipefail
    awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' {{ rsyslog_etc_config }} || true
  register: rsyslog_new_inc
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Aggregate rsyslog includes
  ansible.builtin.set_fact:
    include_config_output: '{{ rsyslog_old_inc.stdout_lines + rsyslog_new_inc.stdout_lines
      }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - List all config files
  ansible.builtin.find:
    paths: '{{ item | dirname }}'
    patterns: '{{ item | basename }}'
    hidden: false
    follow: true
  loop: '{{ include_config_output | list + [rsyslog_etc_config] }}'
  register: rsyslog_config_files
  failed_when: false
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Extract log files old format
  ansible.builtin.shell: |
    set -o pipefail
    grep -oP '^[^(\s|#|\$)]+[\s]+.*[\s]+-?(/+[^:;\s]+);*\.*$' {{ item.1.path }} | \
    awk '{print $NF}' | \
    sed -e 's/^-//' || true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_old
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Extract log files new format
  ansible.builtin.shell: |
    set -o pipefail
    grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" {{ item.1.path }} | \
    grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)" | \
    grep -oE "\"([/[:alnum:][:punct:]]*)\"" | \
    tr -d "\""|| true
  loop: '{{ rsyslog_config_files.results | subelements(''files'') }}'
  register: log_files_new
  changed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions - Sum all log files found
  ansible.builtin.set_fact:
    log_files: '{{ log_files_new.results | map(attribute=''stdout_lines'') | list
      | flatten | unique + log_files_old.results | map(attribute=''stdout_lines'')
      | list | flatten | unique }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions

- name: Ensure System Log Files Have Correct Permissions -Setup log files attribute
  ansible.builtin.file:
    path: '{{ item }}'
    mode: '0640'
    state: file
  loop: '{{ log_files | list | flatten | unique }}'
  failed_when: false
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.5.1
  - PCI-DSS-Req-10.5.2
  - PCI-DSSv4-10.3.1
  - PCI-DSSv4-10.3.2
  - configure_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - no_reboot_needed
  - rsyslog_files_permissions


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# List of log file paths to be inspected for correct permissions
# * Primarily inspect log file paths listed in /etc/rsyslog.conf
RSYSLOG_ETC_CONFIG="/etc/rsyslog.conf"
# * And also the log file paths listed after rsyslog's $IncludeConfig directive
#   (store the result into array for the case there's shell glob used as value of IncludeConfig)
readarray -t OLD_INC < <(grep -e "\$IncludeConfig[[:space:]]\+[^[:space:];]\+" /etc/rsyslog.conf | cut -d ' ' -f 2)
readarray -t RSYSLOG_INCLUDE_CONFIG < <(for INCPATH in "${OLD_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)
readarray -t NEW_INC < <(awk '/)/{f=0} /include\(/{f=1} f{nf=gensub("^(include\\(|\\s*)file=\"(\\S+)\".*","\\2",1); if($0!=nf){print nf}}' /etc/rsyslog.conf)
readarray -t RSYSLOG_INCLUDE < <(for INCPATH in "${NEW_INC[@]}"; do eval printf '%s\\n' "${INCPATH}"; done)

# Declare an array to hold the final list of different log file paths
declare -a LOG_FILE_PATHS

# Array to hold all rsyslog config entries
RSYSLOG_CONFIGS=()
RSYSLOG_CONFIGS=("${RSYSLOG_ETC_CONFIG}" "${RSYSLOG_INCLUDE_CONFIG[@]}" "${RSYSLOG_INCLUDE[@]}")

# Get full list of files to be checked
# RSYSLOG_CONFIGS may contain globs such as
# /etc/rsyslog.d/*.conf /etc/rsyslog.d/*.frule
# So, loop over the entries in RSYSLOG_CONFIGS and use find to get the list of included files.
RSYSLOG_CONFIG_FILES=()
for ENTRY in "${RSYSLOG_CONFIGS[@]}"
do
	# If directory, rsyslog will search for config files in recursively.
	# However, files in hidden sub-directories or hidden files will be ignored.
	if [ -d "${ENTRY}" ]
	then
		readarray -t FINDOUT < <(find "${ENTRY}" -not -path '*/.*' -type f)
		RSYSLOG_CONFIG_FILES+=("${FINDOUT[@]}")
	elif [ -f "${ENTRY}" ]
	then
		RSYSLOG_CONFIG_FILES+=("${ENTRY}")
	else
		echo "Invalid include object: ${ENTRY}"
	fi
done

# Browse each file selected above as containing paths of log files
# ('/etc/rsyslog.conf' and '/etc/rsyslog.d/*.conf' in the default configuration)
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	# From each of these files extract just particular log file path(s), thus:
	# * Ignore lines starting with space (' '), comment ('#"), or variable syntax ('$') characters,
	# * Ignore empty lines,
	# * Strip quotes and closing brackets from paths.
	# * Ignore paths that match /dev|/etc.*\.conf, as those are paths, but likely not log files
	# * From the remaining valid rows select only fields constituting a log file path
	# Text file column is understood to represent a log file path if and only if all of the
	# following are met:
	# * it contains at least one slash '/' character,
	# * it is preceded by space
	# * it doesn't contain space (' '), colon (':'), and semicolon (';') characters
	# Search log file for path(s) only in case it exists!
	if [[ -f "${LOG_FILE}" ]]
	then
		NORMALIZED_CONFIG_FILE_LINES=$(sed -e "/^[#|$]/d" "${LOG_FILE}")
		LINES_WITH_PATHS=$(grep '[^/]*\s\+\S*/\S\+$' <<< "${NORMALIZED_CONFIG_FILE_LINES}")
		FILTERED_PATHS=$(awk '{if(NF>=2&&($NF~/^\//||$NF~/^-\//)){sub(/^-\//,"/",$NF);print $NF}}' <<< "${LINES_WITH_PATHS}")
		CLEANED_PATHS=$(sed -e "s/[\"')]//g; /\\/etc.*\.conf/d; /\\/dev\\//d" <<< "${FILTERED_PATHS}")
		MATCHED_ITEMS=$(sed -e "/^$/d" <<< "${CLEANED_PATHS}")
		# Since above sed command might return more than one item (delimited by newline), split
		# the particular matches entries into new array specific for this log file
		readarray -t ARRAY_FOR_LOG_FILE <<< "$MATCHED_ITEMS"
		# Concatenate the two arrays - previous content of $LOG_FILE_PATHS array with
		# items from newly created array for this log file
		LOG_FILE_PATHS+=("${ARRAY_FOR_LOG_FILE[@]}")
		# Delete the temporary array
		unset ARRAY_FOR_LOG_FILE
	fi
done

# Check for RainerScript action log format which might be also multiline so grep regex is a bit
# curly:
# extract possibly multiline action omfile expressions
# extract File="logfile" expression
# match only "logfile" expression
for LOG_FILE in "${RSYSLOG_CONFIG_FILES[@]}"
do
	ACTION_OMFILE_LINES=$(grep -ozP "action\s*\(\s*type\s*=\s*\"omfile\"[^\)]*\)" "${LOG_FILE}")
	OMFILE_LINES=$(echo "${ACTION_OMFILE_LINES}"| grep -aoP "File\s*=\s*\"([/[:alnum:][:punct:]]*)\"\s*\)")
	LOG_FILE_PATHS+=("$(echo "${OMFILE_LINES}"| grep -oE "\"([/[:alnum:][:punct:]]*)\""|tr -d "\"")")
done

# Ensure the correct attribute if file exists
FILE_CMD="chmod"
for LOG_FILE_PATH in "${LOG_FILE_PATHS[@]}"
do
	# Sanity check - if particular $LOG_FILE_PATH is empty string, skip it from further processing
	if [ -z "$LOG_FILE_PATH" ]
	then
		continue
	fi
	$FILE_CMD "0640" "$LOG_FILE_PATH"
done

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Ensure All Logs are Rotated by logrotate   Group contains 1 rule
[ref]   Edit the file /etc/logrotate.d/syslog. Find the first line, which should look like this (wrapped for clarity): 
/var/log/messages /var/log/secure /var/log/maillog /var/log/spooler \
  /var/log/boot.log /var/log/cron {
Edit this line so that it contains a one-space-separated listing of each log file referenced in /etc/rsyslog.conf.

All logs in use on a system must be rotated regularly, or the log files will consume disk space over time, eventually interfering with system operation. The file /etc/logrotate.d/syslog is the configuration file used by the logrotate program to maintain all log files written by syslog. By default, it rotates logs weekly and stores four archival copies of each log. These settings can be modified by editing /etc/logrotate.conf, but the defaults are sufficient for purposes of this guide.

Note that logrotate is run nightly by the cron job /etc/cron.daily/logrotate. If particularly active logs need to be rotated more often than once a day, some other mechanism must be used.

Rule   Ensure Logrotate Runs Periodically   [ref]

The logrotate utility allows for the automatic rotation of log files. The frequency of rotation is specified in /etc/logrotate.conf, which triggers a cron task or a timer. To configure logrotate to run daily, add or correct the following line in /etc/logrotate.conf: 
# rotate log files frequency
daily
Rationale:
Log files that are not properly rotated run the risk of growing so large that they fill up the /var/log partition. Valuable logging information could be lost if the /var/log partition becomes full.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_ensure_logrotate_activated
Identifiers and References

References:  BP28(R43), NT12(R18), 1, 14, 15, 16, 3, 5, 6, APO11.04, BAI03.05, DSS05.04, DSS05.07, MEA02.01, CCI-000366, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, CM-6(a), PR.PT-1, Req-10.7, 10.5.1, 4.3


Complexity:low
Disruption:low
Strategy:configure
- name: Configure daily log rotation in /etc/logrotate.conf
  lineinfile:
    create: true
    dest: /etc/logrotate.conf
    regexp: ^daily$
    line: daily
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.7
  - PCI-DSSv4-10.5.1
  - configure_strategy
  - ensure_logrotate_activated
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Make sure daily log rotation setting is not overriden in /etc/logrotate.conf
  lineinfile:
    create: false
    dest: /etc/logrotate.conf
    regexp: ^[\s]*(weekly|monthly|yearly)$
    state: absent
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.7
  - PCI-DSSv4-10.5.1
  - configure_strategy
  - ensure_logrotate_activated
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Configure cron.daily if not already
  block:

  - name: Add shebang
    lineinfile:
      path: /etc/cron.daily/logrotate
      line: '#!/bin/sh'
      insertbefore: BOF
      create: true

  - name: Add logrotate call
    lineinfile:
      path: /etc/cron.daily/logrotate
      line: /usr/sbin/logrotate /etc/logrotate.conf
      regexp: ^[\s]*/usr/sbin/logrotate[\s\S]*/etc/logrotate.conf$
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.7
  - PCI-DSSv4-10.5.1
  - configure_strategy
  - ensure_logrotate_activated
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

LOGROTATE_CONF_FILE="/etc/logrotate.conf"

CRON_DAILY_LOGROTATE_FILE="/etc/cron.daily/logrotate"


# daily rotation is configured
grep -q "^daily$" $LOGROTATE_CONF_FILE|| echo "daily" >> $LOGROTATE_CONF_FILE

# remove any line configuring weekly, monthly or yearly rotation
sed -i '/^\s*\(weekly\|monthly\|yearly\).*$/d' $LOGROTATE_CONF_FILE


# configure cron.daily if not already
if ! grep -q "^[[:space:]]*/usr/sbin/logrotate[[:alnum:][:blank:][:punct:]]*$LOGROTATE_CONF_FILE$" $CRON_DAILY_LOGROTATE_FILE; then
	echo '#!/bin/sh' > $CRON_DAILY_LOGROTATE_FILE
	echo "/usr/sbin/logrotate $LOGROTATE_CONF_FILE" >> $CRON_DAILY_LOGROTATE_FILE
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Ensure rsyslog is Installed   [ref]

Rsyslog is installed by default. The rsyslog package can be installed with the following command: 
 $ apt-get install rsyslog
Rationale:
The rsyslog package provides the rsyslog daemon, which provides system logging services.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_package_rsyslog_installed
Identifiers and References

References:  1, 14, 15, 16, 3, 5, 6, APO11.04, BAI03.05, DSS05.04, DSS05.07, MEA02.01, CCI-001311, CCI-001312, CCI-000366, 164.312(a)(2)(ii), 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, CM-6(a), PR.PT-1, FTP_ITC_EXT.1.1, SRG-OS-000479-GPOS-00224, SRG-OS-000051-GPOS-00024, SRG-OS-000480-GPOS-00227, 4.2.1.1



[[packages]]
name = "rsyslog"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_rsyslog

class install_rsyslog {
  package { 'rsyslog':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure rsyslog is installed
  package:
    name: rsyslog
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - package_rsyslog_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

DEBIAN_FRONTEND=noninteractive apt-get install -y "rsyslog"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable rsyslog Service   [ref]

The rsyslog service provides syslog-style logging by default on Ubuntu 20.04. The rsyslog service can be enabled with the following command: 
$ sudo systemctl enable rsyslog.service
Rationale:
The rsyslog service must be running in order to provide logging services, which are essential to system administration.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_rsyslog_enabled
Identifiers and References

References:  1, 12, 13, 14, 15, 16, 2, 3, 5, 6, 7, 8, 9, APO10.01, APO10.03, APO10.04, APO10.05, APO11.04, APO13.01, BAI03.05, BAI04.04, DSS01.03, DSS03.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, MEA01.01, MEA01.02, MEA01.03, MEA01.04, MEA01.05, MEA02.01, CCI-001311, CCI-001312, CCI-001557, CCI-001851, CCI-000366, 164.312(a)(2)(ii), 4.3.2.6.7, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, SR 6.1, SR 6.2, SR 7.1, SR 7.2, A.12.1.3, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, A.14.2.7, A.15.2.1, A.15.2.2, A.17.2.1, CM-6(a), AU-4(1), DE.CM-1, DE.CM-3, DE.CM-7, ID.SC-4, PR.DS-4, PR.PT-1, SRG-OS-000480-GPOS-00227, UBTU-20-010432, 4.2.1.2



[customizations.services]
enabled = ["rsyslog"]

Complexity:low
Disruption:low
Strategy:enable
include enable_rsyslog

class enable_rsyslog {
  service {'rsyslog':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Enable service rsyslog
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Enable service rsyslog
    systemd:
      name: rsyslog
      enabled: 'yes'
      state: started
      masked: 'no'
    when:
    - '"rsyslog" in ansible_facts.packages'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-UBTU-20-010432
  - NIST-800-53-AU-4(1)
  - NIST-800-53-CM-6(a)
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_rsyslog_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'rsyslog.service'
"$SYSTEMCTL_EXEC" start 'rsyslog.service'
"$SYSTEMCTL_EXEC" enable 'rsyslog.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   File Permissions and Masks   Group contains 5 groups and 17 rules
[ref]   Traditional Unix security relies heavily on file and directory permissions to prevent unauthorized users from reading or modifying files to which they should not have access.

Several of the commands in this section search filesystems for files or directories with certain characteristics, and are intended to be run on every local partition on a given system. When the variable PART appears in one of the commands below, it means that the command is intended to be run repeatedly, with the name of each local partition substituted for PART in turn.

The following command prints a list of all xfs partitions on the local system, which is the default filesystem for Ubuntu 20.04 installations: 
$ mount -t xfs | awk '{print $3}'
For any systems that use a different local filesystem type, modify this command as appropriate.
Group   Verify Permissions on Important Files and Directories   Group contains 1 group and 15 rules
[ref]   Permissions for many files on a system must be set restrictively to ensure sensitive information is properly protected. This section discusses important permission restrictions which can be verified to ensure that no harmful discrepancies have arisen.
Group   Verify Permissions on Files with Local Account Information and Credentials   Group contains 12 rules

Rule   Verify Group Who Owns group File   [ref]

To properly set the group owner of /etc/group, run the command: 
$ sudo chgrp root /etc/group
Rationale:
The /etc/group file contains information regarding groups that are configured on the system. Protection of this file is important for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_groupowner_etc_group
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.5


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/group
  stat:
    path: /etc/group
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure group owner 0 on /etc/group
  file:
    path: /etc/group
    group: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chgrp 0 /etc/group

Rule   Verify Group Who Owns gshadow File   [ref]

To properly set the group owner of /etc/gshadow, run the command: 
$ sudo chgrp shadow /etc/gshadow
Rationale:
The /etc/gshadow file contains group password hashes. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_groupowner_etc_gshadow
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, SRG-OS-000480-GPOS-00227, 6.1.9


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/gshadow
  stat:
    path: /etc/gshadow
  register: file_exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_groupowner_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure group owner 42 on /etc/gshadow
  file:
    path: /etc/gshadow
    group: '42'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_groupowner_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chgrp 42 /etc/gshadow

Rule   Verify Group Who Owns passwd File   [ref]

To properly set the group owner of /etc/passwd, run the command: 
$ sudo chgrp root /etc/passwd
Rationale:
The /etc/passwd file contains information about the users that are configured on the system. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_groupowner_etc_passwd
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.2


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/passwd
  stat:
    path: /etc/passwd
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure group owner 0 on /etc/passwd
  file:
    path: /etc/passwd
    group: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chgrp 0 /etc/passwd

Rule   Verify Group Who Owns shadow File   [ref]

To properly set the group owner of /etc/shadow, run the command: 
$ sudo chgrp shadow /etc/shadow
Rationale:
The /etc/shadow file stores password hashes. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_groupowner_etc_shadow
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.4


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/shadow
  stat:
    path: /etc/shadow
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure group owner 42 on /etc/shadow
  file:
    path: /etc/shadow
    group: '42'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_groupowner_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chgrp 42 /etc/shadow

Rule   Verify User Who Owns group File   [ref]

To properly set the owner of /etc/group, run the command: 
$ sudo chown root /etc/group
Rationale:
The /etc/group file contains information regarding groups that are configured on the system. Protection of this file is important for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_owner_etc_group
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.5


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/group
  stat:
    path: /etc/group
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure owner 0 on /etc/group
  file:
    path: /etc/group
    owner: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chown 0 /etc/group

Rule   Verify User Who Owns gshadow File   [ref]

To properly set the owner of /etc/gshadow, run the command: 
$ sudo chown root /etc/gshadow
Rationale:
The /etc/gshadow file contains group password hashes. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_owner_etc_gshadow
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, SRG-OS-000480-GPOS-00227, 6.1.9


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/gshadow
  stat:
    path: /etc/gshadow
  register: file_exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_owner_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure owner 0 on /etc/gshadow
  file:
    path: /etc/gshadow
    owner: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_owner_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chown 0 /etc/gshadow

Rule   Verify User Who Owns passwd File   [ref]

To properly set the owner of /etc/passwd, run the command: 
$ sudo chown root /etc/passwd
Rationale:
The /etc/passwd file contains information about the users that are configured on the system. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_owner_etc_passwd
Identifiers and References

References:  12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.2


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/passwd
  stat:
    path: /etc/passwd
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure owner 0 on /etc/passwd
  file:
    path: /etc/passwd
    owner: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chown 0 /etc/passwd

Rule   Verify User Who Owns shadow File   [ref]

To properly set the owner of /etc/shadow, run the command: 
$ sudo chown root /etc/shadow
Rationale:
The /etc/shadow file contains the list of local system accounts and stores password hashes. Protection of this file is critical for system security. Failure to give ownership of this file to root provides the designated owner with access to sensitive information which could weaken the system security posture.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_owner_etc_shadow
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.4


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/shadow
  stat:
    path: /etc/shadow
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure owner 0 on /etc/shadow
  file:
    path: /etc/shadow
    owner: '0'
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_owner_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure
chown 0 /etc/shadow

Rule   Verify Permissions on group File   [ref]

To properly set the permissions of /etc/passwd, run the command: 
$ sudo chmod 0644 /etc/passwd
Rationale:
The /etc/group file contains information regarding groups that are configured on the system. Protection of this file is important for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_etc_group
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.5


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/group
  stat:
    path: /etc/group
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure permission u-xs,g-xws,o-xwt on /etc/group
  file:
    path: /etc/group
    mode: u-xs,g-xws,o-xwt
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_group
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure





chmod u-xs,g-xws,o-xwt /etc/group

Rule   Verify Permissions on gshadow File   [ref]

To properly set the permissions of /etc/gshadow, run the command: 
$ sudo chmod 0640 /etc/gshadow
Rationale:
The /etc/gshadow file contains group password hashes. Protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_etc_gshadow
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, SRG-OS-000480-GPOS-00227, 6.1.9


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/gshadow
  stat:
    path: /etc/gshadow
  register: file_exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_permissions_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure permission u-xs,g-xws,o-xwrt on /etc/gshadow
  file:
    path: /etc/gshadow
    mode: u-xs,g-xws,o-xwrt
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - configure_strategy
  - file_permissions_etc_gshadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure





chmod u-xs,g-xws,o-xwrt /etc/gshadow

Rule   Verify Permissions on passwd File   [ref]

To properly set the permissions of /etc/passwd, run the command: 
$ sudo chmod 0644 /etc/passwd
Rationale:
If the /etc/passwd file is writable by a group-owner or the world the risk of its compromise is increased. The file contains the list of accounts on the system and associated information, and protection of this file is critical for system security.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_etc_passwd
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.2


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/passwd
  stat:
    path: /etc/passwd
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure permission u-xs,g-xws,o-xwt on /etc/passwd
  file:
    path: /etc/passwd
    mode: u-xs,g-xws,o-xwt
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_passwd
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure





chmod u-xs,g-xws,o-xwt /etc/passwd

Rule   Verify Permissions on shadow File   [ref]

To properly set the permissions of /etc/shadow, run the command: 
$ sudo chmod 0640 /etc/shadow
Rationale:
The /etc/shadow file contains the list of local system accounts and stores password hashes. Protection of this file is critical for system security. Failure to give ownership of this file to root provides the designated owner with access to sensitive information which could weaken the system security posture.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_etc_shadow
Identifiers and References

References:  BP28(R36), 12, 13, 14, 15, 16, 18, 3, 5, 5.5.2.2, APO01.06, DSS05.04, DSS05.07, DSS06.02, CCI-002223, 4.3.3.7.3, SR 2.1, SR 5.2, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 R2.3, CIP-007-3 R2.1, CIP-007-3 R2.2, CIP-007-3 R2.3, CIP-007-3 R5.1, CIP-007-3 R5.1.1, CIP-007-3 R5.1.2, CM-6(a), AC-6(1), PR.AC-4, PR.DS-5, Req-8.7.c, 7.2.6, SRG-OS-000480-GPOS-00227, 6.1.4


Complexity:low
Disruption:low
Strategy:configure
- name: Test for existence /etc/shadow
  stat:
    path: /etc/shadow
  register: file_exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

- name: Ensure permission u-xs,g-xws,o-xwrt on /etc/shadow
  file:
    path: /etc/shadow
    mode: u-xs,g-xws,o-xwrt
  when: file_exists.stat is defined and file_exists.stat.exists
  tags:
  - CJIS-5.5.2.2
  - NIST-800-53-AC-6(1)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-8.7.c
  - PCI-DSSv4-7.2.6
  - configure_strategy
  - file_permissions_etc_shadow
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed

Complexity:low
Disruption:low
Strategy:configure





chmod u-xs,g-xws,o-xwrt /etc/shadow

Rule   Verify that local System.map file (if exists) is readable only by root   [ref]

Files containing sensitive informations should be protected by restrictive permissions. Most of the time, there is no need that these files need to be read by any non-root user To properly set the permissions of /boot/System.map-*, run the command: 
$ sudo chmod 0600 /boot/System.map-*
Rationale:
The System.map file contains information about kernel symbols and can give some hints to generate local exploitation.
Severity: 
unknown
Rule ID:xccdf_org.ssgproject.content_rule_file_permissions_systemmap
Identifiers and References

References:  BP28(R13)

Group   Restrict Programs from Dangerous Execution Patterns   Group contains 2 groups and 2 rules
[ref]   The recommendations in this section are designed to ensure that the system's features to protect against potentially dangerous program execution are activated. These protections are applied at the system initialization or kernel level, and defend against certain types of badly-configured or compromised programs.
Group   Disable Core Dumps   Group contains 1 rule
[ref]   A core dump file is the memory image of an executable program when it was terminated by the operating system due to errant behavior. In most cases, only software developers legitimately need to access these files. The core dump files may also contain sensitive information, or unnecessarily occupy large amounts of disk space.

Once a hard limit is set in /etc/security/limits.conf, or to a file within the /etc/security/limits.d/ directory, a user cannot increase that limit within his or her own session. If access to core dumps is required, consider restricting them to only certain users or groups. See the limits.conf man page for more information.

The core dumps of setuid programs are further protected. The sysctl variable fs.suid_dumpable controls whether the kernel allows core dumps from these programs at all. The default value of 0 is recommended.

Rule   Disable Core Dumps for SUID programs   [ref]

To set the runtime status of the fs.suid_dumpable kernel parameter, run the following command: 
$ sudo sysctl -w fs.suid_dumpable=0
To make sure that the setting is persistent, add the following line to a file in the directory /etc/sysctl.d: 
fs.suid_dumpable = 0
Rationale:
The core dump of a setuid program is more likely to contain sensitive data, as the program itself runs with greater privileges than the user who initiated execution of the program. Disabling the ability for any setuid program to write a core file decreases the risk of unauthorized access of such data.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sysctl_fs_suid_dumpable
Identifiers and References

References:  BP28(R23), 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), SI-11(a), SI-11(b), 3.3.1.1, 3.3.1.2, 3.3.1.3, 1.6.4


Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: List /etc/sysctl.d/*.conf files
  find:
    paths:
    - /etc/sysctl.d/
    - /run/sysctl.d/
    - /usr/local/lib/sysctl.d/
    - /usr/lib/sysctl.d/
    contains: ^[\s]*fs.suid_dumpable.*$
    patterns: '*.conf'
    file_type: any
  register: find_sysctl_d
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-SI-11(a)
  - NIST-800-53-SI-11(b)
  - PCI-DSSv4-3.3.1.1
  - PCI-DSSv4-3.3.1.2
  - PCI-DSSv4-3.3.1.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_fs_suid_dumpable

- name: Comment out any occurrences of fs.suid_dumpable from config files
  replace:
    path: '{{ item.path }}'
    regexp: ^[\s]*fs.suid_dumpable
    replace: '#fs.suid_dumpable'
  loop: '{{ find_sysctl_d.files }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-SI-11(a)
  - NIST-800-53-SI-11(b)
  - PCI-DSSv4-3.3.1.1
  - PCI-DSSv4-3.3.1.2
  - PCI-DSSv4-3.3.1.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_fs_suid_dumpable

- name: Ensure sysctl fs.suid_dumpable is set to 0
  sysctl:
    name: fs.suid_dumpable
    value: '0'
    sysctl_file: /etc/sysctl.conf
    state: present
    reload: true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-SI-11(a)
  - NIST-800-53-SI-11(b)
  - PCI-DSSv4-3.3.1.1
  - PCI-DSSv4-3.3.1.2
  - PCI-DSSv4-3.3.1.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_fs_suid_dumpable

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Comment out any occurrences of fs.suid_dumpable from /etc/sysctl.d/*.conf files

for f in /etc/sysctl.d/*.conf /run/sysctl.d/*.conf /usr/local/lib/sysctl.d/*.conf /usr/lib/sysctl.d/*.conf; do

  matching_list=$(grep -P '^(?!#).*[\s]*fs.suid_dumpable.*$' $f | uniq )
  if ! test -z "$matching_list"; then
    while IFS= read -r entry; do
      escaped_entry=$(sed -e 's|/|\\/|g' <<< "$entry")
      # comment out "fs.suid_dumpable" matches to preserve user data
      sed -i "s/^${escaped_entry}$/# &/g" $f
    done <<< "$matching_list"
  fi
done

#
# Set sysctl config file which to save the desired value
#

SYSCONFIG_FILE="/etc/sysctl.conf"


#
# Set runtime for fs.suid_dumpable
#
/sbin/sysctl -q -n -w fs.suid_dumpable="0"

#
# If fs.suid_dumpable present in /etc/sysctl.conf, change value to "0"
#	else, add "fs.suid_dumpable = 0" to /etc/sysctl.conf
#

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^fs.suid_dumpable")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "0"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^fs.suid_dumpable\\>" "${SYSCONFIG_FILE}"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^fs.suid_dumpable\\>.*/$escaped_formatted_output/gi" "${SYSCONFIG_FILE}"
else
    if [[ -s "${SYSCONFIG_FILE}" ]] && [[ -n "$(tail -c 1 -- "${SYSCONFIG_FILE}" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "${SYSCONFIG_FILE}"
    fi
    printf '%s\n' "$formatted_output" >> "${SYSCONFIG_FILE}"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Enable ExecShield   Group contains 1 rule
[ref]   ExecShield describes kernel features that provide protection against exploitation of memory corruption errors such as buffer overflows. These features include random placement of the stack and other memory regions, prevention of execution in memory that should only hold data, and special handling of text buffers. These protections are enabled by default on 32-bit systems and controlled through sysctl variables kernel.exec-shield and kernel.randomize_va_space. On the latest 64-bit systems, kernel.exec-shield cannot be enabled or disabled with sysctl.

Rule   Enable Randomized Layout of Virtual Address Space   [ref]

To set the runtime status of the kernel.randomize_va_space kernel parameter, run the following command: 
$ sudo sysctl -w kernel.randomize_va_space=2
To make sure that the setting is persistent, add the following line to a file in the directory /etc/sysctl.d: 
kernel.randomize_va_space = 2
Rationale:
Address space layout randomization (ASLR) makes it more difficult for an attacker to predict the location of attack code they have introduced into a process's address space during an attempt at exploitation. Additionally, ASLR makes it more difficult for an attacker to know the location of existing code in order to re-purpose it using return oriented programming (ROP) techniques.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sysctl_kernel_randomize_va_space
Identifiers and References

References:  BP28(R23), 3.1.7, CCI-000366, CCI-002824, 164.308(a)(1)(ii)(D), 164.308(a)(3), 164.308(a)(4), 164.310(b), 164.310(c), 164.312(a), 164.312(e), CIP-002-5 R1.1, CIP-002-5 R1.2, CIP-003-8 R5.1.1, CIP-003-8 R5.3, CIP-004-6 4.1, CIP-004-6 4.2, CIP-004-6 R2.2.3, CIP-004-6 R2.2.4, CIP-004-6 R2.3, CIP-004-6 R4, CIP-005-6 R1, CIP-005-6 R1.1, CIP-005-6 R1.2, CIP-007-3 R3, CIP-007-3 R3.1, CIP-007-3 R5.1, CIP-007-3 R5.1.2, CIP-007-3 R5.1.3, CIP-007-3 R5.2.1, CIP-007-3 R5.2.3, CIP-007-3 R8.4, CIP-009-6 R.1.1, CIP-009-6 R4, SC-30, SC-30(2), CM-6(a), Req-2.2.1, 2.2.3, SRG-OS-000433-GPOS-00193, SRG-OS-000480-GPOS-00227, UBTU-20-010448, 1.6.2


Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
- name: List /etc/sysctl.d/*.conf files
  find:
    paths:
    - /etc/sysctl.d/
    - /run/sysctl.d/
    - /usr/local/lib/sysctl.d/
    - /usr/lib/sysctl.d/
    contains: ^[\s]*kernel.randomize_va_space.*$
    patterns: '*.conf'
    file_type: any
  register: find_sysctl_d
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-UBTU-20-010448
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

- name: Comment out any occurrences of kernel.randomize_va_space from config files
  replace:
    path: '{{ item.path }}'
    regexp: ^[\s]*kernel.randomize_va_space
    replace: '#kernel.randomize_va_space'
  loop: '{{ find_sysctl_d.files }}'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-UBTU-20-010448
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

- name: Ensure sysctl kernel.randomize_va_space is set to 2
  sysctl:
    name: kernel.randomize_va_space
    value: '2'
    sysctl_file: /etc/sysctl.conf
    state: present
    reload: true
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - DISA-STIG-UBTU-20-010448
  - NIST-800-171-3.1.7
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-30
  - NIST-800-53-SC-30(2)
  - PCI-DSS-Req-2.2.1
  - PCI-DSSv4-2.2.3
  - disable_strategy
  - low_complexity
  - medium_disruption
  - medium_severity
  - reboot_required
  - sysctl_kernel_randomize_va_space

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

# Comment out any occurrences of kernel.randomize_va_space from /etc/sysctl.d/*.conf files

for f in /etc/sysctl.d/*.conf /run/sysctl.d/*.conf /usr/local/lib/sysctl.d/*.conf /usr/lib/sysctl.d/*.conf; do

  matching_list=$(grep -P '^(?!#).*[\s]*kernel.randomize_va_space.*$' $f | uniq )
  if ! test -z "$matching_list"; then
    while IFS= read -r entry; do
      escaped_entry=$(sed -e 's|/|\\/|g' <<< "$entry")
      # comment out "kernel.randomize_va_space" matches to preserve user data
      sed -i "s/^${escaped_entry}$/# &/g" $f
    done <<< "$matching_list"
  fi
done

#
# Set sysctl config file which to save the desired value
#

SYSCONFIG_FILE="/etc/sysctl.conf"


#
# Set runtime for kernel.randomize_va_space
#
/sbin/sysctl -q -n -w kernel.randomize_va_space="2"

#
# If kernel.randomize_va_space present in /etc/sysctl.conf, change value to "2"
#	else, add "kernel.randomize_va_space = 2" to /etc/sysctl.conf
#

# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^kernel.randomize_va_space")

# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "2"

# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^kernel.randomize_va_space\\>" "${SYSCONFIG_FILE}"; then
    escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
    LC_ALL=C sed -i --follow-symlinks "s/^kernel.randomize_va_space\\>.*/$escaped_formatted_output/gi" "${SYSCONFIG_FILE}"
else
    if [[ -s "${SYSCONFIG_FILE}" ]] && [[ -n "$(tail -c 1 -- "${SYSCONFIG_FILE}" || true)" ]]; then
        LC_ALL=C sed -i --follow-symlinks '$a'\\ "${SYSCONFIG_FILE}"
    fi
    printf '%s\n' "$formatted_output" >> "${SYSCONFIG_FILE}"
fi

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Services   Group contains 6 groups and 14 rules
[ref]   The best protection against vulnerable software is running less software. This section describes how to review the software which Ubuntu 20.04 installs on a system and disable software which is not needed. It then enumerates the software packages installed on a default Ubuntu 20.04 system and provides guidance about which ones can be safely disabled.

Ubuntu 20.04 provides a convenient minimal install option that essentially installs the bare necessities for a functional system. When building Ubuntu 20.04 systems, it is highly recommended to select the minimal packages and then build up the system from there.
Group   Apport Service   Group contains 1 rule
[ref]   The Apport service provides debugging and crash reporting features on Ubuntu distributions.

Rule   Disable Apport Service   [ref]

The Apport modifies certain kernel configuration values at runtime which may decrease the overall security of the system and expose sensitive data. The apport service can be disabled with the following command: 
$ sudo systemctl mask --now apport.service
Rationale:
The Apport service modifies the kernel fs.suid_dumpable configuration at runtime which prevents other hardening from being persistent. Disabling the service prevents this behavior.
Severity: 
unknown
Rule ID:xccdf_org.ssgproject.content_rule_service_apport_disabled
Identifiers and References

Complexity:low
Disruption:medium
Reboot:true
Strategy:disable
apiVersion: machineconfiguration.openshift.io/v1
kind: MachineConfig
spec:
  config:
    ignition:
      version: 3.1.0
    systemd:
      units:
      - name: apport.service
        enabled: false
        mask: true
      - name: apport.socket
        enabled: false
        mask: true



[customizations.services]
disabled = ["apport"]

Complexity:low
Disruption:low
Strategy:enable
include disable_apport

class disable_apport {
  service {'apport':
    enable => false,
    ensure => 'stopped',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Block Disable service apport
  block:

  - name: Disable service apport
    block:

    - name: Disable service apport
      systemd:
        name: apport.service
        enabled: 'no'
        state: stopped
        masked: 'yes'
    rescue:

    - name: Intentionally ignored previous 'Disable service apport' failure, service
        was already disabled
      meta: noop
  tags:
  - disable_strategy
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - service_apport_disabled
  - unknown_severity

- name: Unit Socket Exists - apport.socket
  command: systemctl list-unit-files apport.socket
  register: socket_file_exists
  changed_when: false
  failed_when: socket_file_exists.rc not in [0, 1]
  check_mode: false
  tags:
  - disable_strategy
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - service_apport_disabled
  - unknown_severity

- name: Disable socket apport
  systemd:
    name: apport.socket
    enabled: 'no'
    state: stopped
    masked: 'yes'
  when: '"apport.socket" in socket_file_exists.stdout_lines[1]'
  tags:
  - disable_strategy
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - service_apport_disabled
  - unknown_severity

Complexity:low
Disruption:low
Strategy:disable


SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" stop 'apport.service'
"$SYSTEMCTL_EXEC" disable 'apport.service'
"$SYSTEMCTL_EXEC" mask 'apport.service'
# Disable socket activation if we have a unit file for it
if "$SYSTEMCTL_EXEC" -q list-unit-files apport.socket; then
    "$SYSTEMCTL_EXEC" stop 'apport.socket'
    "$SYSTEMCTL_EXEC" mask 'apport.socket'
fi
# The service may not be running because it has been started and failed,
# so let's reset the state so OVAL checks pass.
# Service should be 'inactive', not 'failed' after reboot though.
"$SYSTEMCTL_EXEC" reset-failed 'apport.service' || true
Group   Cron and At Daemons   Group contains 2 rules
[ref]   The cron and at services are used to allow commands to be executed at a later time. The cron service is required by almost all systems to perform necessary maintenance tasks, while at may or may not be required on a given system. Both daemons should be configured defensively.

Rule   Install the cron service   [ref]

The Cron service should be installed.
Rationale:
The cron service allow periodic job execution, needed for almost all administrative tasks and services (software update, log rotating, etc.). Access to cron service should be restricted to administrative accounts only.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_package_cron_installed
Identifiers and References

References:  BP28(R50), 11, 14, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.05, DSS06.06, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, A.9.1.2, CM-6(a), PR.IP-1, PR.PT-3, 5.1.1



[[packages]]
name = "cron"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_cron

class install_cron {
  package { 'cron':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure cron is installed
  package:
    name: cron
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - package_cron_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

DEBIAN_FRONTEND=noninteractive apt-get install -y "cron"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable cron Service   [ref]

The crond service is used to execute commands at preconfigured times. It is required by almost all systems to perform necessary maintenance tasks, such as notifying root of system activity. The cron service can be enabled with the following command: 
$ sudo systemctl enable cron.service
Rationale:
Due to its usage for maintenance and security-supporting tasks, enabling the cron daemon is essential.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_service_cron_enabled
Identifiers and References

References:  11, 14, 3, 9, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.05, DSS06.06, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 7.6, A.12.1.2, A.12.5.1, A.12.6.2, A.14.2.2, A.14.2.3, A.14.2.4, A.9.1.2, CM-6(a), PR.IP-1, PR.PT-3, 2.2.6, 5.1.1



[customizations.services]
enabled = ["cron"]

Complexity:low
Disruption:low
Strategy:enable
include enable_cron

class enable_cron {
  service {'cron':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Enable service cron
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Enable service cron
    systemd:
      name: cron
      enabled: 'yes'
      state: started
      masked: 'no'
    when:
    - '"cron" in ansible_facts.packages'
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - PCI-DSSv4-2.2.6
  - enable_strategy
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - service_cron_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'cron.service'
"$SYSTEMCTL_EXEC" start 'cron.service'
"$SYSTEMCTL_EXEC" enable 'cron.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   Deprecated services   Group contains 5 rules
[ref]   Some deprecated software services impact the overall system security due to their behavior (leak of confidentiality in network exchange, usage as uncontrolled communication channel, risk associated with the service due to its old age, etc.

Rule   Uninstall the inet-based telnet server   [ref]

The inet-based telnet daemon should be uninstalled.
Rationale:
telnet allows clear text communications, and does not protect any data transmission between client and server. Any confidential data can be listened and no integrity checking is made.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_package_inetutils-telnetd_removed
Identifiers and References

References:  NT007(R03), 11, 12, 14, 15, 3, 8, 9, APO13.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.05, DSS06.06, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.2.1, A.6.2.2, A.9.1.2, CM-7(a), CM-7(b), CM-6(a), PR.AC-3, PR.IP-1, PR.PT-3, PR.PT-4


Complexity:low
Disruption:low
Strategy:disable
include remove_inetutils-telnetd

class remove_inetutils-telnetd {
  package { 'inetutils-telnetd':
    ensure => 'purged',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Ensure inetutils-telnetd is removed
  package:
    name: inetutils-telnetd
    state: absent
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - disable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - package_inetutils-telnetd_removed

Complexity:low
Disruption:low
Strategy:disable

# CAUTION: This remediation script will remove inetutils-telnetd
#	   from the system, and may remove any packages
#	   that depend on inetutils-telnetd. Execute this
#	   remediation AFTER testing on a non-production
#	   system!

DEBIAN_FRONTEND=noninteractive apt-get remove -y "inetutils-telnetd"

Rule   Uninstall the nis package   [ref]

The support for Yellowpages should not be installed unless it is required.
Rationale:
NIS is the historical SUN service for central account management, more and more replaced by LDAP. NIS does not support efficiently security constraints, ACL, etc. and should not be used.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_package_nis_removed
Identifiers and References

References:  2.2.17


Complexity:low
Disruption:low
Strategy:disable
include remove_nis

class remove_nis {
  package { 'nis':
    ensure => 'purged',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Ensure nis is removed
  package:
    name: nis
    state: absent
  tags:
  - disable_strategy
  - low_complexity
  - low_disruption
  - low_severity
  - no_reboot_needed
  - package_nis_removed

Complexity:low
Disruption:low
Strategy:disable

# CAUTION: This remediation script will remove nis
#	   from the system, and may remove any packages
#	   that depend on nis. Execute this
#	   remediation AFTER testing on a non-production
#	   system!

DEBIAN_FRONTEND=noninteractive apt-get remove -y "nis"

Rule   Uninstall the ntpdate package   [ref]

ntpdate is a historical ntp synchronization client for unixes. It sould be uninstalled.
Rationale:
ntpdate is an old not security-compliant ntp client. It should be replaced by modern ntp clients such as ntpd, able to use cryptographic mechanisms integrated in NTP.
Severity: 
low
Rule ID:xccdf_org.ssgproject.content_rule_package_ntpdate_removed
Identifiers and References

Complexity:low
Disruption:low
Strategy:disable
include remove_ntpdate

class remove_ntpdate {
  package { 'ntpdate':
    ensure => 'purged',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Ensure ntpdate is removed
  package:
    name: ntpdate
    state: absent
  tags:
  - disable_strategy
  - low_complexity
  - low_disruption
  - low_severity
  - no_reboot_needed
  - package_ntpdate_removed

Complexity:low
Disruption:low
Strategy:disable

# CAUTION: This remediation script will remove ntpdate
#	   from the system, and may remove any packages
#	   that depend on ntpdate. Execute this
#	   remediation AFTER testing on a non-production
#	   system!

DEBIAN_FRONTEND=noninteractive apt-get remove -y "ntpdate"

Rule   Uninstall the ssl compliant telnet server   [ref]

The telnet daemon, even with ssl support, should be uninstalled.
Rationale:
telnet, even with ssl support, should not be installed. When remote shell is required, up-to-date ssh daemon can be used.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_package_telnetd-ssl_removed
Identifiers and References

References:  NT007(R02), 11, 12, 14, 15, 3, 8, 9, APO13.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.05, DSS06.06, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.2.1, A.6.2.2, A.9.1.2, CM-7(a), CM-7(b), CM-6(a), PR.AC-3, PR.IP-1, PR.PT-3, PR.PT-4


Complexity:low
Disruption:low
Strategy:disable
include remove_telnetd-ssl

class remove_telnetd-ssl {
  package { 'telnetd-ssl':
    ensure => 'purged',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Ensure telnetd-ssl is removed
  package:
    name: telnetd-ssl
    state: absent
  tags:
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - disable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - package_telnetd-ssl_removed

Complexity:low
Disruption:low
Strategy:disable

# CAUTION: This remediation script will remove telnetd-ssl
#	   from the system, and may remove any packages
#	   that depend on telnetd-ssl. Execute this
#	   remediation AFTER testing on a non-production
#	   system!

DEBIAN_FRONTEND=noninteractive apt-get remove -y "telnetd-ssl"

Rule   Uninstall the telnet server   [ref]

The telnet daemon should be uninstalled.
Rationale:
telnet allows clear text communications, and does not protect any data transmission between client and server. Any confidential data can be listened and no integrity checking is made.'
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_package_telnetd_removed
Identifiers and References

References:  BP28(R1), NT007(R03), 11, 12, 14, 15, 3, 8, 9, APO13.01, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS01.04, DSS05.02, DSS05.03, DSS05.05, DSS06.06, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 3.1, SR 3.5, SR 3.8, SR 4.1, SR 4.3, SR 5.1, SR 5.2, SR 5.3, SR 7.1, SR 7.6, A.11.2.6, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.2.1, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.2.1, A.6.2.2, A.9.1.2, CM-7(a), CM-7(b), CM-6(a), PR.AC-3, PR.IP-1, PR.PT-3, PR.PT-4, UBTU-20-010405


Complexity:low
Disruption:low
Strategy:disable
include remove_telnetd

class remove_telnetd {
  package { 'telnetd':
    ensure => 'purged',
  }
}

Complexity:low
Disruption:low
Strategy:disable
- name: Ensure telnetd is removed
  package:
    name: telnetd
    state: absent
  tags:
  - DISA-STIG-UBTU-20-010405
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - disable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - package_telnetd_removed

Complexity:low
Disruption:low
Strategy:disable

# CAUTION: This remediation script will remove telnetd
#	   from the system, and may remove any packages
#	   that depend on telnetd. Execute this
#	   remediation AFTER testing on a non-production
#	   system!

DEBIAN_FRONTEND=noninteractive apt-get remove -y "telnetd"
Group   Network Time Protocol   Group contains 2 rules
[ref]   The Network Time Protocol is used to manage the system clock over a network. Computer clocks are not very accurate, so time will drift unpredictably on unmanaged systems. Central time protocols can be used both to ensure that time is consistent among a network of systems, and that their time is consistent with the outside world.

If every system on a network reliably reports the same time, then it is much easier to correlate log messages in case of an attack. In addition, a number of cryptographic protocols (such as Kerberos) use timestamps to prevent certain types of attacks. If your network does not have synchronized time, these protocols may be unreliable or even unusable.

Depending on the specifics of the network, global time accuracy may be just as important as local synchronization, or not very important at all. If your network is connected to the Internet, using a public timeserver (or one provided by your enterprise) provides globally accurate timestamps which may be essential in investigating or responding to an attack which originated outside of your network.

A typical network setup involves a small number of internal systems operating as NTP servers, and the remainder obtaining time information from those internal servers.

There is a choice between the daemons ntpd and chronyd, which are available from the repositories in the ntp and chrony packages respectively.

The default chronyd daemon can work well when external time references are only intermittently accesible, can perform well even when the network is congested for longer periods of time, can usually synchronize the clock faster and with better time accuracy, and quickly adapts to sudden changes in the rate of the clock, for example, due to changes in the temperature of the crystal oscillator. Chronyd should be considered for all systems which are frequently suspended or otherwise intermittently disconnected and reconnected to a network. Mobile and virtual systems for example.

The ntpd NTP daemon fully supports NTP protocol version 4 (RFC 5905), including broadcast, multicast, manycast clients and servers, and the orphan mode. It also supports extra authentication schemes based on public-key cryptography (RFC 5906). The NTP daemon (ntpd) should be considered for systems which are normally kept permanently on. Systems which are required to use broadcast or multicast IP, or to perform authentication of packets with the Autokey protocol, should consider using ntpd.

Refer to https://help.ubuntu.com/lts/serverguide/NTP.html for more detailed comparison of features of chronyd and ntpd daemon features respectively, and for further guidance how to choose between the two NTP daemons.

The upstream manual pages at http://chrony.tuxfamily.org/manual.html for chronyd and http://www.ntp.org for ntpd provide additional information on the capabilities and configuration of each of the NTP daemons.

Rule   Install the systemd_timesyncd Service   [ref]

The systemd_timesyncd service should be installed.
Rationale:
Time synchronization (using NTP) is required by almost all network and administrative tasks (syslog, cryptographic based services (authentication, etc.), etc.). systemd_timesyncd is a part of the systemd suite and acts as a NTP client.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_package_timesyncd_installed
Identifiers and References

References:  NT012(R03), 1, 14, 15, 16, 3, 5, 6, APO11.04, BAI03.05, DSS05.04, DSS05.07, MEA02.01, CCI-000160, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, CM-6(a), PR.PT-1, Req-10.4, 2.2.1.1



[[packages]]
name = "systemd-timesyncd"
version = "*"

Complexity:low
Disruption:low
Strategy:enable
include install_systemd-timesyncd

class install_systemd-timesyncd {
  package { 'systemd-timesyncd':
    ensure => 'installed',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Ensure systemd-timesyncd is installed
  package:
    name: systemd-timesyncd
    state: present
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.4
  - enable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - package_timesyncd_installed

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

DEBIAN_FRONTEND=noninteractive apt-get install -y "systemd-timesyncd"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Enable systemd_timesyncd Service   [ref]

The systemd_timesyncd service can be enabled with the following command: 
$ sudo systemctl enable systemd_timesyncd.service
Rationale:
Enabling the systemd_timesyncd service ensures that this host uses the ntp protocol to fetch time data from a ntp server. Synchronizing time is essential for authentication services such as Kerberos, but it is also important for maintaining accurate logs and auditing possible security breaches.

Additional information on Ubuntu network time protocol is available at https://help.ubuntu.com/lts/serverguide/NTP.html.en.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_service_timesyncd_enabled
Identifiers and References

References:  NT012(R03), 1, 14, 15, 16, 3, 5, 6, APO11.04, BAI03.05, DSS05.04, DSS05.07, MEA02.01, CCI-000160, 4.3.3.3.9, 4.3.3.5.8, 4.3.4.4.7, 4.4.2.1, 4.4.2.2, 4.4.2.4, SR 2.10, SR 2.11, SR 2.12, SR 2.8, SR 2.9, A.12.4.1, A.12.4.2, A.12.4.3, A.12.4.4, A.12.7.1, CM-6(a), AU-8(1)(a), PR.PT-1, Req-10.4, 10.6.1, 2.2.1.2



[customizations.services]
enabled = ["systemd-timesyncd"]

Complexity:low
Disruption:low
Strategy:enable
include enable_systemd-timesyncd

class enable_systemd-timesyncd {
  service {'systemd-timesyncd':
    enable => true,
    ensure => 'running',
  }
}

Complexity:low
Disruption:low
Strategy:enable
- name: Gather the package facts
  package_facts:
    manager: auto
  tags:
  - NIST-800-53-AU-8(1)(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.4
  - PCI-DSSv4-10.6.1
  - enable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - service_timesyncd_enabled

- name: Enable service systemd-timesyncd
  block:

  - name: Gather the package facts
    package_facts:
      manager: auto

  - name: Enable service systemd-timesyncd
    systemd:
      name: systemd-timesyncd
      enabled: 'yes'
      state: started
      masked: 'no'
    when:
    - '"systemd" in ansible_facts.packages'
  when:
  - ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  - ( not ( "chrony" in ansible_facts.packages ) and not ( "ntp" in ansible_facts.packages
    ) )
  tags:
  - NIST-800-53-AU-8(1)(a)
  - NIST-800-53-CM-6(a)
  - PCI-DSS-Req-10.4
  - PCI-DSSv4-10.6.1
  - enable_strategy
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - service_timesyncd_enabled

Complexity:low
Disruption:low
Strategy:enable
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ] && { ( ! ( dpkg-query --show --showformat='${db:Status-Status}\n' 'chrony' 2>/dev/null | grep -q installed ) && ! ( dpkg-query --show --showformat='${db:Status-Status}\n' 'ntp' 2>/dev/null | grep -q installed ) ); }; then

SYSTEMCTL_EXEC='/usr/bin/systemctl'
"$SYSTEMCTL_EXEC" unmask 'systemd-timesyncd.service'
"$SYSTEMCTL_EXEC" start 'systemd-timesyncd.service'
"$SYSTEMCTL_EXEC" enable 'systemd-timesyncd.service'

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Group   SSH Server   Group contains 1 group and 4 rules
[ref]   The SSH protocol is recommended for remote login and remote file transfer. SSH provides confidentiality and integrity for data exchanged between two systems, as well as server authentication, through the use of public key cryptography. The implementation included with the system is called OpenSSH, and more detailed documentation is available from its website, https://www.openssh.com. Its server program is called sshd and provided by the RPM package openssh-server.
Group   Configure OpenSSH Server if Necessary   Group contains 4 rules
[ref]   If the system needs to act as an SSH server, then certain changes should be made to the OpenSSH daemon configuration file /etc/ssh/sshd_config. The following recommendations can be applied to this file. See the sshd_config(5) man page for more detailed information.

Rule   Set SSH Client Alive Count Max   [ref]

The SSH server sends at most ClientAliveCountMax messages during a SSH session and waits for a response from the SSH client. The option ClientAliveInterval configures timeout after each ClientAliveCountMax message. If the SSH server does not receive a response from the client, then the connection is considered unresponsive and terminated. For SSH earlier than v8.2, a ClientAliveCountMax value of 0 causes a timeout precisely when the ClientAliveInterval is set. Starting with v8.2, a value of 0 disables the timeout functionality completely. If the option is set to a number greater than 0, then the session will be disconnected after ClientAliveInterval * ClientAliveCountMax seconds without receiving a keep alive message.
Rationale:
This ensures a user login will be terminated as soon as the ClientAliveInterval is reached.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_set_keepalive
Identifiers and References

References:  BP28(R29), 1, 12, 13, 14, 15, 16, 18, 3, 5, 7, 8, 5.5.6, APO13.01, BAI03.01, BAI03.02, BAI03.03, DSS01.03, DSS03.05, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.11, CCI-000879, CCI-001133, CCI-002361, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 6.2, A.12.4.1, A.12.4.3, A.14.1.1, A.14.2.1, A.14.2.5, A.18.1.4, A.6.1.2, A.6.1.5, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.3, CIP-007-3 R5.1, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, AC-2(5), AC-12, AC-17(a), SC-10, CM-6(a), DE.CM-1, DE.CM-3, PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.IP-2, Req-8.1.8, 8.2.8, SRG-OS-000163-GPOS-00072, SRG-OS-000279-GPOS-00109, UBTU-20-010036, 5.2.15


Complexity:low
Disruption:low
Strategy:restrict
- name: XCCDF Value var_sshd_set_keepalive # promote to variable
  set_fact:
    var_sshd_set_keepalive: !!str 0
  tags:
    - always

- name: Set SSH Client Alive Count Max
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveCountMax\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*ClientAliveCountMax\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*ClientAliveCountMax\s+
      line: ClientAliveCountMax {{ var_sshd_set_keepalive }}
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-UBTU-20-010036
  - NIST-800-171-3.1.11
  - NIST-800-53-AC-12
  - NIST-800-53-AC-17(a)
  - NIST-800-53-AC-2(5)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-SC-10
  - PCI-DSS-Req-8.1.8
  - PCI-DSSv4-8.2.8
  - low_complexity
  - low_disruption
  - medium_severity
  - no_reboot_needed
  - restrict_strategy
  - sshd_set_keepalive


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

var_sshd_set_keepalive='0'


if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*ClientAliveCountMax\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "ClientAliveCountMax $var_sshd_set_keepalive" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "ClientAliveCountMax $var_sshd_set_keepalive" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Set SSH Client Alive Interval   [ref]

SSH allows administrators to set a network responsiveness timeout interval. After this interval has passed, the unresponsive client will be automatically logged out.

To set this timeout interval, edit the following line in /etc/ssh/sshd_config as follows: 
ClientAliveInterval 300


The timeout interval is given in seconds. For example, have a timeout of 10 minutes, set interval to 600.

If a shorter timeout has already been set for the login shell, that value will preempt any SSH setting made in /etc/ssh/sshd_config. Keep in mind that some processes may stop SSH from correctly detecting that the user is idle.
Warning:  SSH disconnecting unresponsive clients will not have desired effect without also configuring ClientAliveCountMax in the SSH service configuration.
Warning:  Following conditions may prevent the SSH session to time out:
  • Remote processes on the remote machine generates output. As the output has to be transferred over the network to the client, the timeout is reset every time such transfer happens.
  • Any scp or sftp activity by the same user to the host resets the timeout.
Rationale:
Terminating an idle ssh session within a short time period reduces the window of opportunity for unauthorized personnel to take control of a management session enabled on the console or console port that has been let unattended.
Severity: 
medium
Rule ID:xccdf_org.ssgproject.content_rule_sshd_set_idle_timeout
Identifiers and References

References:  BP28(R29), 1, 12, 13, 14, 15, 16, 18, 3, 5, 7, 8, 5.5.6, APO13.01, BAI03.01, BAI03.02, BAI03.03, DSS01.03, DSS03.05, DSS05.04, DSS05.05, DSS05.07, DSS05.10, DSS06.03, DSS06.10, 3.1.11, CCI-000879, CCI-001133, CCI-002361, 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 6.2, A.12.4.1, A.12.4.3, A.14.1.1, A.14.2.1, A.14.2.5, A.18.1.4, A.6.1.2, A.6.1.5, A.7.1.1, A.9.1.2, A.9.2.1, A.9.2.2, A.9.2.3, A.9.2.4, A.9.2.6, A.9.3.1, A.9.4.1, A.9.4.2, A.9.4.3, A.9.4.4, A.9.4.5, CIP-004-6 R2.2.3, CIP-007-3 R5.1, CIP-007-3 R5.2, CIP-007-3 R5.3.1, CIP-007-3 R5.3.2, CIP-007-3 R5.3.3, CM-6(a), AC-17(a), AC-2(5), AC-12, AC-17(a), SC-10, CM-6(a), DE.CM-1, DE.CM-3, PR.AC-1, PR.AC-4, PR.AC-6, PR.AC-7, PR.IP-2, Req-8.1.8, 8.2.8, SRG-OS-000126-GPOS-00066, SRG-OS-000163-GPOS-00072, SRG-OS-000279-GPOS-00109, SRG-OS-000395-GPOS-00175, UBTU-20-010037, 5.2.15


# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

sshd_idle_timeout_value='300'


if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*ClientAliveInterval\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "ClientAliveInterval $sshd_idle_timeout_value" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "ClientAliveInterval $sshd_idle_timeout_value" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi

Rule   Disable SSH Access via Empty Passwords   [ref]

Disallow SSH login with empty passwords. The default SSH configuration disables logins with empty passwords. The appropriate configuration is used if no value is set for PermitEmptyPasswords.
To explicitly disallow SSH login from accounts with empty passwords, add or correct the following line in /etc/ssh/sshd_config: 
PermitEmptyPasswords no
Any accounts with empty passwords should be disabled immediately, and PAM configuration should prevent users from being able to assign themselves empty passwords.
Rationale:
Configuring this setting for the SSH daemon provides additional assurance that remote login via SSH will require a password, even in the event of misconfiguration elsewhere.
Severity: 
high
Rule ID:xccdf_org.ssgproject.content_rule_sshd_disable_empty_passwords
Identifiers and References

References:  NT007(R17), 11, 12, 13, 14, 15, 16, 18, 3, 5, 9, 5.5.6, APO01.06, BAI10.01, BAI10.02, BAI10.03, BAI10.05, DSS05.02, DSS05.04, DSS05.05, DSS05.07, DSS06.02, DSS06.03, DSS06.06, 3.1.1, 3.1.5, CCI-000366, CCI-000766, 164.308(a)(4)(i), 164.308(b)(1), 164.308(b)(3), 164.310(b), 164.312(e)(1), 164.312(e)(2)(ii), 4.3.3.2.2, 4.3.3.5.1, 4.3.3.5.2, 4.3.3.5.3, 4.3.3.5.4, 4.3.3.5.5, 4.3.3.5.6, 4.3.3.5.7, 4.3.3.5.8, 4.3.3.6.1, 4.3.3.6.2, 4.3.3.6.3, 4.3.3.6.4, 4.3.3.6.5, 4.3.3.6.6, 4.3.3.6.7, 4.3.3.6.8, 4.3.3.6.9, 4.3.3.7.1, 4.3.3.7.2, 4.3.3.7.3, 4.3.3.7.4, 4.3.4.3.2, 4.3.4.3.3, SR 1.1, SR 1.10, SR 1.11, SR 1.12, SR 1.13, SR 1.2, SR 1.3, SR 1.4, SR 1.5, SR 1.6, SR 1.7, SR 1.8, SR 1.9, SR 2.1, SR 2.2, SR 2.3, SR 2.4, SR 2.5, SR 2.6, SR 2.7, SR 5.2, SR 7.6, A.10.1.1, A.11.1.4, A.11.1.5, A.11.2.1, A.12.1.2, A.12.5.1, A.12.6.2, A.13.1.1, A.13.1.3, A.13.2.1, A.13.2.3, A.13.2.4, A.14.1.2, A.14.1.3, A.14.2.2, A.14.2.3, A.14.2.4, A.6.1.2, A.7.1.1, A.7.1.2, A.7.3.1, A.8.2.2, A.8.2.3, A.9.1.1, A.9.1.2, A.9.2.1, A.9.2.3, A.9.4.1, A.9.4.4, A.9.4.5, AC-17(a), CM-7(a), CM-7(b), CM-6(a), PR.AC-4, PR.AC-6, PR.DS-5, PR.IP-1, PR.PT-3, FIA_UAU.1, Req-2.2.4, 2.2.6, SRG-OS-000106-GPOS-00053, SRG-OS-000480-GPOS-00229, SRG-OS-000480-GPOS-00227, UBTU-20-010047, 5.2.10


Complexity:low
Disruption:low
Strategy:restrict
- name: Disable SSH Access via Empty Passwords
  block:

  - name: Check for duplicate values
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      state: absent
    check_mode: true
    changed_when: false
    register: dupes

  - name: Deduplicate values from /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: false
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      state: absent
    when: dupes.found is defined and dupes.found > 1

  - name: Insert correct line to /etc/ssh/sshd_config
    lineinfile:
      path: /etc/ssh/sshd_config
      create: true
      regexp: (?i)^\s*PermitEmptyPasswords\s+
      line: PermitEmptyPasswords no
      state: present
      insertbefore: ^[#\s]*Match
      validate: /usr/sbin/sshd -t -f %s
  when: ansible_virtualization_type not in ["docker", "lxc", "openvz", "podman", "container"]
  tags:
  - CJIS-5.5.6
  - DISA-STIG-UBTU-20-010047
  - NIST-800-171-3.1.1
  - NIST-800-171-3.1.5
  - NIST-800-53-AC-17(a)
  - NIST-800-53-CM-6(a)
  - NIST-800-53-CM-7(a)
  - NIST-800-53-CM-7(b)
  - PCI-DSS-Req-2.2.4
  - PCI-DSSv4-2.2.6
  - high_severity
  - low_complexity
  - low_disruption
  - no_reboot_needed
  - restrict_strategy
  - sshd_disable_empty_passwords

Complexity:low
Disruption:low
Strategy:restrict
# Remediation is applicable only in certain platforms
if [ ! -f /.dockerenv ] && [ ! -f /run/.containerenv ]; then

if [ -e "/etc/ssh/sshd_config" ] ; then
    
    LC_ALL=C sed -i "/^\s*PermitEmptyPasswords\s\+/Id" "/etc/ssh/sshd_config"
else
    touch "/etc/ssh/sshd_config"
fi
# make sure file has newline at the end
sed -i -e '$a\' "/etc/ssh/sshd_config"

cp "/etc/ssh/sshd_config" "/etc/ssh/sshd_config.bak"
# Insert before the line matching the regex '^Match'.
line_number="$(LC_ALL=C grep -n "^Match" "/etc/ssh/sshd_config.bak" | LC_ALL=C sed 's/:.*//g')"
if [ -z "$line_number" ]; then
    # There was no match of '^Match', insert at
    # the end of the file.
    printf '%s\n' "PermitEmptyPasswords no" >> "/etc/ssh/sshd_config"
else
    head -n "$(( line_number - 1 ))" "/etc/ssh/sshd_config.bak" > "/etc/ssh/sshd_config"
    printf '%s\n' "PermitEmptyPasswords no" >> "/etc/ssh/sshd_config"
    tail -n "+$(( line_number ))" "/etc/ssh/sshd_config.bak" >> "/etc/ssh/sshd_config"
fi
# Clean up after ourselves.
rm "/etc/ssh/sshd_config.bak"

else
    >&2 echo 'Remediation is not applicable, nothing was done'
fi
Red Hat and Red Hat Enterprise Linux are either registered trademarks or trademarks of Red Hat, Inc. in the United States and other countries. All other names are registered trademarks or trademarks of their respective companies.